Instrukcja obsługi Casio G-Shock GLX-5600VH-1ER

Casio Oglądać G-Shock GLX-5600VH-1ER

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Casio G-Shock GLX-5600VH-1ER (5 stron) w kategorii Oglądać. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

Operation Guide 3151

MO0803-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Warning!

•The measurement functions built into this watch are not intended for use in taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonably accurate representations only.

•The longitude, lunitidal interval, Moon phase indicator and tide graph data that

appear on the display of this watch are not intended for navigation purposes.

Always use proper instruments and resources to obtain data for navigation

purposes.

•This watch is not an instrument for calculating low tide and high tide times. The

tide graph of this watch is intended to provide a reasonable approximation of tidal

movements only.

•CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any

claims by third parties that may arise through the use of this watch.

About This Manual

•Button operations are indicated using the letters shown

in the illustration.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Fur ther details and technical information can be

found in the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the display.

Stopwatch Mode

World Time ModeTide/Moon Data Mode

Countdown Timer ModeAlarm Mode

Press C.

Timekeeping Mode

▲

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

•The tide graph shows tidal movements for the current

date in accordance with the current time as kept in the

Timekeeping Mode.

•The Moon phase indicator shows the current Moon

phase in accordance with the current date as kept in the

Timekeeping Mode.

Important!

•Be sure to configure the current time and date, and your

Home Site data (data for the site where you use the

watch) correctly before using the functions of this watch.

See “Home Site Data” for more information.

Day of week

Month – Day

Tide graph

Moon phase indicator

Hour : Minutes Seconds

PM indicator

Setting the Time and Date

This watch is preset with UTC differential values that represent each time zone

around the globe. Before setting the time, be sure to set the UTC differential for your

Home Site first, which is the location where you normally will be using the watch.

•Note that World Time Mode times are all displayed based on the time and date

settings you configure in the Timekeeping Mode.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

•Be sure to configure the correct UTC differential for

your Home Site before configuring any other

Timekeeping Mode settings.

•See the “UTC Differential/City Code List” for information

about the UTC differential settings that are supported.

Seconds

2. Press C to move the flashing in the sequence shown below to select other

settings.

Hour

UTC

Differential Minutes

Year

DST

Day Month

Seconds

Flash Alert

3. When the setting you want to change is flashing, use D B and to change it as

described below.

Reset the seconds to 00

Toggle between Daylight Saving

Time (ON) and Standard Time

(OFF)

Press D.

To do this: Do this:Screen

•See “Daylight Saving Time (DST) Setting” below for details about the DST setting.

• The UTC differential setting range is –12.0 to +14.0, in 0.5-hour units.

•When DST is turned on, the UTC differential setting range is –11.0 to +15.0, in

0.5-hour units.

• For information about Flash Alert, see “Flash Alert”.

4. Press A twice to exit the setting screen.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Specify the UTC differential

Change the hour or minutes

Change the year, month or day

Use D (+) and B (–).

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and 24-

hour timekeeping.

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST) Setting

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To toggle the Timekeeping Mode time between DST and Standard Time

1.In the Timekeeping Mode, hold down until theA

seconds start to flash, which indicates the setting

screen.

2. Press C once and the DST setting screen appears.

3. Press to toggle between Daylight Saving Time (DON

displayed) and Standard Time ( displayed).OFF

4. Press twice to exit the setting screen.A

•The DST indicator appears on the Timekeeping, and

Tide/Moon Data screens to indicate that Daylight Saving

Time is turned on. In the case of the Tide/Moon Data

Mode, the DST indicator appears on the Tide Data

screen only.

Home Site Data

Moon phase, tide graph data, and Tide/Moon Data Mode data will not be displayed

properly unless Home Site data (UTC differential, longitude and lunitidal interval) is

configured correctly.

DST indicator

On/Off status

•The UTC differential indicates the time differential with Greenwich, England.

•The letters UTC is the abbreviation for Coordinated Universal Time, which is the

world-wide scientific standard of timekeeping. It is based upon carefully maintained

atomic (cesium) clocks that keep time accurately to within microseconds. Leap

seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s

rotation.

•The lunitidal interval is the time elapsing between the Moon’s transit over a meridian

and the next high tide at that meridian. See “Lunitidal Interval” for more information.

