Instrukcja obsługi CRUX VRFPR-66F

CRUX Niesklasyfikowane VRFPR-66F

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CRUX VRFPR-66F (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
VRFPR-66F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031220
1 of 6
• Rear & Front View Camera Inputs
• Oponal coding of ParkAssist to retrot factory PDC
• Automacally switches screen to Rear-view when Reverse gear is engaged and to Front camera view when gear is
engaged to drive
• Manual acvaon of the front camera using the steering wheel control buon
• Plug & Play Installaon
• Video in Moon funcon
PRODUCT FEATURES:
PARTS INCLUDED:
VRFPR-66F Module VRFPR-66F Harness CUL-16 Rear-View Camera
INSTALLATION DIAGRAM:
F
Female Quadlock
Vehicle Harness
Rear-View
Camera Input
OEM Rear-View Camera
Front-View
Camera Input
Rear-Vew Camera
(CUL-16 Included)
Front-View Camera
(not Included)
Rear Camera Output 12V (GREEN)
Front Camera Output 12V (WHITE)
Male Quadlock
Connector behind the
headunit
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031220
2 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
CONNECTING THE INTEFACE MODULE
1. Remove the headunit.
2. Connect the female 12-Pin Molex connector of the VRFPR-66F T-harness to the interface module.
3. Unplug the female Quadlock connector from behind the headunit and plug it into the VRFPR-66F T-harness.
4. Plug the male Quadlock of the VRFPR-66F T-harness to the headunit.
CONNECTING THE FACTORY REAR-VIEW CAMERA (Compable with NTSC cameras only)
5. If the OEM rear-view camera will be used, plug in the male RCA labeled “OEM Rear-View Camera” to the female RCA
labeled “Rear-View Camera”.
CONNECTING THE AFTERMARKET CAMERAS (Compable with NTSC cameras only)
6. If using an aermarket rear-view camera, install the aermarket camera behind the vehicle and run the cable towards the
radio. Plug in the male RCA of the aermarket rear-view camer to the female RCA labeled “Rear-View Camera”.
7. Connect the GREEN wire on the T-harness to the 12V power wire of the aermarket camera. The GREEN wire will provide
12 volts power to the camera when the reverse gear is engaged. Power will deacvate automacally when the gear is set
to drive and speed reaches to 12 MPH.
8. If an aermarket front-view camera will be used, install the camera per manufacturer’s installaon instrucons and run
the extension cable towards the radio. Plug in the male RCA of the aermarket rear-view camer to the female RCA labeled
“Front-View Camera”.
9. Connect the WHITE wire on the T-harness to the 12V power wire of the aermarket camera. The WHITE wire will provide
12 volts power to the camera when the gear is set to drive. Power will deacvate automacally when the speed reaches
12 MPH.
Navigaon System DIP 1 DIP2 DIP3 DIP4 DIP5 DIP6
PCM3 with VIM Acvated OFF OFF OFF OFFON ON
PCM3 with VIM Deacvated OFF OFF OFF OFF OFFON
PCM3.1 with VIM Acvated OFF OFF OFFON ON ON
PCM3.1 with VIM Deacvated OFF OFF OFF OFFON ON
DIP SWITCH FUNCTIONS:
DIP 1 = Video in Moon Acvaon
DIP 2 = ON for OEM Rear View Camera / OFF for Aermarket Rear View Camera
DIP 3 = Rear View Camera Coding (see page 3)
DIP 4 = ParkAssist Coding for PCM3.1 systems only (see page 4)
DIP 5 = Camera/ParkAssist Coding (see page 5)
DIP 6 = CAN Bus Terminaon
The interface module is installed behind the headunit.
VRFPR-66F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0312203 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
CODING THE RADIO FOR CAMERA FUNCTION:
PCM3.1 Systems
It is necessary to code the rear-view camera input of the PCM3.1 system for use with an aermarket rear-view camera.
Le side Steering Wheel Buons Right side Steering Wheel Buons
HASH KEY/MODE
PICK UP
HANG UP
BACK
1. Turn ignion to ON.
2. Wait unl the headunit has completely booted and is in the home screen.
3. Make sure that the LEDs on the interface module is visible during this process. The LEDs are inside the module and are
visible through the side of the male 8-pin Molex connector.
4. Please observe the proper coding sequence: First press and hold the HASH KEY/MODE then press and hold the PICK UP
buon. Connue to hold both buons and check if the RED and BLUE LEDs are blinking. The PCM system will reset aer
5-10 seconds.
5. Release both buons.
6. The RED and BLUE LEDs will light up solid.
7. “Rear-View Camera” will show on the radio menu opon aer a successful coding.
To decode the aermarket rear-view camera from the system, follow the steps below.
1. Turn ignion to ON.
2. Wait unl the headunit has completely booted and is in the home screen.
3. Make sure that the LEDs on the interface module is visible during this process. The LEDs are inside the module and are
visible through the side of the male 8-pin Molex connector.
4. Please observe the proper decoding sequence: First press and hold the HASH KEY/MODE buon then press and hold the
HANG UP buon. Connue to hold both buons and check if the RED and BLUE LEDs are blinking. The PCM system will
reset aer 5-10 seconds.
5. Release both buons.
6. The RED and BLUE LEDs will light up solid.
7. “Rear-View Camera” will no longer show on the radio menu opon aer a successful decoding.
VRFPR-66F
Rear & Front View Integration Interface
for Porsche Vehicles with PCM 3 & 3.1 Navigation Systems

Specyfikacje produktu

Marka: CRUX
Kategoria: Niesklasyfikowane
Model: VRFPR-66F

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CRUX VRFPR-66F, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane CRUX

CRUX

CRUX SOOGM-16 Instrukcja

8 Października 2024
CRUX

CRUX DKGM-16W Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52B Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52 Instrukcja

8 Października 2024
CRUX

CRUX ACP-MAX Instrukcja

8 Października 2024
CRUX

CRUX RFM-MG1 Instrukcja

8 Października 2024
CRUX

CRUX SOCGM-18L Instrukcja

8 Października 2024
CRUX

CRUX SWRGM-49L Instrukcja

8 Października 2024
CRUX

CRUX WVICH-03M Instrukcja

8 Października 2024
CRUX

CRUX WVIFD-02F Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024