Instrukcja obsługi CyberPower RELAYIO600

CyberPower Niesklasyfikowane RELAYIO600

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberPower RELAYIO600 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Rela
R
Quic
CyberPower Systems (US
4241 12th Avenue East S
Phone: 877-297-6937
Fax: 952-403-0009
www.CPSww.com
ay Control
Card
RELAYIO6
00
ck Reference Guide
SA), Inc.
uite 400 Shakopee, MN 55379
d
K01-0000427-00
Overview
The CyberPower Relay
solution for UPS status m
relays. In addition, the
R
UPS shutdown
in bat
CyberPower Online UPS
s
Installation G
Notice: The UPS can rem
1. Remove the
two retai
remove the cover.
2.
Install the CyberPowe
3. Re-
install and tighten
Technical Spe
Electrical
External S/D Voltage
Power Dissipation
Physical
Dimensions (HxWxD
Weight
Environmental
Operating Temperatu
Operating Humidity
Control Card (
RELAYIO600
monitoring and local device co
ELAYIO600
provides
1 input co
ttery mode
.
This card is
system
s with an
expansion po
uide
ain on when installing the
REL
ining screws of the expansion
er
RELAYIO600 card
into the ex
the retaining screws.
ecifications
RELAYIO600
e
7.5 -
12
1.35W M
(Default 12V
D)
43 x 67 x 1
55
1.7 x 2.64 x
6
88.6 g / 3.1
ure
0 - 40
32 - 104
0 to 95%
) offers users a
ntrol
via 5 output
ontact to perform
compatible with
ort.
LAYIO600 card
.
port cover then
xpansion port.
V
Max
input)
5
.7 mm
6.13
in
13 oz
%
Internal Circuit-DB9
I/O Pinout Definition-DB9
PIN
Assignment
Function I/O Jumper
PIN 1 UPS FAIL O/P JP1
PIN 2 SUMMARY ALARM O/P JP2
PIN 3 GND (Common for PIN 4)
Power GND N/A
PIN 4 REMOTE SHUTDOWN Power + Vcc
N/A
PIN 5 COMMON (For Relays) O/P N/A
PIN 6 BYPASS / UPS OFF O/P N/A
PIN 7 BATTERY LOW O/P JP3
PIN 8 UPS ON O/P N/A
PIN 9 POWER FAIL O/P JP4
Note1: Relay contact PIN 1/2/7/9 can be configured as Normally Open (NO)
or Normally Closed (NC).
Note2: Please see the Function Description section for details on jumper
position settings.
Internal Circuit-Terminal Block
I/O Pinout Definition-Terminal Block
Terminal
Assignment
Function I/O Jumper
T1 REMOTE SHUTDOWN Power + Vcc
N/A
T2 GND (Common for PIN 4)
Power GND N/A
T3 SUMMARY ALARM O/P JP2
T4 BYPASS / UPS OFF O/P N/A
T5 BATTERY LOW O/P JP3
T6 POWER FAIL O/P JP4
T7 UPS ON O/P N/A
T8 UPS FAIL O/P JP1
T9 COMMON (For Relays) O/P N/A
T10 COMMON (For Relays) O/P N/A
Note1: Relay contact T3/5/6/8 can be configured as Normally Open (NO) or
Normally Closed (NC).
Note2: Please see the Function Description section for details on jumper
position settings.
Output Relay Rating
Max Voltage Current
30VDC/125VAC 3A (per relay)
Function Description
NO/NC
Jumper
Position
Status Condition
JP1 NO
PIN 1 short to PIN 5 Activated on UPS Fault
(Inverter Fault / DC Bus Fault / Over Temperature
/ Bat Test Fail / Bat Over Charge / Fan Error)
T8 short to T9/T10
JP1 NC
PIN 1 open to PIN 5
T8 open to T9/T10
JP2 NO
PIN 2 short to PIN 5 Activated on Summary alarm
(Inverter Fault / Output Short / DC Bus Fault /
Over Temperature / Over Load / Bat Over Charge
/ Battery Low / Bat Test Fail / Wiring Fault / Load
Over Setting Level / Fan Error)
T3 short to T9/T10
JP2 NC
PIN 2 open to PIN 5
T3 open to T9/T10
N/A PIN 6 short to PIN 5 Activated when UPS is OFF or in Bypass Mode
T4 short to T9/T10
JP3 NO
PIN 7 short to PIN 5
Activated when Battery Low
T5 short to T9/T10
JP3 NC
PIN 7 open to PIN 5
T5 open to T9/T10
N/A PIN 8 short to PIN 5 UPS is on
T7 short to T9/T10
JP4 NO
PIN 9 short to PIN 5
Activated when Utility Power Fails
T6 short to T9/T10
JP4 NC
PIN 9 open to PIN 5
T5 open to T9/T10
Example Application
Provide 12VDC from (PIN 5/T9/T10) to (PIN 3/T2). COMMON GND
1. Remote Monitor Install alerting mechanism from DB-9 port/
Terminal(PIN 1/T8, PIN 2/T3, PIN 6/T4, PIN 7/T5, PIN 8/T7, PIN 9/T6)
to (PIN 3/T2). GND
2. Remote Shutdown Install a push button from COMMON
(PIN 5/T9/T10) to REMOTE SHUTDOWN(PIN 4/T1). Press the
button for at least 5 seconds to shut off the UPS remotely.
Note: When the UPS is in battery mode, the shutdown pins
(PIN 4 & PIN 3) require a minimum of 5 seconds of high level signal
(connection to +12VDC) to perform the UPS shutdown where output is
turned off after 120 seconds.
1
6
2
7
3
4
5
8
9
UPS FAIL
SUMMARY ALARM
GND (Common for PIN 4)
REMOTE SHUTDOWN
COMMON (For Relays)
BYPASS / UPS OFF
BATTERY LOW
UPS ON
POWER FAIL
12V
Conformance Approvals
FCC Warning
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does not cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
CyberPower Technical Support
Phone: 1-877-297-6937
Email: tech@cpsww.com
Web: www.CPSww.com
Mail: 4241 12th Avenue E, Suite 400 Shakopee, MN 55379
Hours of Operation:
Monday – Friday, 7:00am – 6:00pm (CST)
Entire contents copyright © 2015 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is
prohibited.

Specyfikacje produktu

Marka: CyberPower
Kategoria: Niesklasyfikowane
Model: RELAYIO600

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CyberPower RELAYIO600, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane CyberPower

CyberPower

CyberPower Rackbar RKBS20ST6F12R Instrukcja

12 Października 2024
CyberPower

CyberPower PR1000ELCDRT2U Instrukcja

10 Października 2024
CyberPower

CyberPower Essential B704 Instrukcja

10 Października 2024
CyberPower

CyberPower SB0602BA-DE-B50 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0802AD-DE-W24 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0502BA-DE-B70 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0502BA-DE-W70 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0702AD-DE-B30 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0602BA-DE-W18 Instrukcja

9 Października 2024
CyberPower

CyberPower SB0702AD-DE-W30 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024