•This watch displays lunitidal intervals in terms of hours and minutes.

•The “Site/Lunitidal Interval Data List” provides UTC differential and longitude

information around the world.

•The following is the initial factory default Home Site data (Tokyo, Japan) when you

first purchase the watch and whenever you have the battery replaced. Change these

settings to match the area where you normally use the watch.

UTC differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,

20 minutes)

To configure Home Site data

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press twice to display the UTC differential settingC

screen, and confirm that the setting is correct.

•If the UTC differential setting is not correct, use D (+)

and B (–) to change it.

3. Press to display the longitude value setting screen.A

4. Press C to move the flashing in the sequence shown

below to select other settings.

Lunitidal Interval

Hours

Lunitidal Interval

Minutes

Longitude

(East/West)

Longitude

Value

Longitude value

Longitude (East/West)

Operation Guide 3151

5. While the setting you want to change is flashing, use D B and to change it as

described below.

Setting

Longitude Value

Longitude

(East/West)

Lunitidal Interval

Hours, Minutes

Button Operations

Use D (+) and B (–) to change the setting.

•You can specify a value from 0 to 180° °, in 1-

degree units.

Use D to switch between east longitude ( )

and west longitude ( ).

Use D (+) and B (–) to change the setting.

6. Press A to exit the setting screen.

Screen

Tide/Moon Data

Tide/Moon data lets you view the Moon age and the Moon

phase for a particular date, and tidal movements for a

particular date and time for your Home Site.

•When you enter the Tide/Moon Data Mode, the data for

6:00 a.m. on the current date appears first.

•If you suspect that the Tide/Moon data is not correct for

some reason, check the Timekeeping Mode data

(current time, date, and Home Site settings), and make

changes as required.

•See “Moon Phase Indicator” for information about the

Moon phase indicator and “Tide Graph” for information

about the tide graph.

•All of the operations in this section are performed in the

Tide/Moon Data Mode, which you enter by pressing C.

Month – Day

Tide graph

Moon phase indicator

Time

Tide/Moon Data Screens

In the Tide/Moon Data Mode, press to toggle between the Tide Data screen andA

the Moon Data screen.

Press .A

Moon Data ScreenTide Data Screen

▲

Moon phase indicator

Time Moon age

Tide graph

Month – Day

•While the Tide Data screen is displayed, press to advance to the next hour.D

•While the Moon Data screen is displayed, press to advance to the next day.D

•You also can specify a particular date (year, month, day) to view its tide data and

Moon data. See “To specify a date” for more information.

•When you enter the Tide/Moon Data Mode, the screen (tide data or Moon data) that

was displayed the last time you exited the mode appears first.

To specify a date

1. In the Tide/Moon Data Mode, hold down A until the

year setting starts to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select the other settings.

Month DayYear

Month – DayYear

3. While a setting is flashing, use (+) or (–) to change it.D B

•You can specify a date in the range of January 1, 2000 to December 31, 2099.

4. Press A to exit the setting screen.

5. Use to display either the Tide Data screen or the Moon Data screen.A

World Time

World Time shows the current time in 48 cities (29 time

zones) around the world.

•The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check the UTC differential of

your Home Site Data (Home City) and the current

setting of the Timekeeping Mode time.

•Select a city code in the World Time Mode to display the

current time in any particular time zone around the

globe. See the “UTC Differential/City Code List” for

information about the UTC differential settings that are

supported.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

City code

Current time in

selected city

To view the time in another city

While in the World Time Mode, press D to scroll eastwardly through the city codes

(time zones).

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle between Daylight Saving Time

(DST indicator displayed) and Standard Time (DST

indicator not displayed).

•The DST indicator is shown on the World Time Mode

screen while Daylight Saving Time is turned on.

•Note that changing the Daylight Saving Time for any city

code causes the setting to be applied to all city codes.

DST indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes. It also includes Auto-Start.

•The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

1/100 second

Hours

Minutes

Seconds

To measure times with the stopwatch

Start Stop

Elapsed Time

➤

Re-start Clear

D➤

Stop

D➤D➤A

Split Time

Start Split

➤

Split release Clear

A➤

Stop

A➤D➤A

Two Finishes

Split

➤

Stop Clear

A➤

Split release

D➤A➤A

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

(SPL displayed)

Start

About Auto-Start

With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation

starts automatically when the countdown reaches zero.

