Instrukcja obsługi Chief FPM4101


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief FPM4101 (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
8803-000034 Rev. B 05/05
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
INSTALLATION INSTRUCTIONS
FPM SERIES
SMALL FLAT PANEL DISPLAY
PITCH-ADJUSTABLE WALL MOUNT
Exclusive Q2™ Mounting System
Prior to assembly, unpack carton completely and verify contents.
If you are missing any of the following components, Service at 1-800/582-6480 please contact Customer
(1) FPM Wall Bracket (4) Drywall Anchor
(2) Wood Screw (2) Washer, Flat, .25 ID X .56 OD
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
Flat Panel Displays are Extremely Fragile.
If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),
DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.
Interface Bracket Installation:
1. See installation procedures accompanying your mounting bracket.
Optional Latching Flag Placement:
1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).
2. Reposition latching flag and secure using Phillips head screw, Nylock nut.
CAUTION!
Figure 1
Remove screw
and nut
Move latch
Figure 2
Drywall Installation Procedures:
Minimum Sheetrock Thickness ½ Inch.
2. Using the wall bracket as a template at the desired mounting location, mark the location of the four
outer mounting holes.
3. Using a 3/8-inch drill, drill four pilot holes
to a minimum depth of 1 1/2
at the locations marked
in Step 2.
4. Install an anchor bolt in one of the pilot holes and tighten anchor bolt until it is fully seated (see
Figure 3).
5. Remove and retain bolt and washer from anchor and repeat Step 4 and 5 for three remaining anchor
bolts.
6. Using four bolts, with washers installed, secure wall bracket to wall.
Wood Stud Installation Procedures:
1. Locate stud and, using wall bracket as a template at the desired height, mark the location of the two
center mounting holes.
2. Install a .25 ID x .06 OD flat washer on each of the two wood screws.
3. Using the two wood screws with flat washers installed, secure wall bracket to wall.
Mounting Display with Interface Bracket to Wall Bracket:
1. Make sure the latching flag on the mounting bracket is in the unlocked position (see Figure 4).
2. Place your small flat panel display; with interface bracket attached, onto the wall bracket, making
sure it is securely seated.
3. Lower the latching flag on the wall bracket, locking small flat panel display in place (see Figure 5).
Figure 5
CAUTION!
Outer Mountin
g
Holes
Figure 4
Locke
d
Unlocke
d
%%c0.375
(
PREDRILL HO LE
)
INSERT ANCHOR INTOPPREDRILLED HOLE
CW
A
NCHOR BARBP
(
STOPS ANCHOR ROTATIO N
)
#10-24 Screw Ancho
r
O
0.375
(
Predrill Hole
)
Insert anchor into
predrilled hole Anchor Barb
(Stops anchor rotation)
Turn 10-24 screw clockwise
until anchor fully seats
against back side of wall
CW
Figure 3
Inner Mountin
Holes


Specyfikacje produktu

Marka: Chief
Kategoria: Wsparcie dla płaskich paneli
Model: FPM4101

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief FPM4101, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Wsparcie dla płaskich paneli Chief

Chief

Chief RSA213 Instrukcja

28 Grudnia 2024
Chief

Chief RPA640 Instrukcja

28 Grudnia 2024
Chief

Chief RPMA204 Instrukcja

28 Grudnia 2024
Chief

Chief K1D120BXDL Instrukcja

28 Grudnia 2024
Chief

Chief TS218SU Instrukcja

9 Grudnia 2024
Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief MFQUB Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024
Chief

Chief K4G210B Instrukcja

23 Września 2024
Chief

Chief MF26000B Instrukcja

23 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli