Instrukcja obsługi Chief MTR6000

Chief Wsparcie dla płaskich paneli MTR6000

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief MTR6000 (8 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
Chief Manufacturing, a products division of
Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
P: 800.582.6480 / 952.894.6280 F: 877.894.6918 / 952.894.6918
8805-000215 Rev 01
©2009 Milestone AV Technologies,
A Duchossois Group Company
02/09
I N S T A LL A T IO N IN S T R U C T IO N S
MEDIUM FLAT PANEL DISPLAY TILT MOUNT
MTR Series
The MTR Series tilt mount accommodates medium flat
panel displays weighing up to 125 lbs (56.70kgs).
The teardrop holes in the mount allow for quick
connect/disconnect of the display, thus simplifying
installation and maintenance processes.
The top and bottom mounting brackets are adaptable to
single wood stud mounting or dual wood studs that are
16” on center.
The display can be pulled and tilted into any position in
the zero-to-15 degree tilt range and remain stationary.
When fully retracted, the mount depth is 1.56 inches.
After installing the display on the mount, the screen can
be locked in place using the convenient latching flag.
A padlock can be used on the latching flag for added
security.
The mount is concealed behind the display, making it a
low profile wall mount.
! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation. OSHPD documents and drawings are available at
www.chiefmfg.com, and located on the product information page for the mount.
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and MTR, which could affect or void the Factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to the Warnings and Cautions in this document.
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
The maximum weight to be installed on the MTR Series tilt wall mount is 125 lbs (56.70kg).
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-6280.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
Installation Instructions MTR Series
2
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not
follow the instructions.
CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do
not follow the corresponding instructions.
WARNING Improper installation can result in serious personal injury! Make sure that the
structural members can support a redundant weight factor five times the total weight
of the equipment. If not, reinforce the structure before installing the MTR
WARNING Be aware of the potential for personal injury or damage to the equipment if it is not
installed correctly. Consider the weight of the mount without the display.
WARNING The installer is responsible for verifying that the display to which the wall mount is
fastened will safely support the combined load of all attached components or other
equipment.
WARNING The combined weight of the display placed on the wall mount must not exceed 125 lbs
(56.70 Kg),the maximum support weight of the MTR.
WARNING Watch for pinch points. Do not put your fingers between movable parts.
WARNING Make sure the flag securing the display is completely lowered at all times except when
removing or installing the display. The flag must be all the way down when
installing/removing cables.
CAUTION Check the unit for shipping damage before you begin the installation.
DIMENSIONAL DRAWING
Installation Instructions MTR Series
3
CONTENTS
DIMENSIONAL DRAWING ..................................... 2
TOOLS REQUIRED FOR INSTALLATION.............. 3
PARTS LIST .............................................................. 3
MTR INSTALLATION .............................................. 4
Select Mounting Location........................................ 4
Mount the MTR....................................................... 5
ATTACH MSB TO THE DISPLAY ........................... 6
INSTALL THE DISPLAY.......................................... 6
TILT ADJUSTMENT ................................................. 7
REMOVE THE DISPLAY.......................................... 7
TOOLS REQUIRED FOR
INSTALLATION
Drill and drill bit set
Wrench set
NOTE: Other tools may be required depending on your
method of installation.
Figure 1. Parts
PARTS LIST
Prior to assembly, unpack the carton completely. Verify
contents listed in Table 1 and Figure 1.
Read installation instructions completely. If you are
missing any of the listed parts, contact Customer Service.
Table 1. Parts List
REF DESCRIPTION QTY
10 MTR-Series Tilt Mount 1
— Lag Bolts 4
— Flat Washers 4
10
4 Lag Bolts
4 Washers

Specyfikacje produktu

Marka: Chief
Kategoria: Wsparcie dla płaskich paneli
Model: MTR6000

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief MTR6000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Chief

Chief

Chief TS218SU Instrukcja

9 Grudnia 2024
Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief MFQUB Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024
Chief

Chief K4G210B Instrukcja

23 Września 2024
Chief

Chief MF26000B Instrukcja

23 Września 2024
Chief

Chief FSB018BLK Instrukcja

23 Września 2024
Chief

Chief TPK1 Instrukcja

22 Września 2024
Chief

Chief PDR2612B Instrukcja

22 Września 2024
Chief

Chief CMA395 Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

Rocstor

Rocstor Y10N027-B1 Instrukcja

11 Grudnia 2024
StarTech.com

StarTech.com ARMQUADSS Instrukcja

10 Grudnia 2024
CTA Digital

CTA Digital ADD-AVPMB Instrukcja

10 Grudnia 2024
Gabor

Gabor FPC-85 Instrukcja

10 Grudnia 2024
Gabor

Gabor FPS-L Instrukcja

10 Grudnia 2024
Gabor

Gabor TM-UL Instrukcja

10 Grudnia 2024
Kanto

Kanto FMX2 Instrukcja

9 Grudnia 2024
Gabor

Gabor FSM-L Instrukcja

9 Grudnia 2024
Dell

Dell MDS19 Instrukcja

8 Grudnia 2024
Proaim

Proaim CT-SDCF-PRO Instrukcja

7 Grudnia 2024