During the final three seconds of the countdown, a beeper sounds with each second.

To use Auto-Start

1. While the stopwatch screen is showing all zeros in the

Stopwatch Mode, press A.

•This displays a 5-second countdown screen.

•To return to the all zeros screen, press A again.

2. Press D to start the countdown.

•When the countdown reaches zero, a tone sounds and a

stopwatch timing operation starts automatically.

•Pressing D while the Auto-Start countdown is in

progress will start the stopwatch immediately.

Countdown Timer

You can set the countdown timer within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero. The countdown timer also has an

auto

repeat feature and a progress beeper that signals

the progress of the countdown.

•All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing C.

Configuring the Countdown Timer

The following are the settings you should configure before

actually using the countdown timer.

Countdown start time; Auto-repeat on/off; Progress

beeper on/off

•See “To configure the countdown timer” for information

about setting up the timer.

Hours

Minutes

Seconds

Auto-repeat

When auto-repeat is turned on, the countdown restarts automatically from the

countdown start time when it reaches zero. If left running, the countdown is repeated a

total of eight times, after which it stops automatically.

When auto-repeat is turned off, the countdown stops when it reaches zero and the

display shows the original countdown start time.

•Pressing D while an auto-repeat countdown is in progress pauses the current

countdown. You can resume the auto-repeat countdown by pressing , or you canD

press A to reset to the countdown time starting value.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed

about the countdown status without looking at the display. The following describes the

types of beeper operations the watch performs during a countdown.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

•When the progress beeper is turned off, the countdown end beeper sounds for

about 10 seconds, or until you press any button to stop it.

•When the progress beeper is turned on, the countdown end beeper sounds for

about one second.

Progress Beeper

When the progress beeper is turned on, the watch uses beeps to signal countdown

progress as described below.

•Starting from five minutes before the end of the countdown, the watch emits four

short beeps at the top of each countdown minute.

•30 seconds before the end of the countdown, the watch emits four short beeps.

•The watch emits a short beep for each of the last 10 seconds of the countdown.

•If the countdown start time is six minutes or greater, the watch emits a short beep for

each second of the final 10 seconds before the five-minute point is reached. Four

short beeps are emitted to signal when the five-minute point is reached.

Operation Guide 3151

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Progress Beeper Auto-repeat

Hours Minutes

Button Operation

Use D (+) and B (–) to change the setting.

Press D to toggle auto-repeat on (

displayed) and off ( displayed).

Press D to toggle the progress beeper on ( )

and off ( ).

Setting

Hours, Minutes

Auto-repeat

Progress Beeper

•To specify a countdown start time of 24 hours, set .

4. Press A to exit the setting screen.

•You also can perform steps 1 and 2 of the above procedure whenever you need to

view the current auto-repeat and progress beeper settings.

3. When the setting you want to change is flashing, use B D and to change it as

described below.

Screen

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

•The countdown timer operation continues even if you

exit the Countdown Timer Mode.

•Press D while a countdown operation is in progress to

pause it. Press again to resume the countdown.D

•To stop a countdown operation completely, first pause it

(by pressing ), and then press . This returns theD A

countdown time to its starting value.

Alarms

You can set up to three independent multi-function alarms

with hour, minutes, month, and day. When an alarm is

turned on, the alarm tone sounds when the alarm time is

reached. One of the alarms is a snooze alarm, while the

other two are one-time alarms.

You also can turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

•There are three alarm screens numbered AL1and

AL2 for the one-time alarm, a snooze alarm screen

indicated by SNZ. The Hourly Time Signal screen is

indicated by SIG.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm number

Alarm date

(Month – Day)

Alarm time

(Hour : Minutes)

Alarm Types

The alarm type is determined by the settings you make, as described below.

•Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

•Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

•1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at the time you set, only during the month you set.

•Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at the time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

•To set a one-time alarm, display an alar m screen . To set theAL1or AL2

snooze alarm, display the SNZ screen.

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

3. Press C to move the flashing in the sequence shown below to select other

settings.

Hour Minutes Month Day

4. While a setting is flashing, use D and B to change it as described below.

To do this:

Change the hour

and minutes

Change the month

and day

Do this:

Use D (+) and B (–).

