Instrukcja obsługi Casio AMW720-1AV

Casio Oglądać AMW720-1AV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Casio AMW720-1AV (4 stron) w kategorii Oglądać. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Operation Guide 3796

Digital Time and Date

Use the Timekeeping Mode to set and view a digital display of the current time and date.

When setting the digital time, you can also configure settings for summer time

(Daylight Saving Time or DST).

To set the digital time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select the other settings.

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully and keep it on hand for later reference

when necessary.

Warning!

•The longitude, lunitidal interval, Moon phase indicator and tide graph data that

appear on the display of this watch are not intended for navigation purposes.

Always use proper instruments and resources to obtain data for navigation

purposes.

•This watch is not an instrument for calculating low tide and high tide times. The

tide graph of this watch is intended to provide a reasonable approximation of

tidal movements only.

•CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any

claims by third parties that may arise through the use of this watch.

About This Manual

•Button operations are indicated using the letters shown

in the illustration.

•For the sake of simplicity, the sample displays in this

manual do not show the analog hands of the watch.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the face of the watch.

Timekeeping

This watch features separate digital and analog

timekeeping. The procedures for setting the digital time

and analog time are different.

•The Moon phase indicator shows the current Moon

phase in accordance with the current date as kept in the

Timekeeping Mode.

•The tide graph shows tidal movements for the current

date in accordance with the current time as kept in the

Timekeeping Mode.

Important!

•Be sure to configure the current time and date, and your

Home Site data (data for the site where you use the

watch) correctly before using the functions of this watch.

See “Home Site Data” for more information.

4. Press A twice to exit the setting screen.

•The first press of A A displays the UTC differential setting screen. Pressing again

exits the setting screen.

•Resetting the seconds only (without changing the DST, hour, or minute setting)

causes the analog minute hand setting to be adjusted automatically.

•See “Digital Time Daylight Saving Time (DST) Setting” below for details about the

DST setting.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Digital Time Daylight Saving Time (DST) Setting

Daylight Saving Time (summer time) advances the digital time setting by one hour

from Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To toggle the Timekeeping Mode digital time between DST and Standard Time

1. In the Timekeeping Mode, hold down A until the seconds

start to flash, which indicates the setting screen.

2. Press C once to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time (ON

displayed) and Standard Time (OF displayed).

4. Press A twice to exit the setting screen.

•The DST indicator appears on the Timekeeping, Moon/

Tide Data, Alarm, and Hand Setting Mode screens to

indicate that Daylight Saving Time is turned on. In the

case of the Moon/Tide Data Mode, the DST indicator

appears on the tide data screen only.

Seconds DST Hour Minutes

Day Month Year

3. When the setting you want to change is flashing, use B and D to change it as

described below.

Home Site Data

Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed

properly unless Home Site data (UTC differential, longitude, and lunitidal interval) is

configured correctly.

•The UTC differential is a value that indicates the time difference between a

reference point in Greenwich, England and the time zone where a city is located.

•The letters “ ” “ ”UTC is the abbreviation for Universal Time Coordinated , which is the

world-wide scientific standard of timekeeping. It is based upon carefully maintained

atomic (cesium) clocks that keep time accurately to within microseconds. Leap

seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s

rotation.

•The lunitidal interval is the time elapsing between the Moon’s transit over a meridian

and the next high tide at that meridian. See Lunitidal Interval for more information.“ ”

•This watch displays lunitidal intervals in terms of hours and minutes.

•The Site/Lunitidal Interval Data List provides UTC differential and longitude“ ”

information around the world.

•The following is the initial factory default Home Site data (Tokyo, Japan) when you

first purchase the watch, and whenever you have the battery replaced. Change

these settings to match the area where you normally use the watch.

UTC differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,

20 minutes)

To configure Home Site data

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press A again to display the UTC differential setting

screen.

3. Press C to move the flashing in the sequence shown

below to select other settings.

UTC

Differential

Longitude

Value

East Longitude/

West Longitude

Lunitidal Interval

Hours

Lunitidal Interval

Minutes

MA0508-EA

Timekeeping

Mode

Moon/Tide Data

Mode

Stopwatch

Mode

Countdown Timer

Mode

Alarm

Mode

Dual Time

Mode

Hand Setting

Mode

Press .

Tide graph

Day of week

Month – Day

Moon phase indicator

Hour : Minutes

Seconds

PM indicator

Screen

DST

10:08

2006

To do this:

Reset the seconds to 00

Toggle between Daylight Saving Time (ON) and

Standard Time (

OF)

Change the hour or minutes

Change the year

Change the month or day

Do this:

Press .D

Use ).D (+) and B (–

DST indicator

On/Off status

UTC differential

Operation Guide 3796

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

•When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value after the alarm stops.

•When auto-repeat is turned on, the countdown will restart automatically without

pausing when it reaches zero. The alarm sounds in order to signal when the

countdown reaches zero.

•The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

•Press D while a countdown operation is in progress to pause it. Press D again to

resume the countdown.

