Instrukcja obsługi Chief RSMA020

Chief Wsparcie dla płaskich paneli RSMA020

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief RSMA020 (16 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
I N S T A L L A T I O N I N S T R U C T I O N S
RSM Elite Series Projector Mounts
RPA Elite Series Projector Mount
RPA Elite Series Projector Mount
RPA Elite Series Projector Mount
RPA Elite Series Projector Mount
RPA Elite Series Projector Mount
RPA Elite Series Projector Mount
RSM A-D
RSM Elite Installation InstructionsSeries Projector Mounts
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the RSM does not exceed 25 lbs
(11.34 kg).
• The weight capacity of the RSM may be LIMITED to the
lowest weight capacity of any other components
located between the RSM and the supporting structure!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The RSM mounts are designed to be:
• mounted to a 1-1/2" NPT or NPSM following ANSI/
ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness aluminum- ASTM B221) threaded extension
column.
• mounted to double 2" x 4" wood stud cross bracing
(1-1/2" on center) between two 2" x 4" ceiling joists;
with a maximum drywall covering of 5/8".
• mounted to a concrete ceiling with a minimum
thickness of 8" and a maximum drywall covering of
5/8"; or
• suspended from four 1/4" diameter (minimum) Grade 2
or better threaded rods (not included) which are
secured to unistrut, angle or channel assembly
overhead structural members (trusses or I-beams) by
Grade 2 or better 1/4" channel nuts (not included).
--SAVE THESE INSTRUCTIONS--
Installation Instructions RSM Elite Series Projector Mounts
3
DIMENSIONS
5.07
128.7
1.83
46.4
ROLL ADJUSTMENT POINT
4
1.61
40.9
1.61
40.9
2.18
55.4
4.37
110.9
.22
5.6
2.28
BOLT CIRCLE
57.8
THREADS ONTO 1-1/2' NPT
YAW ADJUSTMENT POINT
10
PITCH ADJUSTMENT POINT
INTERFACE LOCKING SWITCH
NOTE: CUSTOM INTERAFCE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR PROJECTOR
WILL ADD DEPTH TO INSTALLATION AND
THE MOUNT.
SEE SSM-XXX DRAWING ALSO.

Specyfikacje produktu

Marka: Chief
Kategoria: Wsparcie dla płaskich paneli
Model: RSMA020

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief RSMA020, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Chief

Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief MFQUB Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024
Chief

Chief TPK1 Instrukcja

22 Września 2024
Chief

Chief PDR2612B Instrukcja

22 Września 2024
Chief

Chief CMA395 Instrukcja

22 Września 2024
Chief

Chief KTG225S Instrukcja

22 Września 2024
Chief

Chief MPWUB Instrukcja

22 Września 2024
Chief

Chief MCD6000 Instrukcja

22 Września 2024
Chief

Chief KRA202B Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

NEC

NEC PDVWXUN 55 P Instrukcja

15 Października 2024
Insignia

Insignia NS-STV3N1705 Instrukcja

15 Października 2024
One For All

One For All DM 4110 Instrukcja

9 Października 2024
One For All

One For All DM 7220 Instrukcja

9 Października 2024
One For All

One For All DM 2220 Instrukcja

9 Października 2024
Kogan

Kogan KASMM39S12A Instrukcja

9 Października 2024
Kogan

Kogan KATWM70TLMA Instrukcja

9 Października 2024
Kogan

Kogan KADMM46G24A Instrukcja

9 Października 2024
Kogan

Kogan KADMMPCGASC Instrukcja

9 Października 2024
One For All

One For All DM 2210 Instrukcja

9 Października 2024