Instrukcja obsługi Chief LSM5536

Chief Wsparcie dla płaskich paneli LSM5536

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief LSM5536 (24 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/24

I N S T A L L A T I O N I N S T R U C T I O N S

И Н С Т Р У К Ц И И П О У С Т А Н О В К Е

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

LSM LTM

FUSION LARGE HEIGHT ADJUST

FLAT PANEL MOUNTS

LSM/LTM Series

LSM/LTM Series Installation Instructions

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component. The wall to which the mount is being attached

may have a maximum drywall thickness of 5/8" (1.6cm).

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located on the LSM/LTM does not exceed

200 lbs (90.7 kg).

Installation Instructions LSM/LTM Series

DIMENSIONS

LTM

DIMENSIONS: [MILLIMETERS]

INCHES

34.57 878.1

1.75 44.5 15.10 383.4

2.92 74.11.00 25.4

.33 8.3

MINIMUM SPACING 12"

RAILS CAN BE SLID LEFT

OR RIGHT FOR OFFSET

20.54 521.7 7.00 177.8

16.52 419.6

5.29 134.5

12°

21.00 533.4

.32 8.1

.49 12.5

.98 25

1.48 37.5

1.97 50

2.46 62.5

2.95 75

3.44 87.5

3.94 100

4.43 112.5

4.92

5.91

NOTES:

MAXIMUM MOUNTING PATTERN IS 30.6"[777.2mm] WITHOUT

REVERSING UPRIGHTS.

MAXIMUM MOUNTING PATTERN IS 35.2"[894mm] WITH REVERSING

UPRIGHTS.

FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK

3. ENGAGEMENT IS .42"[10.7mm].

MOUNT IS 1.99"[50.5mm] DEEP WHEN FLAT TO WALL.

LSM

DIMENSIONS: [MILLIMETERS]

INCHES

1.00 25.4

.33 8.3

1.75 44.5

2.92 74.1

34.57 878.1

15.10 383.4

1.52 38.5

RAILS CAN BE SLID LEFT

OR RIGHT FOR OFFSET

MINIMUM WALL BRACKET

SPACING 12"

1.96 49.8

16.52 419.6

21.28 540.4 7.00 177.8

21.00 533.4

.53 13.5

.32 8.1

.49 12.5

.98 25

1.48 37.5

1.97 50

2.46 62.5

2.95 75

3.44 87.5

3.94 100

4.43 112.5

4.92 125

5.41 137.5

5.91 150

6.40 162.5

6.89 175

7.38 187.5

7.87

NOTES:

MAX MOUNTING PATTERN IS 31.8" (807.7 mm) WIDE REVERSING UPRIGHTS1. MAX MOUNTING PATTERN IS 34.3" (871.2 mm) WIDE REVERSING THE UPRIGHTS2. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK ENGAGEMENT IS .56"[14.2].3. MOUNT IS 1.96"[49.8mm] DEEP.

UPRIGHTS