Instrukcja obsługi Ctek MXS 10.0

Ctek Ładowarka baterii MXS 10.0

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ctek MXS 10.0 (6 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
EN
EN • 3
CONGRATULATIONS
to the purchase of your new professional switch mode battery charger.
This charger is included in a series of professional chargers from CTEK AB and SWEDEN
represents the latest technology in battery charging.
CTEK COMFORT CONNECT – eyelet M8
CTEK COMFORT CONNECT
MAINS CABLE
CTEK COMFORT CONNECT – clamp
CHARGE CABLE
SUPPLY PLUG*
*Supply plugs m ay differ to suit your wall socket.
Attach t he temperat ure sensor to the charger.
Attach t he temperat ure sensor to the clamp.
NORMAL
BATT ERY
PROGRAM
ERROR LAMP
AGM
BATT ERY
PROGRAM
FULLY DCHARGEREADY TO USE
RECOND
PROGRAM
SUPPLY
PROGRAM
POWER
LAMP
CHARGING
1. Connect the charger to the battery.
2. Connect the charger to the wall socket. The power lamp will indicate that the mains
cable is connected to the wall socket. The error lamp will indicate if the battery clamps
are incorrectly connected. The reverse polarity protection will ensure that the battery
or charger will not be damaged.
3. Press the MODE-button to select charging program.
4. Follow the 8-step display through the charging process.
The battery is ready to start the engine when STEP 4 is lit.
The battery is fully charged when STEP 7 is lit.
5. Stop charging at any time by disconnecting the mains cable from the wall socket.
MODE-
BUT TON
TEMPERATURE
SENSOR
TEMPERATURE
SENSOR
INDICATOR
MANUAL
1
1
2
2
20014905E MXS 10, Manual EU, Print file 004.indd 3 2011-10-11 08:50:46
4 • EN
BATTERY SIZE (Ah) TIME TO 80% CHARGED
20Ah 2h
50Ah 5h
100Ah 10h
200Ah 20h
READY TO USE
The table shows the estimated time for empty battery to 80% charge
CHARGING PROGRAMS
Settings are made by pressing the MODE-button. After about two seconds the charger
activates the selected program. The selected program will be restarted next time the
charger is connected.
The table explains the different Charging Programs:
Program Battery
Size (Ah) Explanation Temp range
20–300Ah
Normal battery program
14.4V/10A. Use for WET batteries,
Ca/Ca, MF and for most GEL batteries
-20°C–+50°C
(-4ºF–122ºF)
AGM 20–300Ah AGM battery program 14.7V/10A
Use for AGM batteries.
-20°C–+50°C
(-4ºF–122ºF)
RECOND 20–300Ah
Recond program 15.8V/1.5A
Use to return energy to the empty
WET and Ca/Ca batteries. Recond
your battery once per year and after
deep dischare to maximise lifetime
and capacity. The Recond program
adds STEP 6 to the normal battery
program. Frequent use of the Recond
program may cause water loss in the
batteries and reduce service life of
electronics. Contact your vehicle and
battery supplier for advice.
-20°C–+50°C
(-4ºF–122ºF)
20–300Ah
Supply program 13.6V/10A
Use as 12V power supply or use for
float maintenance charging when 100%
capacity of the battery is required.
Supply program activates step 7 without
time or voltage limitation.
-20°C–+50°C
(-4ºF–122ºF)
ERROR LAMP
If the error lamp is lit, check the following:
1. Is the chargers positive lead connected to the batterys
positive pole?
2. Is the charger connected to a 12V battery?
3. Has charging been interrupted in STEP 1, 2 or 5?
Restart the charger by pressing the MODE-button. If charging is still
being interrupted, the battery...
STEP 1: ...is seriosly sulphated and may need to be replaced.
STEP 2: ...can not accept charge and may need to be replaced.
STEP 5: ...can not keep charge and may need to be replaced.
TEMPERATURE SENSOR
The MXS 10 is equipped with an external temperature sensor. The tempera-
ture sensor is attachable. If so, the charger will compensate voltage accor-
ding to ambient temperature. Activated temperature sensor will be indicated
by a lit temperature sensor indicator lamp.
WARNING!
The spark protection on the battery charger
is disabled during SUPPLY program.
POWER LAMP
If the power lamp is lit with a:
1. STEADY LIGHT
The mains cable is connected to the wall socket.
2. FLASHING LIGHT:
The charger has entered the energy save mode. This happens if the
charger isn´t connected to the battery in 2 minutes.
20014905E MXS 10, Manual EU, Print file 004.indd 4 2011-10-11 08:50:50
EN
EN • 5
STEP 1 dESULPHATION
Detects sulphated batteries. Pulsing current and voltage, removes sulphate from the lead
plates of the battery restoring the battery capacity.
STEP 2 SOFT START
Tests if the battery can accept charge. This step prevents that charging proceeds with a
defect battery.
STEP 3 BULK
Charging with maximum current until approximately 80% battery capacity.
STEP 4 ABSORPTION
Charging with declining current to maximize up to 100% battery capacity.
STEP 5 ANALYSE
Tests if the battery can hold charge. Batteries that can not hold charge may need to be replaced.
STEP 6 dRECON
Choose the Recond program to add the Recond step to the charging process. During the Recond step
voltage increases to create controlled gasing in the battery. Gasing mixes the battery acid and gives
back energy to the battery.
STEP 7 FLOAT
Maintaining the battery voltage at maximum level by providing a constant voltage charge.
STEP 8 PULSE
Maintaining the battery at 95–100% capacity. The charger monitors the battery voltage and gives a
pulse when necessary to keep the battery fully charged.
1
VOLTAGE (V)CURRENT (A)
ANALYSE RECOND PULSE
DESULPHATION SOFT START BULK ABSORPTION
15.8V
Increasing voltage
to 14.7V @ 25°C
10A
10A until 12.6V Increasing voltage
to 14.4V @ 25°C
10A
1 7
Limit: Max 20h Max 10h 3 minutes 30 min or 4h
depending on
battery voltage
10 days
Charge cycle restarts
if voltage drops*
Charge cycle restarts
if voltage drops
Max 8h
15.8V
15.8V 10A until 12.6V
10A until 12.6V
Increasing voltage
to 14.4V @ 25°C
10A
14.4V @ 25°C
Declining current
14.7V @ 25°C
Declining current
14.4V @ 25°C
Declining current
Checks if voltage
drops to 12V
Checks if voltage
drops to 12V
Checks if voltage
drops to 12V
Max 13.6V
10A
13.6V
10A
13.6V
10A
13.6V
10A
12.7V‒14.4V
10‒2A
12.7V‒14.7V
10‒2A
12.7V‒14.4V
10‒2A
Max 8h
2 3 4 5
FLOAT
6 8
RECOND
SUPPLY
AGM
Max 15.8V
1.5A
*Supply program is not time or voltage limited.
CHARGING PROGRAM
20014905E MXS 10, Manual EU, Print file 004.indd 5 2011-10-11 08:50:50

