Instrukcja obsługi Definitive Technology BP-8080ST

Definitive Technology głośnik BP-8080ST

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Definitive Technology BP-8080ST (12 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Definitive Technology

BIPOLAR SUPERTOWER

OWNER’S MANUAL

BP-8000 SuperTower®Series:

BP-8080ST, BP-8060ST, BP-8040ST, BP-8020ST

Thank you for choosing the Definitive Technology Bipolar SuperTower Loudspeaker

System. The Bipolar ST is a unique speaker which features For d-Focused Bipolarwar

array technology and a built-in powered subwoofer. This extraordinary speaker is truly

state-of-the-art in music and home theater loudspeaker technology and performance.

You have chosen wisely.

Our engineers have spent many years in developing this product. In order to ensure

that you experience the finest performance possible, we encourage you to take a

moment to fully read this owner’s manual and familiarize yourself with the proper

installation and set-up procedures for your Bipolar ST speakers.

www.DefinitiveTech.com

CAUTION: Important Safety Instructions

WARNING: DO NOT OPERATE SPEAKER WITHOUT

STABILIZER FEET INSTALLED

Accessories included in your Bipolar ST box:

1. Stabilizer Feet: Qty (4) BP-8080ST, BP-8060ST, and BP-8040ST; Qty (2) BP-8020ST

2. Philips Head Screws: Qty (8) BP-8080ST, BP-8060ST, and BP-8040ST;

Qty (4) BP-8020ST

3. Carpet Spikes: Qty (4) all models

4. Hard Floor Glides: Qty (4) all models

Accessory Installation

Power Supply

1. The fuse and power disconnect device are located on the back of the speaker.

2. The disconnect device is the power cord, detachable at either the speaker

or the wall.

Unpacking Your BP-8000 Super Tower

Please Inspect For Shipping Damage

Each loudspeaker leaves our plant in perfect condition. Any visible or concealed

damage most likely occurred in handling after it left our plant and should be

reported to your Definitive dealer or the delivery company that delivered your

loudspeaker. Please unpack your system carefully. Save all cartons and packing

materials in case you move or need to ship your system. Record the serial number

found on the back of the Bipolar 8000ST speaker.

Positioning the Speakers in Your Room

Your new Bipolar speakers are very flexible in terms of positioning and placement.

To optimize their performance, please follow these simple guidelines. Although the

following recommendations will usually yield the best results, all rooms and listen-

ing setsups are different,

so do not be afraid to

experiment with the

speaker placement.

Whatever sounds best to

you is correct.

Figure 2 –

Positioning Bipolar

ST as Left/Right

Main Speakers

Set up the speakers and

listening position in an

equilateral triangle as

illustrated. You will also

get good results if the

listeners are a bit farther away. For example, if line A and C are each 10' long then

line B would be between 7' and 8' long.

Definitive Technology

Safety Precautions

CAUTION! To reduce the risk of electric shock and fire, do not remove the

cover or back plate of this device. There are no user serviceable parts inside.

Please refer all servicing to licensed service technicians. Avis: Risque de choc

electricque, ne pas ouvrir.

CAUTION! The international symbol of a lightning bolt inside a triangle is

intended to alert the user to uninsulated “dangerous voltage” within the

device’s enclosure. The international symbol of an exclamation point inside

a triangle is intended to alert the user to the presence of important operat-

ing, maintenance and servicing information in the manual accompanying

the device.

CAUTION! To prevent electrical shock, match wide blade of plug to wide

slot, fully insert. Attention: Pour eviter les chocs electriques, introduire la

lame la plus large de la fiche dans la borne correspondante de la prise et

pousser jusqu'au fond.

CAUTION! To reduce the risk of electrical shock, do not expose this equip-

ment to rain or moisture.

1. Read Instructions—All safety and operating instructions should be read

before operating the device.

2. Retain Instructions—The safety and operating instructions should be

retained for future reference.

3. Heed Warnings—All warnings on the device and in the operating

instructions should be adhered to.

4. Follow Instructions—All operating and safety instructions should be

followed.

