Instrukcja obsługi CRUX RVCCH-75WM

CRUX Niesklasyfikowane RVCCH-75WM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CRUX RVCCH-75WM (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/3
- Interface includes Audio / Video Input to connect an extra A/V source.
- OEM style Spare Tire mount reverse camera included.
- Camera has moving parking guide lines to show path direcon while backing up.
- Acvates MYGIG Screen for enabling Video features.
- Supports vehicles with manual transmission. See note below.
- Plug and Play connecons for ease of use.
NOTE: Does not supply +12V Reverse Trigger on vehicles with manual transmission.
Camera power must be tapped from the +12V reverse light wire instead.
-75WM MODULE CH
-75WM HARNESS CH
CCH-01M SPARE TIRE MOUNT CAMERA with MOVING LINES
Rev.0926 17
1 / 3
INSTALLING THE CAMERA AND INTERFACE
1. Remove the outside mounted spare re.
2. Mount the metal bracket onto the spare re bolts and secure with the star washers. camera’s
3. Route the cable towards the radio and make the power and video connecons.
4. Remove the factory radio to gain access to the factory connectors.
5. Plug in the T-harness with WHITE and GRAY connectors. (See Wiring Diagram above)
6. Connect the 8-pin Molex connector from the T-harness with GRAY connectors to the CAN Interface.
7. Use the WHITE 12V Reverse Output wire to power the camera (see Wiring Diagram above). DO NOT
connect the red power wire, near the camera, insulate this red wire to avoid to the reverse light and
from shorng. the vehicle has a manual transmission, the camera power must be tapped to the If
+12V reverse light wire instead. In this case the WHITE 12V Reverse Output wire is not used and
should be insulated to avoid from shorng.
8. Plug in the YELLOW MALE RCA from the camera cable to the YELLOW FEMALE RCA of the T-Harness
with WHITE connectors.
9. Connect GREEN wire to +12V for a non permanent Video in Moon feature.
10. Set the proper DIP Switch sengs on the CAN Interface. (See Chart above)
11. Cut the thin white wire on the camera cable to enable the parking guide lines.
12. Test the camera before re-installing the radio.
Rev.0926 17
2 / 3
Please note that the WHITE 12V
Reverse Output wire does not
supply power on vehicles with
manual transmission and should
be insulated to avoid from
shorng. Connect the camera
power to the OE reverse light
+12V wire instead.
DIP SWITCH SETTING
OFF
VIM Disable
ON
Rear-View Camera Enable
OFF
N/A
OFF
Opon for GREEN Wire
OFF
CAN Terminaon Radio Side
ON
CAN Terminaon Car Side
The parking lines are there to assist you while reversing. To acvate the parking lines simply cut/disconnect the
WHITE loop wire located near the 4 pin camera connector.
What the Lines mean:
Green Line: CLEAR
Yellow Line: GETTING CLOSE
Red Line: WARNING - VERY CLOSE
White Line: SHOWS THE PATH DIRECTION
VES will be your source for the AV Input.
To access the VES buon, press the RADIO/MEDIA buon on the le side of the radio. The VES buon is only
acve aer the interface is properly installed.
JEEP
2007 2017 WRANGLER
MyGig Radio
Rev.0926 17
3 / 3


Specyfikacje produktu

Marka: CRUX
Kategoria: Niesklasyfikowane
Model: RVCCH-75WM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CRUX RVCCH-75WM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane CRUX

CRUX

CRUX DKGM-16B Instrukcja

3 Stycznia 2025
CRUX

CRUX ACPBM-77Y Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPMB-45W Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPLX-12XW Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPBM-77X Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPAD-01 Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPAD-81Y Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPBM-77Z Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPMB-50W Instrukcja

1 Stycznia 2025
CRUX

CRUX ACPLR-01 Instrukcja

1 Stycznia 2025

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane