Instrukcja obsługi Casio AMWS850SG-2AV

Casio Oglądać AMWS850SG-2AV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Casio AMWS850SG-2AV (6 stron) w kategorii Oglądać. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

Operation Guide 5208

MO1106-EA

E-1

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much as

possible.

•When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

•You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is only partially covered.

Bright Light

Solar cell

E-2

Battery charges in the light. Battery discharges in the dark.

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

•The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions being disabled. If the battery goes dead, you will have to re-configure

watch settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

E-3

•The actual level at which some functions are disabled depends on the watch model.

•Be sure to read “Power Supply” (page E-33) for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

•See “Power Saving Function” (page E-46) for more information.

E-4

About This Manual

•Depending on the model of your watch, display text

appears either as dark figures on a light background, or

light figures on a dark background. All sample displays

in this manual are shown using dark figures on a light

background.

•Button operations are indicated using the letters shown

in the illustration.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Fur ther details and technical information can be

found in the “Reference” section.

E-5

Contents

General Guide ......................................................................................................... E-8

Timekeeping .......................................................................................................... E-10

World Time ............................................................................................................. E-17

Alarms .................................................................................................................... E-20

Countdown Timer .................................................................................................. E-24

Stopwatch .............................................................................................................. E-29

Illumination ............................................................................................................ E-31

Power Supply ........................................................................................................ E-33

Adjusting Home Positions ................................................................................... E-42

Reference .............................................................................................................. E-44

Specifications ....................................................................................................... E-50

E-6

Procedure Lookup

The following is a handy reference list of all the operational procedures contained in

this manual.

To set the current digital time and date .............................................................. E-11

To change the Daylight Saving Time (summer time) setting ............................ E-15

To view the time in another city ........................................................................... E-18

To toggle a city code time between Standard Time

and Daylight Saving Time ............................................................................... E-18

To swap your Home City and World Time City ................................................... E-19

To set an alarm time ............................................................................................. E-21

To turn an alarm on and off .................................................................................. E-23

To turn the Hourly Time Signal on and off .......................................................... E-23

E-7

To configure the countdown timer ...................................................................... E-25

To use the countdown timer ................................................................................ E-27

To measure times with the stopwatch ................................................................ E-30

To illuminate the display ...................................................................................... E-31

To specify the illumination duration ................................................................... E-32

To check the current battery level ....................................................................... E-35

To adjust home positions ..................................................................................... E-42

To turn the button operation tone on and off ..................................................... E-45

To recover from the sleep state ........................................................................... E-47

E-8

Timekeeping Mode

▲

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the face of the watch.

Battery Level Indicator

▲

E-9

Stopwatch Mode Countdown Timer Mode

Alarm Mode

▲

World Time Mode

▲

C C

▲

Operation Guide 5208

E-10

•All of the operations in this section are performed in the Timekeeping Mode, which

you can enter by pressing (page E-8).C

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

•When setting the time, you can also configure settings for the 12/24-hour format.

•Each press of D cycles the digital display in the sequence shown below.

Day

Day of week

▲

PM indicator

Hour : Minute

SecondSecond Second

Month

▲

E-11

City code

Setting the Digital Time and Date

Make sure you select your Home City code before you change the current time and

date settings. World Time Mode times are all displayed in accordance with the

Timekeeping Mode settings. Because of this, World Time Mode times will not be

correct if you do not select the proper Home City code before setting the time and

date in the Timekeeping Mode.

To set the current digital time and date

1. In the Timekeeping Mode, hold down A for about two

seconds, until “ADJ” appears on the display.

•Your current Home City code will be flashing on the

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

E-12

3. While the setting you want to change is flashing, use D and B to change it as

explained below.

Screen: To do this:

Change the city code

Toggle between Daylight Saving Time

(ON) and Standard Time (OFF).

Toggle between 12-hour ( ) and12H

24-hour ( ) timekeeping24H

Reset the seconds to 00

Do this:

Press D (east) and B (west).

Press D.