5. Water & Moisture—The device should never be used in, on or near

water for risk of fatal shock.

6. Carts & Stands—The device should only be used on carts or stands rec-

ommended by the manufacturer.

7. Wall & Ceiling Mounting—The device should be mounted on a wall or

ceiling only as recommended by the manufacturer.

8. Ventilation—The device should always be located in such a way that it

maintains proper ventilation.

It should never be placed in a built-in installation or anywhere that

may impede the flow of air through its heat sink.

9. Heat—Never locate the device near heat sources such as radiators, floor

registers, stoves or other heat-generating devices.

10. Power Supply—The device should only be connected to a power supply

of the type described in the operating instructions or as marked on the

device.

11. Power Cord Protection—Power cables should be routed so they are not

likely to be stepped on or crushed by items placed on them or against

them. Special attention should be paid to areas where the plug enters a

socket or fused strip and where the cord exits the device.

12. Cleaning—The device should be cleaned in accordance with manufac-

turer’s instructions.

13. Periods Of Non-Use—The device should be unplugged when not being

used for extended periods.

14. Dangerous Entry—Care should be taken that no foreign objects or

liquids fall or are spilled inside the device.

15. Damage Requiring Service—The device should be serviced by licensed

technicians when:

• The plug or power supply cord has been damaged.

• Objects have fallen on or liquid has spilled inside the device.

• The device has been exposed to moisture.

• The device does not appear to be operating properly or exhibits a

marked change in performance.

• The device has been dropped or the cabinet becomes damaged.

16. Service—The device should always be serviced by licensed technicians.

Only replacement parts specified by the manufacturer should be used.

The use of unauthorized substitutions may result in fire, shock, or other

hazards.

BIPOLAR SUPERTOWER

OWNER’S MANUAL

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Figure 1 – Stabilizer Feet

*Definitive Technology is

not responsible for damage

to floors caused by misuse

of the provided accessories.

Stabilizer Feet and Screws

Optional Carpet Spikes

4”

(10 cm)

6”

(30 cm)

6”

(30 cm)

Connecting Your Loudspeakers

Figure 3 – Wiring and Polarity

Wiring Options: High Level, High Level and LFE w/ “Y” Connector

VERY IMPORTANT:

Do not use your receiver’s auto setup functions as they are often

ineffective in setting up and adjusting speakers with built-in

powered subwoofers!

Use the manual speaker setup func-

tions in your receiver to set speaker

configuration, speaker distance and

channel balance. Consult your

receiver’s or processor’s manual to

learn how to access and use the setup

menus. Use the settings called for in

Figur 4.e

Powering the Active Subwoofer

Your Bipolar STs contain a built-in subwoofer amplifier that must be plugged into

an electrical socket. When powering up from being unplugged, the LED on the

amplifier panel will flash for 30 seconds while the firmware is loading. The

Bipolar ST has a special circuit which automatically turns on when a signal is fed

to the loudspeaker. The LED on the back panel will light up when a signal is

sensed and the amplifier turns on. After the cessation of a signal, it may take up

to an hour for the amplifier to turn off. Due to stray radio signals (RF) in your

area, the LEDs may not turn off. Do not be concerned, the amplifiers draw little

power when they are idle.

Setting Your Speakers’ Low-Frequency Level Control

Your Bipolar STs have bass level controls which allow you to adjust the output

level of the powered subwoofers to match your room and personal listening

preferences. Please note that there are no controls to

vary the crossover points or phase. The crossover

points and phase have been factory-calibrated to

provide perfect blending. We suggest beginning with

the level control set at approximately 12 o’clock.

Each speaker’s bass controls can also be set differently

in order to allow you to compensate for asymmetrical

positioning of the speakers in your room (i.e., when

one is closer to a side wall or corner, etc.).

Complete Home Theater System

We strongly suggest that you use matching Definitive center channel and

rear/surround speakers to complete your Definitive home theater system. Please

note that you can use Definitive Bipolar SuperTowers as rear or side surround

speakers with excellent results for both music and movies.

