Instrukcja obsługi CRUX RVCCH-75E

CRUX Niesklasyfikowane RVCCH-75E

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CRUX RVCCH-75E (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
RVCCH-75E
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020520
1 of 4
• Acvates Uconnect Touchscreen Radio for enabling Video features
• Aermarket Rear-view Camera included
• Automacally switches to Rear-view when car is in Reverse mode
• Forced reverse camera view feature
• VIM funcon
• Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75E Module RVCCH-75E Harness
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
DP
ON
DIP
SWITCH
LED* *LED RED = Power ON Status
LED BLUE = Data Bus ON Status
Regulator
20 Ft. Coax Cable
8-Pin Molex
Represents Solder Joint
TO RADIO
WHITE
22-PIN
(MALE)
GRAY
22-PIN
(MALE)
WHITE
22-PIN
(FEMALE)
GRAY
22-PIN
(FEMALE)
TO FACTORY
HARNESS
GREEN WIRE
ACTIVATE VIDEO BYPASS
WHITE Wire*
(Camera Power Output
+12V 250mA)
RED Wire
Tape O
(Not Used)
CUB-01 Camera
Included
*White wire does not supply Reverse Trigger on Manual Transmissions.
Camera power must be connected to factory reverse light wire instead.
To Source Ground
(ground wire)
(not chassis ground)
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020520
2 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE BULLET CAMERA AND CABLE
The kit includes a universal bullet camera that can be mounted in dierent ways. On way is to mount it on the
third brake light. Please see page 3 for installaon instrucons. Once the camera has been installed, route the
camera cable towards the radio.
INSTALLING THE RVCCH-75E MODULE
Remove the radio to gain access to the connectors. Unplug the factory WHITE and GRAY connectors and plug
them into the WHITE and GRAY connectors of the RVCCH-75E T-harness. Mate the YELLOW male and female
video RCAs of the RVCCH-75E T-harness and the camera cable. Use the thin RED wire on the camera cable to
power the camera. Connect the thin RED wire to the WHITE wire on the RVCCH-75E harness. The RED wire near
the camera is not used and needs to be insulated with tape. Connect the BLACK ground wire near the camera to
chassis ground. See diagram on page 1. Test the system for funconality before reinstalling the radio.
FORCED VIEW OF REVERSE CAMERA
The RVCCH-75E has a feature that allows the user to view the reverse camera while driving.
To acvate this feature, set DIP#4 to ON. Press and hold the middle buon on the le side
SWC behind the steering wheel for 2-3 seconds. Press it again to deacvate this feature.
The camera is defaulted to power o aer 10 seconds.
DIP SWITCH FUNCTIONS:
DIP 1 = Video in Moon Acvaon ON / OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Not Used
DIP 4 = Forced RVC ON / OFF
DIP 5 = Camera/ParkAssist Coding (see page 5)
DIP 6 = Varies - Defaulted to both OFF*
RVCCH-75E
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020520
3 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75E
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
1. Remove the third brake light assembly. Use the supplied
drill saw and drill a hole on the back side of the third brake
light housing.
2. Connue drilling unl the pilot drill bit is visible on the
front side of the third brake light.
3. Turn over the third brake light assembly start drilling from
the front side. Carefully drill thru the red plasc lens.
4. Insert the camera cable and the camera thru the hole
but DO NOT FULLY INSERT. This will allow you to rotate the
camera to the right posion. Turn the ignion key to ON but
do not start the engine. Put the gear in reverse and check
the camera view. Adjust as necessary.
6. The CUB-01 bullet camera has parking guide lines that
can be turned ON or OFF. The parking guide line is defaulted
to ON from the factory. To turn OFF the parking guide lines,
cut the thin WHITE wire on the camera cable around 4 feet
away from the camera. Insulate with tape. Unplug the 4-pin
barrel connector near the thin WHITE wire. Align the arrows
on the 4 pin barrel connector and plug them together.
Make sure that the connectors are plugged in all the way.
5. Route the camera cable towards the radio/RVCCH-75E
locaon.

Specyfikacje produktu

Marka: CRUX
Kategoria: Niesklasyfikowane
Model: RVCCH-75E

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CRUX RVCCH-75E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane CRUX

CRUX

CRUX SOOGM-16 Instrukcja

8 Października 2024
CRUX

CRUX DKGM-16W Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52B Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52 Instrukcja

8 Października 2024
CRUX

CRUX ACP-MAX Instrukcja

8 Października 2024
CRUX

CRUX RFM-MG1 Instrukcja

8 Października 2024
CRUX

CRUX SOCGM-18L Instrukcja

8 Października 2024
CRUX

CRUX SWRGM-49L Instrukcja

8 Października 2024
CRUX

CRUX WVICH-03M Instrukcja

8 Października 2024
CRUX

CRUX WVIFD-02F Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024