Instrukcja obsługi CRUX CS-CR41

CRUX Niesklasyfikowane CS-CR41

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CRUX CS-CR41 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
RADIO REPL ACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030520
CS-CR41
Radio Replacement with SWC Retention for
CHRYSLER, DODGE and JEEP Vehicles
1 of 3
PRODUCT FEATURES:
NOTES:
PARTS INCLUDED:
- Retains factory features in select Chrysler, Dodge and Jeep vehicles while funconing with an aermarket radio.
- Retains Steering Wheel Controls via built-in, pre-programmed interface.
- Supports amplied and non-amplied systems.
- Provides reverse trigger for rear view camera.
- EIA color coded wiring for easy installaon.
1. The Front and Rear fading are NON-Adjustable on amplied systems.
2. Also supports radio replacement in vehicles with 4.3” and 8.4” color screens.
3. Does not retain Uconnect.
CS-CR41 MODULE Audio Filter1st Gen Harness 2nd Gen Harness SWC Cables
INSTALLATION DIAGRAM:
The CS-CR41 includes 2 harnesses for older and new model vehicles. Only 1 of the harness connectors
will t into your radio. See installaon diagrams below for each harness.
1st Generaon Harness
TO FACTORY
HARNESS
12-Pin Black
Connector
First Generation Harness
*Does not supply Reverse Trigger on Manual Transmissions. Reverse trigger wire from the
aftermarket radio and/or camera power must be connected to factory reverse light wire instead.
1 2 3
ON
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW Insulate with tape
if not being used
3.5MM SWC CABLES (Option A or B)
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
AFTERMARKET
RADIO
VSS (Vehicle Speed Sense) Pink
Illumina�on (+) Orange
Power Antenna/Amp Turn on Blue/ White
Reverse Trigger* Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
AMPLIFIED
NON AMPLIFIED
See page 2 for
speaker wire
connections
Audio
Filter
RADIO REPL ACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030520
CS-CR41
Radio Replacement with SWC Retention for
CHRYSLER, DODGE and JEEP Vehicles
2 of 3
AFTERMARKET
RADIO
TO FACTORY
HARNESS
12-Pin Black
Connector
Second Generation Harness
*Does not supply Reverse Trigger on Manual Transmissions. Reverse trigger wire from the
aftermarket radio and/or camera power must be connected to factory reverse light wire instead.
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW Insulate with tape
if not being used
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
1 2 3
ON
VSS (Vehicle Speed Sense) Pink
Illumina�on (+) Orange
Power Antenna/Amp Trun on Blue/ White
Reverse Trigger* Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
AMPLIFIED
NON AMPLIFIED
See below for
speaker wire
connections Audio
Filter
2nd Generaon Harness
NON AMPLIFIED SYSTEMS AMPLIFIED SYSTEMS
Plug the 4-pin Molex connector to the NON-AMPLIFIED
side of the inline lter.
Plug the 4-pin Molex connector to the AMPLIFIED
side of the inline lter.
Wire Connecons: Wire Connecons:
Aermarket Radio CS-CR41 Harness Aermarket Radio CS-CR41 Harness
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Green
Green/Black
Purple
Purple/Black
Not Used
Not Used
Not Used
Not Used
Speaker wire connecons:
Wire the audio lter using the connecon chart below. Plug the 4 pin Molex plug found on the 1st and 2nd
generaon harnesses to the corresponding 4 pin Molex socket on the audio lter. (Amplied or Non-Amplied)
RADIO REPL ACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.030520
CS-CR41
Radio Replacement with SWC Retention for
CHRYSLER, DODGE and JEEP Vehicles
3 of 3
DIP SWITCH SETTINGS:
VEHICLE APPLICATIONS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP#: 1 2 3
Atoto, Dual, Fahrenheit, Jensen
Pioneer, Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radio
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF ON ON
OFF ON ON
OFF ON ON
OFF OFF OFF
ON ON OFF
ON ON ON
ON OFF ON
ON OFF OFF
OFF ON OFF
SWC MODULE
DIP SWITCH
1 2 3
ON
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
4-PIN SWC CABLE
Use the proper 3.5MM to 4-Pin SWC cable for the aermarket radio you are using.
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is aached)
OPTION B is used for ATOTO, BLAUPUNKT, BOSS, DUAL, FARENHEIT, JENSEN, POWER ACOUSTIK,
PIONEER, SONY, SOUNDSTREAM and Most O-Brand Radios.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires instead of a 3.5mm plug for SWC connecon, cut o the 3.5mm plug on the Crux SWC
Cable (opon B) and connect the SWC wires as follows:
Note that there are some radios that only have
SWC1 and SWC2, in this case “shield” does not
need to be connected.
CHRYSLER
2011-2014 200
2005-2010 300
2007-2009 Aspen
2006-2010 PT Cruiser
2007-2010 Sebring
2008-2016 Town & Country
DODGE
2007-2014 Avenger
2006-2012 Caliber
2008-2014 Challenger
2006-2010 Charger
2013 Charger
2006-2011 Dakota
2004-2013 Durango
2009-2016 Grand Caravan
2009-2010 Journey
2013 Journey
2005-2008 Magnum
2007-2011 Nitro
2006-2012 RAM
JEEP
2006-2010 Commander
2007-2016 Compass
2005-2013 Grand Cherokee
2008-2012 Liberty
2007-2017 Patriot
2007-2017 Wrangler
MITSUBISHI
2006-2009 Raider
VOLKSWAGEN
2009-2013 Routan

Specyfikacje produktu

Marka: CRUX
Kategoria: Niesklasyfikowane
Model: CS-CR41

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CRUX CS-CR41, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane CRUX

CRUX

CRUX SOOGM-16 Instrukcja

8 Października 2024
CRUX

CRUX DKGM-16W Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52B Instrukcja

8 Października 2024
CRUX

CRUX DKVW-52 Instrukcja

8 Października 2024
CRUX

CRUX ACP-MAX Instrukcja

8 Października 2024
CRUX

CRUX RFM-MG1 Instrukcja

8 Października 2024
CRUX

CRUX SOCGM-18L Instrukcja

8 Października 2024
CRUX

CRUX SWRGM-49L Instrukcja

8 Października 2024
CRUX

CRUX WVICH-03M Instrukcja

8 Października 2024
CRUX

CRUX WVIFD-02F Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024