Instrukcja obsługi Crestron Saros ICE8T-W-T-EACH

Crestron głośnik Saros ICE8T-W-T-EACH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron Saros ICE8T-W-T-EACH (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Saros® Express 2-Way In-Ceiling Speakers
quickstart guide
SAROS_ICE4T/ICE6T/ICE8T
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
SAROS_ICE4T/ICE6T/ICE8T
Set the Transformer Tap Selector Switch
The speakers are equipped with a 70/100 V matching transformer for distributed audio
systems. The transformer tap selector switch on the front panel is used to set the speaker
power level. Use a flat blade screwdriver to adjust the switch.
1. For SAROS_ICE4T and SAROS_ICE6T 70 V systems, use the left side settings and
select from 3.75, 7.5, 15, or watts. 30
2. For SAROS_ICE4T and SAROS_ICE6T 100 V systems, use the right side settings
and select from position should not be used.7.5, 15, or 30 watts. The X
3. For SAROS_ICE8T 70 V systems, use the left side settings and select from 7.5, 15,
30, or 60 watts.
4. For SAROS_ICE8T 100 V systems, use the right side settings and select from 15 30, ,
or 60 watts. The X position should not be used.
The switch may also be set to operation, bypassing the transformer completely. This 8Ω
setting should be used only for 8 Ω audio systems.
QUICKSTART DOC. 7496A (2037419) 11.13
1
1Installation
Saros® Express speakers by Crestron® deliver easy
installation and excellent performance in a range of
popular sizes for cost-sensitive commercial applications.
Ideal for use in background music, paging, and sound
reinforcement systems, Saros Express speakers are
engineered to achieve full, even coverage and clear
sound quality at a very affordable cost. Their zero-
bezel frameless grille achieves an unobtrusive and
contemporary appearance. Installing the grille requires
no hardware or tools, utilizing powerful magnets to hold
it in place. A safety tether is included to prevent the grille
from ever falling from the ceiling.
Saros Express speakers are available in white or black
and can be painted to blend with the ceiling surface.
Prepare Mounting Hole
Front View - Grille Removed
Tighten
Screws
70V 100V
IN
THRU
Terminal Block
Not Shown
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. If applicable, use a good quality stud finder to
locate joists. If there are no obstructions, use the supplied template to trace an outline of
the mounting hole.
For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the
mounting hole. For drywall or standard construction ceilings, use the template to trace the
mounting hole directly on the ceiling.
Install Cable
Run the cable from the audio source to the speaker location, observing all appropriate
local codes. Strip the ends of the speaker cables approximately 1/8” to 3/16” (~3 mm to
~5 mm) and twist the strands.
Install Tile Bridge
The included tile bridge components provide proper support when the speaker is installed
in a typical drop tile ceiling. Refer to the illustration below.
1. Based on the location of the mounting hole determined in “Prepare Mounting Hole”
above, use the two supplied screws to attach the support ring to the rails so that
when installed, the ring is aligned with the mounting hole and the rails rest on the
ceiling grid frame.
2. The support ring position on the rails is adjustable to enable off-center speaker
positioning. The tile bridge assembly can be folded to fit through the speaker cutout in
blind-mount situations.
Speaker Cable Connections
Screw
Cable
Clamp
Speaker
Cable
Terminal
Block
Mounting
Clips
Rear
Cover
Panel
Mount/Remove Speaker
The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is mounted
on the speaker, remove it before proceeding. (Refer to “Install/Remove Grille” above.)
1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift the
cover panel off to expose the supplied terminal block.
2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal block,
using the outer terminals: red to and black to . Use the inner and terminals to connect a IN + – + – THRU
pass-through (parallel) speaker.
3. Allow some slack in the speaker cable(s) and position the cover panel on the back, making certain it
engages the mounting clips. Secure the cover panel using the screw removed in step 1 and tighten the
cable clamp to secure the cable(s). Do not overtighten. Use a safety tether attached to the rear enclosure
to prevent the speaker from accidentally falling.
4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up to
2.4 inches (61 mm). For extra thick tiles, reset the toggle clamps to the upper position before continuing.
a. With the toggle clamps turned inward, insert the speaker into the opening.
b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the speaker.
The toggle clamps first rotate into clamping position (as indicated in the front view illustration to the
right) and then begin holding the speaker to the ceiling.
c. Tighten the screws until the speaker is secure. Do not over tighten.
5. Speaker removal is accomplished by reversing steps 1 through 4 above.
Tile Bridge Assembly
Install/Remove Grille
The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to prevent
any possibility of the grille falling from the ceiling. With the tether attached, place the grille in position on
the speaker. To remove the grille, grip the edges and pull away from the speaker.
Paint the Speaker Grille
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grille and set it aside for reinstallation. It may be
necessary to use a knife or other sharp instrument to free an edge of the material so it can be peeled
away. Use care to avoid cutting or tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in the grille.
3. Once the paint is dry, reinstall the material to the underside.
Safety Tether
Rigging Points
For SAROS_ICE8T
100V70V
For SAROS_ICE4T,
and SAROS_ICE6T
100V70V
20.91 in
(531 mm)
Support
Ring
Screws
