Instrukcja obsługi Chamberlain 041A5021-H-315

Chamberlain Niesklasyfikowane 041A5021-H-315

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chamberlain 041A5021-H-315 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

To prevent possible SERIOUS INJURY or DEATH from electrocution,

disconnect power to opener BEFORE proceeding.

To prevent damage to the receiver/logic board, do not touch the printed

circuit board of the replacement receiver/logic board during installation.

REPLACING RECEIVER/LOGIC

PANEL ASSEMBLY

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

This assembly is a replacement for your original receiver/logic

panel assembly. See side two for code programming instructions.

Depending on model type, you may have to remove the light lens

before proceeding with replacement part installation. The receiver/

logic panel assembly is located as shown below with corresponding

garage door opener models. The light lens is removed.

1. Disconnect all wires from the terminal screws of your opener’s

receiver/logic panel assembly, noting color of wires.

2. Remove screws to disengage the assembly from the opener

chassis.

3. Disconnect assembly from opener by holding the wire connector

plug and pulling down on the panel.

4. Install replacement assembly by reversing previous steps.

Connector plug is polarized. Take care to seat it properly and do

not force connection.

5. Re-connect power.

NOTE: A test of the safety reverse system is necessary for safe

operation. Instructions are on page two and in your opener’s manual.

Open and close force settings may also require adjustment. Refer to

your owner’s manual.

CAUTION

Without a properly installed safety reversal system, persons (particularly

small children) could be SERIOUSLY INJURED or KILLED by a closing

garage door.

• Safety reversal system MUST be tested every month.

• If one control (force or travel limits) is adjusted, the other control may

also need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be

tested. Door MUST reverse on contact with 1-1/2” (3.8 cm) high

object (or 2x4 laid flat) on the floor.

Select a remote control push button to operate the opener.

1. Press and hold the selected remote control push button

2. Then press and release the “SMART” (Learn) button on the opener

panel. The opener light will flash once.

3. Release the remote control push button.

Now the opener will operate when the remote push button is pressed.

NOTE: If you release the remote control push button before the

opener light flashes, the receiver will not learn the code.

Garage Door Opener

(With “Smart” Button)

“Smart” (learn)

Button

Indicator Light

Kg Kg

1 2 3

Select a

push button

• Press and hold the “SMART” button on the opener panel until the

indicator light turns off (about 6 seconds). ALL the codes the

opener has learned will be erased.

• To reprogram, repeat Steps 1–3 for each remote control in use.

Code programming instructions are also located on the opener

panel.

Conduct the Safety Reverse Test After:

• Each adjustment of door arm length, force controls or limit

controls.

• Any repair to or adjustment of the garage door (including springs

and hardware).

• Any repair to or buckling of the garage floor.

• Any repair or adjustment to the opener.

• Place a one-inch board (or a 2x4 laid flat) on the floor, centered

under the garage door.

• Operate the door in the down direction. The door must reverse on

striking the obstruction.

If the door stops on the obstruction, it is not traveling far enough in

the down direction.

• Increase the DOWN limit by turning the DOWN limit adjustment

screw counterclockwise 1/4 turn.

• Repeat the test.

NOTE: On a sectional door, make sure limit adjustments do not force

the door arm beyond a straight up and down position.

• When the door reverses on the one-inch board, remove the

obstruction and run the opener through 3 or 4 complete travel

cycles to test adjustment.

NOTE: If the door will not reverse after repeated adjustment attempts,

call for professional garage door service.

WAR

ARN

NING

ING

Specyfikacje produktu

Marka:	Chamberlain
Kategoria:	Niesklasyfikowane
Model:	041A5021-H-315

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chamberlain 041A5021-H-315, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Chamberlain

Chamberlain 041-0181-000 Instrukcja

8 Października 2024

Chamberlain PILCEV-P1 Instrukcja

7 Października 2024

Chamberlain RTX8P Instrukcja

2 Października 2024

Chamberlain MYQ-G0201 Instrukcja

2 Października 2024

Chamberlain 041D9204 Instrukcja

1 Października 2024

Chamberlain 801C-P Instrukcja

27 Września 2024

Chamberlain myQ-SGC2WCH Instrukcja

20 Września 2024

Chamberlain 7702C-P Instrukcja

19 Września 2024

Chamberlain myQ Smart Garage Video Keypad Instrukcja

17 Września 2024

Chamberlain 940EV-P2 Instrukcja

12 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024