Instrukcja obsługi Crest Audio Versarray 112 MKIII

Crest Audio głośnik Versarray 112 MKIII

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crest Audio Versarray 112 MKIII (32 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
1
Versarray™ 112 Mk III
Passive Enclosure
Product Specifications
e Versarray™ 112 Mk III Passive Ribbon Tweeter Line Source Array speaker system consists of a 12” Neo Black
Widow® woofer combined with a Neodymium based Peavey RD™ 2.6 Mk III ribbon tweeter in a cabinet with a
simple, quick, yetexible rigging system. Designed to provide modular coverage of small to medium venues,
and intended for use with the companion Versarray™ Mk III Sub models, the Versarray™ 112 Mk III oers ex-
cellent versatility with a very high performance capability. e two-way system consists of the following driver
components: a 12” Black Widow® Neo series woofer with Neodymium magnet structure. Capable of over 500W
of continuous power handling (AES Std 2-1984), the woofer can handle a lot of sheer power.e high frequen-
cies are handled by two Peavey® RD™ 2.6 Mk3 ribbon tweeters utilizing a composite sandwich ribbon, a Neo-
dymium magnet system, and a low distortion CLEAR FORM™ waveguide.
Designed to be used in conjunction with a compatible DSP based loudspeaker signal processor, such as a Peavey
Digitool™, Nion® or MediaMatrix® system, with the Peavey factory settings in use, the Versarray™ 112 Mk III can
perform to modern standards of excellence, and handily exceed the competitions audible performance.
e FlyQWIK™ fully articulated hardware rigging system provides for a classic straight line-array conguration,
or a number of dierent angling options, providing easy aiming of the system. Angles between the array modules
is adjustable from 0 degrees (straight), to 15 degrees in 2.5 degree increments. Total angle possible between two
cabinets is 15 degrees.
Quick-lock pins are supplied with the rigging hardware to couple the Versarray™ 112 Mk III modules together
and lock the angles between them into place, as well as for the rigging halo and y bar congurations of a line
array. e exibility of the Versarray™ system allows the use of anywhere from 1 to 10 Versarray™ 112 Mk III
modules in conjunction with Versarray™ 218 Mk III Subs. An optional special groundstack bracket set mounts
to the Versarray 218 Mk III Sub, and allows up to three of the Versarray™ 112 Mk III ‘s to be mounted on top of
the Versarray 218 Mk III Sub, and angled upward, for use on stage in a stadium seating situation.
Features
• 2-way Bi-Amp Ribbon Line Source Array SR System
• 12” Neo Black Widow® 4” VC Woofer
• 1000 watt program, 2000 watt peak power handling
• Ribbon Tweeters with Neo magnet and composite material sandwich ribbon
• Ribbon Tweeters mounted to our proprietary CLEAR FORM™ Waveguide
• 90 H by 15 V degree coverage pattern (per one cabinet)
• Easy aiming FlyQWIK™ hardware rigging system
• Angle adjustable in 2 1/2 degree increments, from 0 to 15 degrees total angle between adjacent cabinets
• Sound Guard™ tweeter protection, series capacitor for reliability
• Inputs are two Neutrik® Speakon® 4 pin jacks in parallel
• 18 mm 13 ply Baltic Birch enclosure with steel inner brackets
• Injection molded cabinet end caps, made from high impact material.
• Hammerhead™ polyurea black nish and black powder-coated cloth lined grilles
2
Frequency Response, 1 meter on-axis,
swept-sine in anechoic environment:
100 Hz to 20 kHz (±3 dB, with
processing)
Usable Low Frequency limit, -10 dB
point: 85 Hz (with processing)
Power Handling:
Low Frequency Section: 500 W
continuous 1,000 W program 2,000 W
peak
High Frequency Section: 120 W
continuous 240 W program 480 W
peak
Sound Pressure Level, 1 Watt, 1 meter
in anechoic environment:
Low Frequency Section: 97 dB SPL,
(2.83 V input)
High Frequency Section: 101 dB SPL,
(4.0 V input for 16 ohm wiring)
Maximum Sound Pressure Level (1
meter) * :
Low Frequency Section: 124 dB SPL
continuous 130 dB SPL peak
High Frequency Section: 122 dB SPL
continuous 128 dB SPL peak
*Note: This spec is for one module at 1
meter, a line array of 6 units has much
higher output at distance due to line
source effect where SPL falls off at 3 dB
per distance doubling rather than 6 dB
Nominal Radiation Angle measured
at -6 dB point of polar response: 90
degrees Horizontal by 15 degrees
Vertical (One module only, straight line
array of more than 1 module narrows
vertical dispersion accordingly)
Transducer Complement:
Low Frequency Section: 1x 12 in.
Woofer, 1244 Neo Black Widow® 4” VC
Woofer, in a sealed box
High Frequency Section: 2x 4.75
in. Ribbon Tweeters Two RD™ 2.6
Mk III Peavey Ribbon Tweeters, on a
waveguide
Box Tuning Frequency (Sealed): Low
Frequency Section: 88 Hz
Electroacoustic Crossover Point, Peavey
Active Digital Crossover:
(Applies to VSX™, Digitool® and Nion®/
MediaMatrix® settings provided by
Peavey)
Sub – Low Frequency: 125 Hz at 24dB/
octave
Low Frequency – High Frequency:
1950 Hz at 24dB/octave
Recommended Active Crossover
Frequency Region and Slope: Sub –Low
Frequency: 125 Hz at 24dB/octave LR
Low Frequency –High Frequency: 2000
Hz at 24dB/octave LR
Impedance (Z):
Low Frequency: Nominal: 8.0 Ohms,
Minimum: 6.5 Ohms
High Frequency: Nominal: 16 Ohms,
Minimum: 13.6 Ohms
(Special Note: Ribbon tweeters
are capacitor coupled so use with
switching amps is allowed.)
Input Connections: 2x Neutrik® 4-pin
Speakon® jack
Enclosure Materials & Finish: 18 mm
13 ply Baltic Birch plywood finished
in a tough Hammerhead™ polyurea
black finish, with injection molded
end caps and horn, with a perforated
steel grille finished in black powder
coat paint and a cloth liner inside.
Inner steel frame and backing plates
for rigging hardware.
Mounting provisions: Custom array
brackets and hardware, and a custom
array angle adjustment system are
included with each module. Quick
release pins are included with each
cabinet.
Dimensions (H x W x D):
Front: 15.13 in. x 25.06 in. x 15.19 in.
384 mm x 637 mm x 386 mm
With Rigging hardware and Pins:
15.13 in. x 27.13 in. x 16.75 in.
321 mm x 689 mm x 426 mm
Net Weight: 66 Lbs. (30.0 kg)
{includes all cabinet associated
rigging hardware for each cabinet,
including quick-lock pins, etc.}
Companion Subwoofers (sold
separately): Versarray™ 218 Mk III
Sub double 18” Lo Max® woofer
subwoofer
Optional Accessories:
3 foot speaker cable, with 16 gauge 4
conductor wires with 4-pin to 4-pin
Neutrik plugs (Peavey part number
00585240); and 10mm Quick Release
Positive Lock Pins for array rigging.
Flying/Rigging Options:
Versarray™ Mk III HALO
Versarray™ Mk III FLY BAR, 6FT
LENGTH
Versarray™ Mk III SUB SUPPORT
FRAME
Versarray™ Mk III FLY BAR, 2FT
LENGTH
SPECIFICATIONS Versarray
™
112 Mk III
3
Figure B Directivity Index
Frequency [Hz]
Level [dB]
Figure C Horizontal Beam Width
Frequency [Hz]
Angle Degree
Frequency [Hz]
Figure D Vertical Beam Width
Angle Degree
Frequency [Hz]
dB SPL
Figure A Frequency Response

