Instrukcja obsługi Chief PAC117

Chief Wsparcie dla płaskich paneli PAC117

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief PAC117 (4 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
I N S T A L L A T I O N I N S T R U C T I O N S
Steel Stud / Dry Wall Anchor Kits
PAC115-116-117
PAC115-116-117 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components does not exceed 175 lbs (79.38 kg) or the
maximum weight capacity of the mount to which this
accessory is being installed. This product is NOT designed
for use with articulating wall mounts.
TOOLS/PARTS FOR INSTALLATION
(A)
[1/4-20 toggler anchor]
(B)
1/4-20 x 1-3/4"
(C)
1/4"
A B C
MODEL (qty) (qty) (qty)
PAC115 4 4 4
PAC116 8 8 8
PAC117 28 28 28
Installation Instructions PAC115-116-117
3
Assembly and Installation
1. Drill a 1/2" hole at the desired location, making sure wall is
at least 1/2" thick. If the wall is made with metal studs, it is
recommended to install the anchor through the drywall and
the metal stud.
2. Hold metal channel on anchor (A) flat alongside plastic
straps and slide channel through hole. (See Figure 1)
Figure 1
3. Holding plastic straps on anchor (A), pull anchor away from
wall until channel rests flush behind wall making sure anchor
channel is positioned vertically on stud. (See Figure 2)
4. Slide plastic cap on anchor (A) towards wall until flange of
cap is flush with wall. (See Figure 2)
Figure 2
5. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 3)
6. Repeat steps 1 through 5 for each mounting hole.
Figure 3
7. Place mount over anchors and align mounting holes in
display mount with holes in anchors. (See Figure 4)
8. Insert 1/4-20 x 1-3/4" Phillips pan head screws (B) through
1/4" washer (C), corresponding mounting hole on mount
and into anchor (A) and tighten until flush against mount.
DO NOT overtighten! (See Figure 4)
9. Repeat steps 7 and 8 for remaining mounting holes.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of
mounting hardware can damage the steel studs. DO NOT
overtighten mounting hardware!
Figure 4
(A)
Drywall
Plastic Straps
2
(A)
Plastic Cap
Drywall
Anchor Metal Channel
SIDE VIEW
3
Steel Stud
4
Plastic Straps
Drywall
Anchor Metal Channel
Plastic Cap
SIDE VIEW
5
Steel Stud
Drywall
Anchor Metal Channel
Mount
SIDE VIEW
(B)
8
Steel Stud
(C)

Specyfikacje produktu

Marka: Chief
Kategoria: Wsparcie dla płaskich paneli
Model: PAC117

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief PAC117, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Chief

Chief

Chief TS218SU Instrukcja

9 Grudnia 2024
Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief MFQUB Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024
Chief

Chief K4G210B Instrukcja

23 Września 2024
Chief

Chief MF26000B Instrukcja

23 Września 2024
Chief

Chief FSB018BLK Instrukcja

23 Września 2024
Chief

Chief TPK1 Instrukcja

22 Września 2024
Chief

Chief PDR2612B Instrukcja

22 Września 2024
Chief

Chief CMA395 Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

Rocstor

Rocstor Y10N027-B1 Instrukcja

11 Grudnia 2024
StarTech.com

StarTech.com ARMQUADSS Instrukcja

10 Grudnia 2024
CTA Digital

CTA Digital ADD-AVPMB Instrukcja

10 Grudnia 2024
Gabor

Gabor FPC-85 Instrukcja

10 Grudnia 2024
Gabor

Gabor FPS-L Instrukcja

10 Grudnia 2024
Gabor

Gabor TM-UL Instrukcja

10 Grudnia 2024
Kanto

Kanto FMX2 Instrukcja

9 Grudnia 2024
Gabor

Gabor FSM-L Instrukcja

9 Grudnia 2024
Dell

Dell MDS19 Instrukcja

8 Grudnia 2024
Proaim

Proaim CT-SDCF-PRO Instrukcja

7 Grudnia 2024