•With the 12-hour format, set the time correctly as

a.m. or p.m. ( indicator).P

•To set an alarm that does not include a month and/

or day, set for each setting.

5. Press A to exit the setting screen.

Screen

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off.

•Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the

SNZ

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn an alarm on and off

1. In the Alarm Mode, use to select an alarm.D

2. Press to toggle it on and off.A

•Turning on a alarm (AL1 AL2 SNZ, , or ) displays the

alarm on indicator on its Alarm Mode screen.

•In all modes, the alarm on indicator is shown for any

alarm that is currently turned on.

•The alarm on indicator flashes while the alarm is

sounding.

•The snooze alarm indicator flashes while the snooze

alarm is sounding and during the 5-minute intervals

between alarms.

Alarm on indicator

Snooze alarm

indicator

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal (SIG).

2. Press to toggle it on and off.A

•The Hourly Time Signal on indicator is shown on the

display in all modes while this function is turned on.

Hourly time signal

on indicator

Illumination

This watch has an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch’s auto light switch turns on illumination

automatically when you angle the watch towards your

face.

•The auto light switch must be turned on (indicated by

the auto light switch indicator) for it to operate.

•See “Illumination Precautions” for other important

information about using illumination.

To illuminate the display manually

In any mode, press to turn on illumination.B

•The above operation turns on illumination regardless of

the current auto light switch setting.

Auto light switch

indicator

•You can use the procedure below to select either 1.5 seconds or 3 seconds as the

illumination duration. When you press , the illumination will remain on for aboutB

1.5 seconds or 3 seconds, depending on the current illumination duration setting.

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

While the seconds are flashing, press B to toggle the

setting between 1.5 seconds ( ) and 3 seconds ( ).

3. Press twice to exit the setting screen.A

About the Auto Light Switch

Turning on the auto light switch causes illumination to turn on, whenever you position

your wrist as described below in any mode.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes illumination to turn on.

• Wear the watch on the outside of your wrist.

Parallel to

ground More than

40°

Warning!

••••

•Always make sure you are in a safe place whenever you are reading the

display of the watch using the auto light switch. Be especially careful when

running or engaged in any other activity that can result in accident or injury.

Also take care that sudden illumination by the auto light switch does not

startle or distract others around you.

••

•When you are wearing the watch, make sure that its auto light switch is turned

off before riding a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create a

distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down B for about three seconds to toggle the auto

light switch on (auto light switch indicator displayed) and off (auto light switch indicator

not displayed).

•The auto light switch indicator remains in all modes while the auto light switch is

turned on.

•In order to protect against running down the battery, the auto light switch will turn off

automatically approximately six hours after you turn it on. Repeat the above

procedure to turn the auto light switch back on if you want.

Specyfikacje produktu

Marka:	Casio
Kategoria:	Oglądać
Model:	G-Shock GLX-5600VH-1ER

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Casio G-Shock GLX-5600VH-1ER, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Oglądać Casio

Casio G-Shock GMA-B800 Instrukcja

9 Października 2024

Casio GW-3000BD-1AER Instrukcja

9 Października 2024

Casio G-Shock GW-9500 Instrukcja

8 Października 2024

Casio Edifice ECB 950 Instrukcja

7 Października 2024

Casio G-Shock GBD-800 Instrukcja

7 Października 2024

Casio G-Shock GR-B100 Instrukcja

7 Października 2024

Casio Baby-G MSG-S500 Instrukcja

7 Października 2024

Casio Baby-G BGA-200-1E2ER Instrukcja

6 Października 2024

Casio Edifice EFA-112D-1AVEF Instrukcja

6 Października 2024

Casio G-Shock GST-B600 Instrukcja

5 Października 2024

Instrukcje Oglądać

Najnowsze instrukcje dla Oglądać

Rolex Submariner Instrukcja

9 Października 2024

Seiko 6N76 Instrukcja

8 Października 2024

Seiko 6N53 Instrukcja

8 Października 2024

Seiko 6N52 Instrukcja

8 Października 2024

Seiko 6G28 Instrukcja

8 Października 2024

Seiko 4N30 Instrukcja

8 Października 2024

Seiko 4227 Instrukcja

8 Października 2024

Seiko 6N32 Instrukcja

8 Października 2024

Seiko 6N42 Instrukcja

8 Października 2024

Seiko 6N22 Instrukcja

8 Października 2024