Instrukcja obsługi Chief RPA297

Chief Wsparcie dla płaskich paneli RPA297

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief RPA297 (8 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
I N S T A L L A T I O N I N S T R U C T I O N S
Projector Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
RPA Series
RPA Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the RPA does not exceed 50 lbs
(22.7 kg).
• The weight capacity of the RPA may be LIMITED to the
lowest weight capacity of any other components
located between the RPA and the supporting structure!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The RPA mounts are designed to be:
• mounted to a 1-1/2" NPT or NPSM following ANSI/
ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness steel or aluminum - ASTM B221) threaded
extension column (not included); or
• mounted to a double 2" x 4" wood joist with a maximum
drywall covering of 5/8"; or
• suspended from four 1/4-20 Grade ASTM A307 or
better threaded rods (not included) which are secured
to unistrut by 1/4-20 Grade 2 or better channel nuts (not
included), or to angle or channel assembly overhead
structural members (trusses or I-beams) by 1/4-20
Grade 2 or better jam nuts (not included).
NOTE: RPA Series may be used with UL Listed models
WM210S, WM220S, WM230S, WM240S, WM210SI,
WM220SI, WM230SI and WM240SI (not included).
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
5.02
4.38
1.75
1 ½" NPT
5.50
3.25
4.50
5.50
3.75
BOLT CIRCLE
2.25
2.75
3.50
1.25
.75
ACCESS HOLE
STUDS ON SLB CENTER
IN THESE SLOTS
2.77
3.10
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR PROJECTOR
WILL ADD DEPTH TO INTALLATION AND
WILL AFFECT LOCATION OF PROJECTOR
ON MOUNT.
SEE SLB-XXXX DRAWING ALSO.
DIMENSIONS: INCHES
Installation Instructions RPA Series
3
LEGEND
TOOLS REQUIRED FOR INSTALLATION / PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Socket Wrench
Clé à douilles
Steckschlüssel
Chave de caixa
Chiave a brugola
Dopsleutel
Clé à douilles
A (1)
[RPA]
7/16"
1/8" (wood)
7/16"
B (1)
[Example of SLB bracket]
Hardware required - not included
(dependent on installation method)
1. Install to threaded extension column
• 1-1/2" NPT or NPSM following ANSI/ASME
B1.20.1 (Schedule 40, 0.154" minimum
thickness steel or aluminum - ASTM B221)
threaded extension column (not included)
2. Install to wood ceiling joists (Qty. of 4 each)
• 1/4" x 2" (minimum length) Grade 2 lag bolts
•1/4" Grade 2 nuts
• 1/4" Grade 2 washers
3. Install to threaded rod
• 1/4-20 steel threaded rods (Qty. 4)
• 1/4-20 Grade 2 channel nuts (Qty. 4)
• 1/4-20 Grade 2 jam nuts (Qty. 8)
• 1/4" Grade 2 washers (Qty. 8)
5/32"

Specyfikacje produktu

Marka: Chief
Kategoria: Wsparcie dla płaskich paneli
Model: RPA297

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief RPA297, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Chief

Chief

Chief TS218SU Instrukcja

9 Grudnia 2024
Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief MFQUB Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024
Chief

Chief K4G210B Instrukcja

23 Września 2024
Chief

Chief MF26000B Instrukcja

23 Września 2024
Chief

Chief FSB018BLK Instrukcja

23 Września 2024
Chief

Chief TPK1 Instrukcja

22 Września 2024
Chief

Chief PDR2612B Instrukcja

22 Września 2024
Chief

Chief CMA395 Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

Rocstor

Rocstor Y10N027-B1 Instrukcja

11 Grudnia 2024
StarTech.com

StarTech.com ARMQUADSS Instrukcja

10 Grudnia 2024
CTA Digital

CTA Digital ADD-AVPMB Instrukcja

10 Grudnia 2024
Gabor

Gabor FPC-85 Instrukcja

10 Grudnia 2024
Gabor

Gabor FPS-L Instrukcja

10 Grudnia 2024
Gabor

Gabor TM-UL Instrukcja

10 Grudnia 2024
Kanto

Kanto FMX2 Instrukcja

9 Grudnia 2024
Gabor

Gabor FSM-L Instrukcja

9 Grudnia 2024
Dell

Dell MDS19 Instrukcja

8 Grudnia 2024
Proaim

Proaim CT-SDCF-PRO Instrukcja

7 Grudnia 2024