Specyfikacje produktu

Marka: Ctek
Kategoria: Ładowarka baterii
Model: MXS 10.0

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ctek MXS 10.0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ładowarka baterii Ctek

Ctek

Ctek READY AUTOMOTIVE Instrukcja

4 Października 2024
Ctek

Ctek MXS 5.0 CHECK Acculader Instrukcja

25 Września 2024
Ctek

Ctek MXS 5.0 POLAR Acculader Instrukcja

25 Września 2024
Ctek

Ctek MXS 5.0 Test and Charge Acculader Instrukcja

25 Września 2024
Ctek

Ctek PRO25SE Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXTS70 Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXT 14 Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXS 3.8 Acculader Instrukcja

23 Września 2024
Ctek

Ctek Njord Go Acculader Instrukcja

23 Września 2024
Ctek

Ctek D250TS Acculader Instrukcja

23 Września 2024

Instrukcje Ładowarka baterii

Najnowsze instrukcje dla Ładowarka baterii

Graupner

Graupner Ultramat 12 Instrukcja

13 Stycznia 2025
Graupner

Graupner ULTRA DUO PLUS 30 Instrukcja

13 Stycznia 2025
Fuxtec

Fuxtec FX-E1LG1A Instrukcja

13 Stycznia 2025
Voltcraft

Voltcraft Charge Manager 410 Instrukcja

11 Stycznia 2025
Nitecore

Nitecore UHX1 PRO Instrukcja

11 Stycznia 2025
Envivo

Envivo ENV-1597 Instrukcja

11 Stycznia 2025
Xblitz

Xblitz XC1 Instrukcja

10 Stycznia 2025
Jackery

Jackery Explorer 240 v2 Instrukcja

7 Stycznia 2025
Jackery

Jackery Explorer 1000 v2 Instrukcja

7 Stycznia 2025
Schwaiger

Schwaiger LSET500 513 Instrukcja

7 Stycznia 2025