Instrukcja obsługi Chief AS3LDP7

Chief Wsparcie dla płaskich paneli AS3LDP7

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief AS3LDP7 (4 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

I N S T A L L A T I O N I N S T R U C T I O N S

Patent Pending

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

Tempo™ Flat Panel Wall Mount System, PDU Bundle

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

AS3LDP7

AS3LDP7 Installation Instructions

DISCLAIMER

Legrand AV and its affiliated corporations and subsidiaries

(collectively “Legrand AV”), intend to make this manual |

accurate and complete. However, Legrand AV makes no claim |

that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Legrand AV

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Legrand AV

assumes no responsibility for accuracy, completeness or

sufficiency of the information contained in this document.

Chief® is a registered trademark of Legrand AV Inc.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: TO REDUCE THE RISK OF

BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS:

• Always turn off power at source before putting on or

taking off parts.

• Use this mounting system only for its intended use as

described in these instructions. Do NOT use

attachments not recommended by the manufacturer.

• Never operate this mounting system if it has a

damaged test cord or test plug. If it is not working

properly during testing, return the mounting system to

a service center for examination and repair.

• Keep the test power cord away from heated surfaces.

• Never operate the mounting system with the air

openings blocked. Keep the air openings free of lint,

hair, and the like.

• Never drop or insert any object into any opening.

• Do not use outdoors unless marked for outdoor use.

• Route cords and cables as shown in the installation

instructions.

• To disconnect, turn all controls to the off position, then

turn off power at source.

WARNING: RISK OF ELECTRIC SHOCK!

Connect this mounting system to a properly grounded outlet

only. See Grounding Instructions.

WARNING: Do not use this product outdoors.

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

DIMENSIONS: [MILLIMETERS]

INCHES

38.22 [970.7] M AX

7.84 [200] MIN

DISPLAY PATTERN

WIDTH

17.72

450.0

MAX D ISPLAY

PATTERN HEIG HT

.81

20.6

Installation Instructions AS3LDP7

TOOLS / PARTS FOR INSTALLATION

A (1)

[15 amp

power strip]

#10-32 x 3/8"

B (2)

[Power strip

Bracket]

C (2)

Hardware Bag

D (2)

[Nut - not used]

E (2)

[Wood screw - not used]

ASSEMBLY AND INSTALLATION

1. Install AS3LD wall mount to wall following AS3LD

installation instructions.

2. Use two #10-32 x 3/8" Phillips undercut screws (B) to secure

two power strip brackets (B) to side of AS3LD mount. (See

Figure 1)

Figure 1

3. Install power strip (A) into brackets installed in Step 2.

Power strip should "click" into place securely. (See Figure 2)

NOTE: Make sure power strip is installed with enough

clearance for end circuit breaker use.

Figure 2

4. Use a flathead screwdriver to gently pry power strip (A) from

brackets (B) to remove as needed. (See Figure 3)

Figure 3

(B) x 2

(A)

circuit breaker

Specyfikacje produktu

Marka:	Chief
Kategoria:	Wsparcie dla płaskich paneli
Model:	AS3LDP7

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief AS3LDP7, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wsparcie dla płaskich paneli Chief

Chief PWCU Instrukcja

16 Stycznia 2025

Chief MIWRFUB Instrukcja

16 Stycznia 2025

Chief TILD1X5NE1-M Instrukcja

16 Stycznia 2025

Chief MWRIWUB Instrukcja

16 Stycznia 2025

Chief TILD1X4NE1-R Instrukcja

16 Stycznia 2025

Chief TILD1X3NE1-L Instrukcja

16 Stycznia 2025

Chief TILD1X3NE1-R Instrukcja

16 Stycznia 2025

Chief KPP110B Instrukcja

16 Stycznia 2025

Chief TILD1X4NE1-L Instrukcja

16 Stycznia 2025

Chief TILD1X3NE1-M Instrukcja

16 Stycznia 2025

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

DQ 20-1070 Instrukcja

29 Stycznia 2025

Adicam MAX+ Film Cart Instrukcja

29 Stycznia 2025

Adicam STANDARD Film Cart Instrukcja

29 Stycznia 2025

Adicam MINI Film Cart Instrukcja

29 Stycznia 2025

DQ LCD-CM222 Instrukcja

28 Stycznia 2025

DQ 20-1069 Instrukcja

28 Stycznia 2025

StarTech.com ARMTRIO Instrukcja

16 Stycznia 2025

StarTech.com ARMBARDUOG Instrukcja

16 Stycznia 2025

StarTech.com ARMBARDUO Instrukcja

16 Stycznia 2025

StarTech.com H2MPV-MONITOR-MOUNT Instrukcja

16 Stycznia 2025