•To completely stop a countdown operation, first pause it (by pressing ), and thenD

press A. This returns the countdown time to its starting value.

To set up the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

•If the countdown start time is not displayed, use the

procedure under To use the countdown timer“ ” to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Auto-repeatMinutesHours

3. While a setting is flashing, use D and B to change it as described below.

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing .C

•When the digital time DST setting is on, the UTC differential can be set in a range

of 11.0 to +15.0 in 0.5-hour units.–

5. Press A to exit the setting screen.

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press to toggle between 12-hour timekeeping andD

24-hour timekeeping.

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and the (AM) indicator appears to the leftA

of the hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

•The and A P indicators are not displayed with the Timekeeping Mode time on the

Countdown Timer Mode and Dual Time Mode screens.

Setting the Analog Time

Perform the procedure below when the time indicated by the analog hands does not

match the time of the digital display.

To adjust the analog time

1. In the Timekeeping Mode, press C six times to enter

the Hand Setting Mode.

2. Hold down A until the current digital time starts to

flash, which indicates the analog setting mode.

3. Press D to advance the analog time setting by

20 seconds.

•Holding down advances the analog time setting atD

high speed.

•If you need to advance the analog time setting a long way, hold down until theD

time starts advancing at high speed, and then press . This locks the high-B

speed hand movement, so you can release the two buttons. High-speed hand

movement continues until you press any button. It will also stop automatically

after the time advances 12 hours or if an alarm (multi-function alarm, Hourly Time

Signal, or countdown beeper) starts to sound.

4. Press A to exit the setting mode.

•The watch will automatically adjust the minute hand slightly to match its internal

second count when you exit the setting mode.

•To return to the Timekeeping Mode, press C.

4. When the setting you want to change is flashing, use D and B to change it as

described below.

Moon/Tide Data

Moon/tide data lets you view the Moon age and Moon

phase for a particular date, and tidal movements for a

particular date and time at your Home Site.

•If you suspect that the current Moon/tide data is wrong

for some reason, check the current Timekeeping Mode

settings (time, date, and Home Site), and correct them if

required.

•See “Moon Phase Indicator” for information about the

Moon phase indicator and Tide Graph“ ” for information

about the tide graph.

•All of the operations in this section are performed in the

Moon/Tide Data Mode, which you enter by pressing C.

3. While a setting is flashing, use D B (+) or (–) to change it.

•You can specify a date in the range of January 1, 2000 to December 31, 2099.

4. Press A to exit the setting screen.

5. Use A to display either the tide data screen or the Moon data screen.

Countdown Timer

You can set the countdown timer within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

•You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

•All of the operations is this section are performed in the

Countdown Timer Mode, which you can enter using C.

•To specify a countdown start time of 24 hours, set 0:00.

4. Press A to exit the setting screen.

•

The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen

while this function is turned on.

•Frequent use of auto-repeat and the alarm can run down battery power.

To view the current Moon/Tide Data Mode data

In the Moon/Tide Data Mode, press A to toggle between the tide data screen and the

Moon data screen.

•The tide graph shows the tide for the currently displayed time. The initial tide data

screen shows the level for 6:00 a.m. The Moon data screen shows the Moon age

and Moon phase for the current date.

Tide Data Screen Moon Data Screen

Press .

Tide

raph

Time

Moon a

e Year Month – Da

Year Month – Da

Moon phase indicator

•While the tide data screen is displayed, press D to advance to the next hour.

•While the Moon data screen is displayed, press D to advance to the next day.

•You can also specify a particular date (year, month, day) to view its tide data and

Moon data. See To specify a date for more information.“ ”

•When you enter the Moon/Tide Data Mode, the screen (tide data or Moon data) that

was displayed the last time you exited the mode appears first.

To specify a date

1. In the Moon/Tide Data Mode, hold down A until the

year setting starts to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select the other settings.

Year Month Day

To measure times with the stopwatch

Elapsed Time

Start Stop Re-start Stop Clear

Start Split

( displayed) SPL

Split release Stop Clear

Start Split Stop Split release Clear

Split Time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

ScreenSetting

UTC Differential

Longitude Value

East Longitude/

West Longitude

Lunitidal Interval

Hours, Minutes

Button Operations

Use D (+) and B (–) to change the setting.

•You can specify a value in the range of –12.0 to +14.0,

in 0.5-hour units.

Use D (+) and B (–) to change the setting.

• °You can specify a value in the range of 0 to 180 , in°

1-degree units.

Use D to switch between east longitude (

) and west

longitude ( ).

Use D (+) and B (–) to change the setting.

Tide Data Screen

Year Month Day –

Tide graph

Moon phase indicator

Time

Year

Month Day –

Seconds

Hours

Minutes

1/100 second

Timekeepin

Mode time

Seconds

Hours

Minutes

Screen

0:00

Do this:

Use ).D (+) and B (–

Press .D

To do this:

Change the hours or minutes

Toggle auto-repeat on (

ON ) and off (

OF)

Operation Guide 3796

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. While the seconds are flashing, press B to toggle the

illumination duration between 1.5 seconds (x) and 3

seconds ( ).