Specyfikacje produktu

Marka: Crest Audio
Kategoria: głośnik
Model: Versarray 112 MKIII

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Crest Audio Versarray 112 MKIII, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Crest Audio

Crest Audio

Crest Audio CPL 10+ Instrukcja

14 Grudnia 2024
Crest Audio

Crest Audio CPL 6+ Instrukcja

10 Września 2024
Crest Audio

Crest Audio CPL 5C+ Instrukcja

7 Września 2024
Crest Audio

Crest Audio CPL 8T Instrukcja

3 Września 2024
Crest Audio

Crest Audio Versarray PRO 215 Instrukcja

2 Września 2024
Crest Audio

Crest Audio CPL 6T Instrukcja

1 Września 2024
Crest Audio

Crest Audio CPL 265B+ Instrukcja

31 Sierpnia 2024
Crest Audio

Crest Audio CPL 8+ Instrukcja

30 Sierpnia 2024
Crest Audio

Crest Audio Versarray 218 MKIII Instrukcja

30 Sierpnia 2024
Crest Audio

Crest Audio CPL 25C+ Instrukcja

29 Sierpnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

LD Systems

LD Systems STINGER G3 TMB Instrukcja

8 Kwietnia 2025
JBL

JBL Conceal C83 Instrukcja

8 Kwietnia 2025
JBL

JBL Control 426LP Instrukcja

8 Kwietnia 2025
Crestron

Crestron SAROS ICE4T Instrukcja

7 Kwietnia 2025
Crestron

Crestron SAROS ICI6T Instrukcja

7 Kwietnia 2025
Crestron

Crestron SAROS IC8T Instrukcja

7 Kwietnia 2025
Focal

Focal K2 Power M FRAK Instrukcja

5 Kwietnia 2025
Turbosound

Turbosound PQ12-SB Instrukcja

3 Kwietnia 2025
Trust

Trust Tytan GXT 658 Instrukcja

3 Kwietnia 2025
Turbosound

Turbosound PQ15-YB Instrukcja

3 Kwietnia 2025