Instrukcja obsługi Chief KRA202B
Chief
Flat panel steun
KRA202B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief KRA202B (4 stron) w kategorii Flat panel steun. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
dual mount
single display mount
Grommet Mounting Kit
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KRA202
KRA202 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! The KRA202 can ONLY be mounted
onto desks measuring between 3/4" and 3 1/2" in depth!
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
DESKTOP THICKNESS
RANGE .75- 3.50" [19.1 - 88.9]
DESK BASE SHOWN
FOR CLARITY
(NOT INCLUDED)
DESK SURFACE
Installation Instructions KRA202
3
TOOLS / PARTS FOR INSTALLATION
ASSEMBLY AND INSTALLATION
1. Remove desk clamp from mount by loosening button head
cap screw until clamp is completely disengaged from the
bolt. (See Figure 1)
NOTE: Button head cap screw can be removed or left loosely
in its hole after clamp is removed.
2. Manuever clamp so that it is totally removed from desk
mount. (See Figure 1)
Figure 1
3. Locate a flat surface (thickness of 3/4" minimum to 3 1/2"
maximum) on which to mount the column plate.
4. If mounting hole does not already exist on desk, drill
mounting hole in desk at desired mounting location.
IMPORTANT ! : Mounting hole must be a minimum of
5/16" in diameter and a maximum of 2"!
5. Thread 5/16-18" hex flange nut (C) onto 5/16-18 x 5" hex
head bolt (B). (See Figure 2)
6. Position mount on desk so that threaded hole is centered
over grommet hole. (See Figure 2)
7. Insert 5/16-18 x 5" bolt (B) through grommet bracket (A),
grommet hole and thread into center hole on underside of
mount as far as possible. (See Figure 2) and (See Figure 3)
Figure 2
8. Tighten hex flange nut (C) until grommet bracket (B) is
tightened against underside of desk. (See Figure 3)
Figure 3
9. Complete the installation following the mount installation
instructions.
1/2"
(if hole needs to be created)
3/16"
(included with mount)
A (1)
[grommet
bracket]
B (1)
5/16-18 x 5"
C (1)
5/16-18"
2
1
single display mount
dual mount
5
7
7
5
(B) (C)
(A)
(mounting arms not shown for clarity)
(mounting arms and desk not shown for clarity)
dual mount
single display mount
7
(C)
center hole
7
grommet hole
Specyfikacje produktu
| Marka: | Chief |
| Kategoria: | Flat panel steun |
| Model: | KRA202B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chief KRA202B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Flat panel steun Chief
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
21 Września 2024
Instrukcje Flat panel steun
- Flat panel steun Iiyama
- Flat panel steun HP
- Flat panel steun Icy Box
- Flat panel steun Pyle
- Flat panel steun NEC
- Flat panel steun Vogel's
- Flat panel steun 3M
- Flat panel steun Hitachi
- Flat panel steun Newstar
- Flat panel steun Reflecta
- Flat panel steun Techly
- Flat panel steun Da-Lite
- Flat panel steun Luxor
- Flat panel steun Steren
- Flat panel steun Barkan
- Flat panel steun Atlantic
- Flat panel steun Konig
- Flat panel steun HQ
- Flat panel steun BakkerElkhuizen
- Flat panel steun Peerless
- Flat panel steun SMS Smart Media Solutions
- Flat panel steun Monoprice
- Flat panel steun Atdec
- Flat panel steun Premier Mounts
- Flat panel steun Cabstone
- Flat panel steun SmartMetals
Najnowsze instrukcje dla Flat panel steun
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
20 Września 2024
20 Września 2024