Instrukcja obsługi Cudy IG1005

Cudy przełącznik IG1005

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cudy IG1005 (2 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
CE Mark Warning
Safety Instructions
This is a Class product. In a stic environm t, this product may A dome en
cause r io terference, in which case the user may be req red to take ad in ui
adequate m sures.ea
Regulatory Statements
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
Non-modifcation Statement
Any changes or modifcations not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
The following general safety guidelines are provided to help ensure your
own personal safety and protect your product from potential
damage. Remember to consult the product user instructions for
more details.
Static electricity can be harmful to electronic components.
Discharge static electricity from your body (i.e. touching grounded
bare metal) before touching the product.
Do not attempt to service the product and never disassemble the
product. For some products with user replaceable battery, please
read and follow the instructions in the user manual.
Do not spill food or liquid on your product and never push any
objects into the openings of your product.
Do not use this product near water, areas with high humidity or
condensation unless the product is specifcally rated for outdoor
application.
Keep the product away from radiators and other heat sources.
Always unplug the product from mains power before cleaning and
use a dry lint free cloth only
EU declaration of conformity
Cudy hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at
http://www.cudy.com/ce.
Quick Installation Guide
Industrial Switch
810600122
Email:
support@cudy.com
Website:
www.cudy.com
Quick Reference
Hardware Installation
1Ground Connecting
3
Ethernet Interface Connecting
(RJ45 Ethernet)
4
2
LED Indicator
6
Note: The switch model and power supply may be different from the
one shown in the example below. The power supply sold separately.
The switch must be properly grounded for optimum system performance.
1. Hook the unit over the DIN rail.
2. Push the bottom of the unit towards the DIN Rail until it snaps into
place.
Power
RJ45 indicator
LINK/ACT
Red LED on
Red LED off
Yellow LED on
Yellow LED flashing
Green LED on
Yellow/Green LED off
Green LED on
Green LED flashing
Power supplying in normal
Power supply abnormal or no powering
Network connection in normal
Link communication in normal
PoE feeding in normal
No connection at port
Optical network Connection in normal
Link connection in normal
LED Status Definition
Mounting the unit Releasing the unit
Connecting the Ethernet interface via RJ45:
To connect to a PC, use a straight-through or a cross-over Ethernet
cable.
To connect the switch to an Ethernet device, use UTP (Unshielded
Twisted Pair) or STP (Shielded Twisted Pair) Ethernet cables.
The pin assignment of RJ-45 connector is shown in the
following figure and table.
Pin
MDI signal
MDI-X signal
1
TX+
RX+
2
TX-
RX-
3
TX+
RX+
6
TX-
RX-
4,5,7,8
-
-
Power Connecting
5
The switch can be powered from two power supply (input range 12V –
57V for industrial switch or 48 57V for PoE industrial switch). Insert ～
the positive and negative wires (AWG 14-26) into V+ and V- contact on
the terminal block and tighten the wire-clamp screws to prevent the wires
from being loosened.
NOTE:
1. The DC power should be connected to a
well-fused power supply.
2. Input power should be within the range of
50~57VDC for PoE+ compliant, or
48~57VDC for PoE compliant.

Specyfikacje produktu

Marka: Cudy
Kategoria: przełącznik
Model: IG1005

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cudy IG1005, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Cudy

Cudy

Cudy GS105U Instrukcja

5 Grudnia 2024
Cudy

Cudy FS1006P Instrukcja

9 Października 2024
Cudy

Cudy FS1010P Instrukcja

9 Października 2024
Cudy

Cudy GS105 Instrukcja

9 Października 2024
Cudy

Cudy GS1008PS2 Instrukcja

8 Października 2024
Cudy

Cudy GS1010PS2 Instrukcja

8 Października 2024
Cudy

Cudy GS1010P Instrukcja

8 Października 2024
Cudy

Cudy GS1026PS2 Instrukcja

8 Października 2024
Cudy

Cudy GS1005PTS1 Instrukcja

8 Października 2024
Cudy

Cudy HS105 Instrukcja

8 Października 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Powerfix

Powerfix PSSS 2 A1 Instrukcja

14 Stycznia 2025
INOGENI

INOGENI CAM230 Instrukcja

14 Stycznia 2025
Schneider

Schneider CCT15225 Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-5248P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2624P Instrukcja

14 Stycznia 2025
Luxul

Luxul XGS-1005 Instrukcja

14 Stycznia 2025
Luxul

Luxul AGS-1008M Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-1208P Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-7048P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2600 Instrukcja

14 Stycznia 2025