Instrukcja obsługi Crestron BPCI-8


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crestron BPCI-8 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
DO GUIDE
1. Remove the faceplate by snapping it off the button assembly.
NOTE: Use care when removing the faceplate, as it holds the button support grid and
button caps in place.
2. Ensure the button unit is oriented with the arrow at the top, and then insert the unit into the
electrical box and attach it using the supplied #6-32 x 1" screws.
3. Return the button caps to their original positions on the button assembly with LED windows
oriented upward to match each LED indicator.
4. Install the button support grid with stabilizing tabs to the rear, put the faceplate in position
(optical cable access port on the lower right), and snap it into place.
Mount the BPC-8-IMC
Mount the BPC-8-IMC onto an appropriate surface at the display location using the supplied
hook and loop tape.
DO Connect the Device
Make connections to the BPC-8 using Crestron® power supplies for Crestron equipment. Apply
power after all connections have been made.
Connect the BPC-8
BPC(I)-8
onCue® Basic Presentation Controller
DO Install the Device
NOTE: The BPC-8 and BPCI-8 are functionally similar. For simplicity within this guide, the term
“BPC-8” is used except where noted.
The hardware supplied with the BPC-8 is listed in the DO Check the Box table.
The following tools are required for installation of a BPC-8:
1. Phillips screwdriver (not included)
2. Two #6-32 x 1" pan head Phillips screws (included)
3. Two 4-pin detachable terminal block connectors (included)
Install a Conductor Cable
Install a 4-conductor cable (minimum 24 AWG) with 50ft (~15m) maximum length (not included)
between a 1-gang electrical box for the BPC-8 and the location of the BMP-8-IMC interface
module.
Refer to the pin connections shown in the installation diagram below and connect the supplied
4-pin detachable connectors to each end of the cable.
Mount the BPC-8 into an Electrical Box
Connect the preinstalled cable to the 4-pin terminal block on the rear of the button assembly,
and then mount the BPC-8 to a 1-gang electrical box as shown in the following diagram.
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1 Button Assembly 4512112
1 Module, Interface 4511874
1 Emitter Probe, IR, Crestron STRIP Black 2001137
1 Fastener, Dual Lock, 2.5" x 1" 2005414
2 Connector, 4-Pin 2003576
2 Screw, 6-32 x 1", Pan Head, Phillips 2007251
BPC-8 Only
1 Power Pack, 12 Vdc 0.5 A, 100-240 Vac 2045853
BPCI-8 Only
1 Power Pack, 12 Vdc 0.5 A, 120-240 Vac 2045884
1 Bracket, Mounting, Single Gang 2030802
LED window
Button assembly
1-gang electrical box
(2.5 in (~63 mm) depth
recommended)
Interchangeable
button caps
Button support
grid
6-32x1”
pan head screws
Optical cable access port
CBL-PWR-CTRL-P-TL-50
cable or equivalent
Grid stabilizing tabs
LED
indicators
BPC- 8-IMC
12 T R G
12: Power (12 Vdc)
T: Data
R : Data
G: Ground
Faceplate
B PC-8-IMC
12 T R G
Access port: For optical cable from BPC-HLPIR
IR learner and programmer (optional)
BPC-8-IMC:Power and control signals to/from
BPC-8-IMC interface module (included)
DO GUIDE DOC. 7194A (2031223) 09.16
Specications subject t o change without not ice.
Connect the BPC-8-IMC
1. Connect the preinstalled cable to the 4-pin terminal block connector, and then connect the
IR emitter probe(s) or the RS-232 cable (not included), as needed, to the BPC-8-IMC.
2. Connect the power pack to AC power and to the BPC-8-IMC.
WARNING: Incorrect wiring may damage the BPC-8. The 4-pin detachable connectors should
not be connected to a Cresnet® network or any Cresnet devices.
DO Congure the Device
The BPC-8 supports custom software conguration les and interchangeable button caps for
various presentation control applications. For more information on conguring and operating the
BPC-8, refer to the BPC(I)-8 Supplemental Guide (Doc. 7100) at www.crestron.com/manuals.
DO Learn More
Visit the website for additional information and the latestrmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents t hat cover Crestron products are listed at . The product warrant y can be found at .
http://www.crestron.com/legal/patents www.crestron.com/warranty
Cert ain Crestron products contain open source sof t ware. For specic information, please visit . www.crestron.com/opensource
Crest ron, t he Crestron logo, Cresnet, and onCue are either trademarks or regist ered trademarks of Crestron Elect ronics, Inc. in the Unit ed States and/or other countries. Other trademarks,
registered t rademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any propriet ary interest
in the marks and names of others. Crest ron is not responsible for errors in t ypography or photography.
This document was written by the Technical Publications department at Crest ron.
©2016 Crestron Electronics, Inc.
IR OU T
12 3 C O M
B PC12 V
0.5 A G R T 12
12 Vdc @ 0.5 A:
From power pack
(included)
BPC: Power and
control interface with
BPC-8 controller
IR OUT:
Via IR probe to
any IR controlled
media device
COM:
1-way RS-232 to
media device


Specyfikacje produktu

Marka: Crestron
Kategoria: nieskategoryzowany
Model: BPCI-8

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Crestron BPCI-8, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Crestron

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024