City Code

Language Illumination

Duration Day Month Ye a r

DST 12/24-Hour

Format Seconds Hour Minutes

Button Operation

To ne

E-13

To do this:

Change the hour or minutes

Change the year

Change the month or day

Toggle the button operation tone

between (on) and (off)

Toggle the illumination duration between

LT1 (approximately 1.5 seconds) and

LT3 (approximately 3 seconds).

Change the day of the week language

ENG: English : PortuguesePOR

ESP: Spanish : FrenchFRA

DEU: German ITA : Italian

Screen: Do this:

Use D (+) and B (–).

Press D.

Use D (+) and B (–).

•See “City Code Table” at the back of this manual for a complete list of available

city codes.

E-14

4. Press A to exit the setting screen.

•The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears for times in the

range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

E-15

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about two seconds, until “ADJ” appears

on the display.

•Your current Home City code will be flashing on the screen.

2. Press C once to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time ( displayed) and StandardON

Time (OFF displayed).

4. When the setting you want is selected, press A to exit the setting screen.

•The DST indicator appears on the display to indicate that Daylight Saving Time is

turned on.

E-16

Analog Timekeeping

The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

Note

•The hands for the analog timepiece move to adjust to a new setting whenever any of

the following occurs.

When you change the digital time setting

When you change the Home City code and/or DST setting

•If the analog time does not match the digital time for any reason, use the procedure

described under “To adjust home positions” (page E-42) to match the analog setting

to the digital setting.

•Whenever you need to adjust both the digital and the analog time settings, make

sure you adjust the digital setting first.

•Depending on how much the hands have to move in order to synchronize to the

digital time, it may take some time before they stop moving.

E-17

World Time

The World Time Mode digitally displays the current time in

48 cities (31 time zones) around the world.

•If the current time shown for a city is wrong, check your

Home City time settings and make the necessary

changes (page E-11).

•After you press C to enter the World Time Mode, your

currently selected World Time City code will appear on

the digital display for about two seconds. After that, the

current time in that city will appear.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C

(page E-9).

City code

Current time in

selected city

E-18

To view the time in another city

If you press D while in the World Time Mode, your currently selected World Time City

code will appear on the digital display for about two seconds. After that, the current

time in that city will appear. Pressing D again while the World Time City code is

displayed will scroll to the next city code.

•For full information on city codes, see the “City Code Table” at the back of this

manual.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle Daylight Saving Time (DST

indicator displayed) and Standard Time (DST indicator

not displayed).

• The DST indicator will appear on the display whenever

you display a city code for which Daylight Saving Time is

turned on.

DST indicator

E-19

• Note that the DST/Standard Time setting affects only the currently displayed city

code. Other city codes are not affected.

Swapping your Home City and World Time City

You can use the procedure below to swap your Home City and World Time City. This

changes your Home City to your World Time City, and your World Time City to your

Home City. This capability can come in handy when you frequently travel between two

cities in different time zones.

To swap your Home City and World Time City

1. In the World Time Mode, use D to select the World Time City you want.

2. Hold down A and B until the watch beeps.

• This will make the World Time City you selected in step 1 your Home City, and cause

the hour and minute hands to move to the current time in that city. At the same time,

it will change the Home City you had selected prior to step 2 your World Time City.

• After swapping the Home City and World Time City, the watch stays in the World

Time Mode with the city that was selected as the Home City prior to step 2 now

displayed as the World Time City.

Operation Guide 5208

E-20

Alarms

The Alarm Mode lets you configure five daily alarms. You

also can use it to turn the Hourly Time Signal on or off.

•The watch beeps for about 10 seconds when an alarm

time is reached.

•Turning on the Hourly Time Signal causes the watch to

beep on the hour every hour.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C (page

E-9).

Alarm time

(Hour : Minutes)

E-21

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm screens until the one whose

time you want to set is displayed.

AL1 AL2 AL3

SIG AL5 AL4

•The alarm screens are AL1, , , .AL2 AL3 AL4, and AL5

About 2 seconds

Alarm timeAlarm number

▲

E-22

2. After you select an alarm, hold down A for about two seconds until the hour setting

of the alarm time starts to flash. This is the setting mode.

•This operation turns on the alarm automatically.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D B (+) and (–) to change it.

5. Press A to exit the setting mode.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in.

•Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

E-23

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use to select the Hourly TimeD

Signal (SIG) (page E-21).

2. Press A to toggle it on and off.

Hourly time signal

on indicator

Alarm on indicator

E-24

Countdown Timer

Seconds

Minutes

Timer 1

Dual timers can be set with two different starting times. The watch can be configured

so the two timers alternate, so when one reaches the end of its countdown, the other

timer starts. You can specify a “number of repeats” value from 1 (once) to 10 (ten

times), which controls how many times the two-timer countdown operation is

performed. The starting time of each timer can be set in five-second steps up to 99

minutes, 55 seconds.

▲

2 seconds

Seconds

Minutes

Timer 2

E-25

The watch emits a short beep whenever either of the timers reaches the end of its

countdown during an ongoing timer operation. The watch emits a 5-second beep

when the end of the final timer operation (specified by the number of repeats) is

reached.

•All of the operations in this section are performed in the Countdown Timer Mode,

which you enter by pressing C (page E-9).

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero. The

beeper stops after about 5 seconds or when you press any button.

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-27) to display it.

E-26

•To disable either timer, set 00'00" as its countdown start time.

4. Press A to exit the setting screen.

Button Operation

Use D B (+) and (–) to change the setting.

Setting

Minutes, Seconds

Number of Repeats

Screen

2. Press C to move the flashing in the sequence shown below to select other

settings.

Timer 1

Minutes

Timer 1

Seconds

Timer 2

Seconds

Timer 2

Minutes

Number of Repeats

3. When the setting you want to change is flashing, use D B and to change it as

described below.

E-27

To use the countdown timer

Press while in the Countdown Timer Mode to start the countdown timer.D

•Pressing A while a countdown is in progress will display the repeat count (current

repeat count/preset number of repeats). The ongoing countdown will reappear

automatically after about two seconds.

•The countdown is performed by alternating between Timer 1 and Timer 2. A short

beep is emitted to signal a changeover from one timer to the other.

•

Pressing

while a countdown timer is stopped resets that time to the start time specified

by you.

•Press D to pause a countdown. Press again to resume.D

•The watch emits a 5-second beep when the end of the final timer operation

(specified by the number of repeats) is reached.

Current timer time

Preset number of repeats

Current repeat countTimer (1 or 2)

(Reset)

(Start/Stop)

▲

2 seconds

E-28

•Even if you exit the Countdown Timer Mode, the countdown timer operation

continues and the watch beeps as required.

•To stop a countdown operation completely, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

E-29

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 59 minutes, 59.99

seconds.

•The stopwatch continues to run until you stop it. If it

reaches its limit, it restarts from zero.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C

(page E-9).

Minutes

Seconds

Specyfikacje produktu

Marka:	Casio
Kategoria:	Oglądać
Model:	AMWS850SG-2AV
Materiał obudowy:	Metal
Wodoodporny:	Tak
Typ mechanizmu:	Kwarc (słoneczny)
Chronograf:	Nie
Stoper:	Tak
Typ zegarka:	Zegarek z bransoletką
Kolor obudowy:	Stal nierdzewna
Tworzywo paska:	Metal
Kolor główny paska:	Gold, Stainless steel
Kształt koperty:	Okrągły
Kolor tarczy zegarka:	Złoto/biały
Styl oznaczenia godzin i minut:	Bez oznaczenia
Konstrukcja produktu:	Sport
Podświetlenie LED:	Tak
Głębokość wodoszczelności:	50 m
Typ szkła:	Mineralny
Dedykowana płeć:	Męski
Liczba alarów:	5
Kolor oznaczenia godzin i minut:	Czarny
Liczba wskazówek:	2
Timer:	Tak
Chronometr:	Nie
Szkło odporne na zarysowania:	Tak
Strefy czasowe:	Tak
Data automatyczna:	Tak