Instrukcja obsługi Ctek Lithium XS

Ctek Ładowarka baterii Lithium XS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ctek Lithium XS (6 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
EN
EN • 3
RESET
CONGRATULATIONS
To the purchase of your new professional switch mode battery charger. This charger is
included in a series of professional chargers from CTEK SWEDEN AB and represents the
latest technology in battery charging. The LITHIUM XS charger model is designed for
Lithium-ion batteries using LiFePO4 technology only. Please check with the battery manufac-
turer for details. Do not use the LITHIUM XS charger for any other battery technology.
CTEK COMFORT CONNECT eyelet M6–
CTEK COMFORT CONNECT
MAINS CABLE
CTEK COMFORT CONNECT clamp–
CHARGE CABLE
SUPPLY PLUG*
* Supply plugs may differ to suit your wall socket.
ERROR LAMP
FULLY CHARGEDREADY TO USE
POWER LAMP
HOW TO CHARGE
1. Connect the charger to the battery.
2. Connect the charger to the wall socket.
3. Follow the 8-step display through the charging process.
The battery is ready to start the engine when STEP 3 is lit.
The battery is fully charged when STEP 7 is lit.
4. Stop charging at any time by disconnecting the mains cable from the wall socket.
RESET-BUTTON
MANUAL
BATTERIES WITH "UNDER VOLTAGE PROTECTION"
Some Lithium-ion batteries have an on-board that UVP (under voltage protection)
disconnects the battery to avoid it becoming too deeply discharged. This prohibits the
CTEK charger from detecting that there’s a battery connected. To bypass this, the bat-
tery charger needs to open the UVP. By pressing the RESET-button for 10 seconds, the
charger opens the UVP. During this process, the charging STEP 7 is lit. Once the UVP has
been opened and the battery is ready to be charged, the charger automatically starts the
charging cycle.
4 • EN
BATTERY SIZE (Ah) TIME TO 90% CHARGED
8Ah 2h
20Ah 5h
60Ah 16h
READY TO USE
The table shows the estimated time for an empty battery to reach 90%
state of charge (SOC). Please note that charging times are
longer in low ambient temperatures.
ERROR LAMP
If the error lamp is lit, check the following:
1. Is the chargers positive lead connected to the battery´s
positive pole?
2. Is the charger connected to a 12V LiFePO4 battery?
3. Has charging been interrupted in STEP 1 or 4?
Restart the charger by pressing the RESET-button. If charging is still
being interrupted, the battery...
STEP 1: ...can not accept charge.
...may be too large for the charger to wake up. Press
RESET-button up to 5 times.
...a paralell load may be connected to the battery. Disconnect
the battery and try again.
STEP 4: ...can not keep charge and may need to be replaced.
POWER LAMP
If the power lamp is lit with a:
1. STEADY LIGHT
The mains cable is connected to the wall socket.
2. FLASHING LIGHT:
The charger has entered the energy save mode. This happens if the
charger isn´t connected to the battery within 2 minutes or the battery on
board UVP (under voltage protection) is activated.
CONNECT AND DISCONNECT THE CHARGER TO A BATTERY
Comfort
Connect
INFO
If the battery clamps are incorrectly
connected, the reverse polarity pro-
tection will ensure that the battery
and charger are not damaged.
For batteries mounted inside a
vehicle
1. Connect the red clamp to the bat-
tery's positive pole.
2. Connect the black clamp to the
vehicle chassis remote from the fuel
pipe and the battery.
3. Connect the charger to the wall
socket.
4. Disconnect the charger from the
wall socket before disconnecting the
battery.
5. Disconnect the black clamp before
the red clamp.
Some vehicles may have posi-
tively earthed batteries.
1. Connect the black clamp to the bat-
tery's negative pole.
2. Connect the red clamp to the vehicle
chassis remote from the fuel pipe and
the battery.
3. Connect the charger to the wall
socket.
4. Disconnect the charger from the
wall socket before disconnecting the
battery.
5. Disconnect the red clamp before the
black clamp.
1.
+
+
–
–
Comfort
Connect
EN
EN • 5
STEP 1 ACCEPT
Tests if the battery can accept charge. This step prevents that charging proceeds with a
defect battery.
STEP 2 BULK
Charging with maximum current until approximately 90% battery capacity.
STEP 3 ABSORPTION
Charging with declining current to maximize up to 95% battery capacity.
STEP 4 ANALYSE
Tests if the battery can hold charge. Batteries that can not hold charge may need to be
replaced.
STEP 5 COMPLETION
Final charge with increased current.
STEP 6 MAXIMIZATION
Final charge with maximum voltage up to 100% battery capacity.
STEP 7 FLOAT
Maintaining the battery voltage at maximum level by providing a constant voltage charge.
STEP 8 PULSE
Maintaining the battery at 95–100% capacity. The charger monitors the battery voltage
and gives a pulse when necessary to keep the battery fully charged.
CHARGING PROGRAM
ACCEPT BULK ABSORPTION ANALYSE COMPLETION MAXIMIZATION PULSEFLOAT
VOLTAGE (V)
1
1 7 2 3 4 5 6 8
CURRENT (A)
5A until 11.0V Increasing voltage to
13.8V
5A
Declining current
13.8V
Checks if voltage
drops to 12V
Max
1.5A
Max
14.4V
13.6V
5A
13.4V–13.8V
5.0–1.0A
Limit: Max 30s Max 10h Max 30h 3minutes Max 2h 10 days
Charge cycle restarts
if voltage drops
Charge cycle restarts
if voltage drops

Specyfikacje produktu

Marka: Ctek
Kategoria: Ładowarka baterii
Model: Lithium XS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ctek Lithium XS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ładowarka baterii Ctek

Ctek

Ctek READY AUTOMOTIVE Instrukcja

4 Października 2024
Ctek

Ctek MXS 5.0 CHECK Acculader Instrukcja

25 Września 2024
Ctek

Ctek MXS 5.0 POLAR Acculader Instrukcja

25 Września 2024
Ctek

Ctek MXS 5.0 Test and Charge Acculader Instrukcja

25 Września 2024
Ctek

Ctek PRO25SE Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXTS70 Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXT 14 Acculader Instrukcja

23 Września 2024
Ctek

Ctek MXS 3.8 Acculader Instrukcja

23 Września 2024
Ctek

Ctek Njord Go Acculader Instrukcja

23 Września 2024
Ctek

Ctek D250TS Acculader Instrukcja

23 Września 2024

Instrukcje Ładowarka baterii

Najnowsze instrukcje dla Ładowarka baterii

Graupner

Graupner Ultramat 12 Instrukcja

13 Stycznia 2025
Graupner

Graupner ULTRA DUO PLUS 30 Instrukcja

13 Stycznia 2025
Fuxtec

Fuxtec FX-E1LG1A Instrukcja

13 Stycznia 2025
Voltcraft

Voltcraft Charge Manager 410 Instrukcja

11 Stycznia 2025
Nitecore

Nitecore UHX1 PRO Instrukcja

11 Stycznia 2025
Envivo

Envivo ENV-1597 Instrukcja

11 Stycznia 2025
Xblitz

Xblitz XC1 Instrukcja

10 Stycznia 2025
Jackery

Jackery Explorer 240 v2 Instrukcja

7 Stycznia 2025
Jackery

Jackery Explorer 1000 v2 Instrukcja

7 Stycznia 2025
Schwaiger

Schwaiger LSET500 513 Instrukcja

7 Stycznia 2025