Troubleshooting

If you experience any difficulties with your Bipolar ST loudspeakers, try the

suggestions below. If you still have problems, contact your Definitive Technology

Authorized Dealer for assistance.

1. Audible distortion when the speakers are playing at loud levels is caused

by turning up your receiver or amplifier louder than the receiver or the

speakers are capable of playing. Most receivers and amplifiers put out their

full-rated power well befor the volume control is turned all the way up, so e

the position of the volume control is a poor indicator of its power limit. If

your speakers distort when you play them loud, turn the volume down!

2. If you experience a lack of bass, it is likely that one speaker is out of phase

(polarity) with the other and needs to be rewired with closer attention to

connecting positive to positive and negative to negative on both channels.

Most speaker wire has some indicator (such as color-coding, ribbing or

writing) on one of the two conductors to help you maintain consistency.

It is essential to connect both speakers to the amplifier in the same way

(in phase).

3. Make sure all your system interconnects and power cords are solidly in place.

4. Should you hear hum or noise coming from your speakers, try plugging

the speakers’ power cords into a different AC circuit than your amplifier.

5. The system has sophisticated internal protection circuitry. If for some

reason the protection circuitry trips, turn off your system and wait five

minutes before trying the system again. If the speakers’ built-in amplifier

should over-heat, the system will turn off until the amplifier cools down

and resets.

6. Check to be sure that your power cord has not been damaged.

7. Check that no foreign objects or liquid has entered the speaker cabinet.

8. If you cannot get the subwoofer driver to turn on or if no sound comes out

and you are sure the system is set up properly, please bring the loudspeaker

to your Definitive Technology Authorized Dealer for assistance; call first.

RECE IV ER/

AMPL IF IE R

Receiver/Amplifier

Strip 1/4" (6mm) wire. Identify markings on wire and assign +/-.

Ensure that the speaker is always con-

nected to the receiver or amplifier + to +

and – to –.

Speaker Setup

Speaker Sub

Large Yes

Subwoofer

level

Subwoofer

level

LFE

speaker output

LFE

Receiver/Amplifier

Right Left

“Y” Connector *available from dealer

Subwoofer

level

on/of LEDf

LFE

Connection Option 1

Receiver/Amplifier

speaker output

Speaker Setup

Speaker Sub

Large No

Figure 4 – Receiver Settings

LFE

Connection Option 2

Min Max

1. Unscrew binding post and insert wire.

2. Tighten until wire is secure.

BIPOLAR SUPERTOWER

OWNER’S MANUAL

Specyfikacje produktu

Marka:	Definitive Technology
Kategoria:	głośnik
Model:	BP-8080ST

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Definitive Technology BP-8080ST, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Definitive Technology

Definitive Technology Dymension DW-45 MAX Instrukcja

8 Października 2024

Definitive Technology Dymension DW-65 MAX Instrukcja

8 Października 2024

Definitive Technology Dymension DW-65 PRO Instrukcja

8 Października 2024

Definitive Technology Dymension DC-80 MAX SUR Instrukcja

8 Października 2024

Definitive Technology Mythos LCR-75 Instrukcja

7 Października 2024

Definitive Technology Mythos LCR-85 Instrukcja

7 Października 2024

Definitive Technology Mythos LCR-65 Instrukcja

5 Października 2024

Definitive Technology Mythos ST Instrukcja

3 Października 2024

Definitive Technology ProCinema 1000 Instrukcja

22 Września 2024

Definitive Technology BPVX Instrukcja

21 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel Rockster Air Instrukcja

15 Października 2024

Alpine PSS-22WRA Instrukcja

15 Października 2024

Bauhn APPS-0724 Instrukcja

15 Października 2024

Aiwa SP-A100 Instrukcja

15 Października 2024

Harman Kardon Citation One Instrukcja

14 Października 2024

Alpine 30MC Instrukcja

14 Października 2024

Magnat Needle 9000 ALU Instrukcja

14 Października 2024

Pioneer SP-T22A-LR Instrukcja

14 Października 2024

Sharp PS-932 Instrukcja

14 Października 2024

Pyle PDWR64BTW Instrukcja

13 Października 2024