(Supplied)
25.92 in
659 mm
QUICKSTART DOC. 7496A (2037419) 11.13
Saros® Express 2-Way In-Ceiling Speakers
quickstart guide
SAROS_ICE4T/ICE6T/ICE8T
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
SAROS_ICE4T/ICE6T/ICE8T
The specific patents that cover crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Saros are either trademarks or registered trademarks of Crestron
Electronics, Inc., in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in the marks
and names of others. Crestron is not responsible for errors in typography or photography.
This document was writtren by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
3Specifications
2
SPECIFICATION
SAROS_ICE4T/ICE6T/ICE8T
SAROS_ICE4T SAROS_ICE6T SAROS_ICE8T The following table provides corrective action for possible trouble situations. If
further assistance is required, please contact a Crestron customer service
representative.
Further Inquiries
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or,
for assistance within a particular geographic region, refer to the listing of Crestron
worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at
www.crestron.com/onlinehelp. First-time users must establish a user account to
fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of
the SAROS_ICE4T/ICE6T/ICE8T, additional information may be made available as
manual updates. These updates are solely electronic and serve as intermediary
supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
TROUBLE
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
No sound or
intermittent
sound is
coming from
the speakers.
There is a cable connection
error.
Verify the cable connections
between the amplifier and
speakers.
The amplifier is not
receiving an input signal or
there is a malfunction.
Verify that the amplifier is
functioning correctly, that it is
receiving an input signal, and
that the correct input source
is selected.
There is a faulty device in
the system.
Verify that all system devices
are functioning properly.
Constant noise
such as buzz,
hum, or hiss is
coming from
the speakers.
There is a system grounding
fault.
Verify that system grounding is
correct.
Low frequency
output is poor.
There is an incorrect
polarity connection at the
speaker or amplifier.
Verify the speaker connection
polarity ( on + on amplifier to +
speaker).
4Problem Solving
Troubleshooting
2Physical Views
Rear and Side View (Typical)
Construction
Enclosure Zinc-plated steel, plenum-rated, 1/2 in or 3/4 in conduit knockout top and side, 1 cable
clamp included
Baffle ABS UL94V-0 plastic
Grille Steel with textured finish, paintable, magnetically-held zero-bezel frameless,
safety tether
Mounting Flush ceiling mount using 4 integral 2-step toggle clamps, 2.4 in (61 mm) maximum
surface thickness, tile bridge included; (2) Rigging points for safety tether
(SPKA-ST-15 sold separately)
IN
T HRU
Recommended
Cutout Diameter
Diameter
Minimum
Mounting Depth
Front View - Grille Removed (Typical)
8.53 in (217 mm) not
including toggles
7.13 in (181 mm)
7.70 in (195 mm)
6.90 in (176 mm)
7.0 lb (3.2 kg)
10.57 in (269 mm) not
including toggles
8.31 in (211 mm)
9.70 in (245 mm)
8.10 in (206 mm)
10.0 lb (4.5 kg)
12.07 in (307 mm) not
including toggles
9.10 in (231 mm)
11.20 in (285 mm)
8.90 in (226 mm)
12.2 lb (5.7 kg)
Dimensions
Diameter
Depth
Recommended
cutout diameter
Minimum mounting
depth
Weight
Connections
Input (1) 4-pin 5 mm detachable terminal block with screw-down flanges;
Speaker input with parallel pass-through;
Maximum Wire Size: 12 AWG
Controls
Transformer Tap (1) Recessed, 5-position, screwdriver adjustable, rotary switch on baffle;
Used to select 70/100 V tap settings or 8Ω (bypass)
Environmental
Temperature -2° to 120° F (-19° to 49° C)
Humidity 5% to 95% RH (non-condensing)
100V70V
8.0 in (203 mm)
treated paper with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) treated
cloth dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
7.5, 15, 30, 60 watts at
70 V; 15, 30, 60 watts at
100 V
70 Hz to 20 kHz (±3 dB)
55 Hz to 20 kHz (-10 dB)
75 watts program, (8 Ω)
89 dB @ (W/m)
95° conical (nominal)
6.5 in (165 mm)
treated paper with ring
mode decoupled cloth
surround and steel basket
0.98 in (25 mm) treated
cloth dome, horn-loaded
2.5 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30 watts at
70 V; 7.5, 15, 30 watts at
100 V
75 Hz to 20 kHz (±3 dB)
60 Hz to 20 kHz (-10 dB)
60 watts program (8 Ω)
89 dB @ (W/m)
95° conical (nominal)
4.0 in (102 mm)
treated paper with ring
mode decoupled cloth
surround and steel basket
0.79 in (20 mm) treated
cloth dome, horn-loaded
2.0 kHz
8 Ω nominal with
transformer set to 8Ω
3.75, 7.5, 15, 30 watts at
70 V; 7.5, 15, 30 watts at
100 V
85 Hz to 20 kHz (±3 dB)
75 Hz to 20 kHz (-10 dB)
40 watts program, (8 Ω)
89 dB @ (W/m)
95° conical (nominal)
Woofer
Tweeter
Crossover Frequency
Impedance
Transformer Taps
Frequency Response
Frequency Range
Power Handling
Sensitivity
Coverage

Specyfikacje produktu

Marka: Crestron
Kategoria: głośnik
Model: Saros ICE8T-W-T-EACH

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Crestron Saros ICE8T-W-T-EACH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Crestron

Crestron

Crestron ULTIMATE IC3-SA-WOOFER Instrukcja

30 Września 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-BOX-WOOFER Instrukcja

30 Września 2024
Crestron

Crestron ULTIMATE IC3-AW-SA-TWEETER Instrukcja

30 Września 2024
Crestron

Crestron ULTIMATE IWS82-AW-W-T-EACH Instrukcja

27 Września 2024
Crestron

Crestron ULTIMATE IWLCR62-W-T-EACH Instrukcja

27 Września 2024
Crestron

Crestron SAROS IC8T-W-T-EACH Instrukcja

26 Września 2024
Crestron

Crestron ULTIMATE ASUB10-B-T-EACH Instrukcja

24 Września 2024
Crestron

Crestron Excite IW6 Instrukcja

23 Września 2024
Crestron

Crestron Essence IW5-W-T Instrukcja

22 Września 2024
Crestron

Crestron SAROS IC6T-W Instrukcja

22 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024