3. Press A twice to exit the setting screen.

Illumination

Two LEDs (light-emitting diodes) and a light guide panel

illuminate the face of the watch for easy reading in the

dark.

•See “Illumination Precautions” for more important

information.

To illuminate the face of the watch

In any mode (except when a setting screen is on the

display), press to illuminate the face of the watch.B

•You can use the procedure below to select either

1.5 seconds or 3 seconds as the illumination duration.

When you press , the illumination will remain on forB

about 1.5 seconds or 3 seconds, depending on the

current illumination duration setting.

Alarms

You can set up to three independent multi-function alarms

with hour, minutes, month, and day. When an alarm is

turned on, the alarm tone sounds when the alarm time is

reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other two are

one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

•There are three alarms numbered

1 through 3. You can

configure Alarm1 as a snooze alarm or a one-time

alarm. Alarms

2 and 3 can be used as one-time alarms

only.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

To select the operation of Alarm

1. In the Alarm Mode, use D to select Alarm1.

2. Press A to cycle through the available settings in the sequence shown below.

Alarm on

Alarm off

Snooze

alarm on

•The applicable alarm on indicator ( ) is displayed in all modes when anSNZ ALM

alarm is turned on.

•SNZ indicator flashes during the 5-minute intervals between alarms.

•Displaying the Alarm1 setting screen while the snooze alarm is turned on

automatically turns off the snooze alarm (making Alarm

1 a one-time alarm).

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone. You can

select Standard Time or Daylight Saving Time for the Dual Time Mode time.

•In the Dual Time Mode, the seconds count is synchronized with the seconds count

of the current digital time.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. In the Dual Time Mode, hold down A until the DST

setting starts to flash, which indicates the setting

screen.

3. Press C to move the flashing in the sequence shown

below to select the other setttings.

DST Hour Minutes

4. When the setting you want to change is flashing, use B and D to change it as

described below.

5. Press A to exit the setting screen.

•The DST indicator on the Dual Time Mode screen indicates that DST is turned on for

the Dual Time Mode time.

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Moon Phase Indicator

The Moon phase indicator of this watch indicates the current phase of the Moon as

shown below.

Moon Phase

Indicator

Moon Age 0.0 - 1.8

27.7 - 29.5

New

Moon First

Quarter

(Waxing)

Full

Moon Last

Quarter

(Waning)

1.9 - 5.5 5.6 - 9.2 9.3 - 12.9 13.0 - 16.6 16.7 - 20.2 20.3 - 23.9 24.0 - 27.6

Moon Phase

Moon phase (part you can see)(part you cannot see)

•The Moon phase indicator shows the Moon as viewed at noon from a position in the

Northern Hemisphere looking south. Note that at times the image shown by the

Moon phase indicator may differ from that of the actual Moon in your area.

•The left-right orientation of the Moon phase is reversed when viewing from the

Southern Hemisphere or from a point near the equator.

Moon Phases and Moon Age

The Moon goes through a regular 29.53-day cycle. During each cycle, the Moon

appears to wax and wane as the relative positioning of the Earth, Moon, and Sun

changes. The greater the angular distance between the Moon and the Sun,* the more

we see illuminated.

The angle to the Moon in relation to the direction at which the Sun is visible from the

Earth.

This watch performs a rough calculation of the current Moon age starting from day 0

of the moon age cycle. Since this watch performs calculations using integer values

only (no fractions), the margin for error of the displayed Moon age is ±1 day.

Alarm Types

The alarm type is determined by the settings you make, as described below.

••••

• Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

••

• Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

••

• 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at time you set, only during the month you set.

••

• Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at the time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

•To set a one-time alarm, display one of the screens

indicated by alarm number

2 or 3. To set the snooze

alarm, display the screen indicated by

2. After you select an alarm, hold down A until the hour

setting of the alarm time starts to flash, which indicates

the setting screen.

•This operation automatically turns on the alarm.

3. Press C to move the flashing in the sequence shown below to select other

settings.

Hour Minutes Month Day

4. While a setting is flashing, use D B (+) and (–) to change it.

•To set an alarm that does not include a month (daily alarm, monthly alarm),

set x for the month. Use D and B until the x

mark appears (between 12 and 1)

while month setting is flashing.

•To set an alarm that does not include a day (daily alarm, 1-month alarm),

set xx for the day. Use D and B until the

xx mark appears (between the end

of the month and 1) while the day setting is flashing.

•When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. ( indicator) or p.m. ( indicator).A P

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off or change it to a one-

time alarm.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the alarm

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn Alarms

22222

and

33333

, and the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select a one-time alarm

(alarm number

2 or 3

) or the Hourly Time Signal (:00).

2. Press A to toggle it on and off.

•Turning on a one-time alarm (

2 or 3) displays the alarm

on indicator on its screen.

•Turning on the Hourly Time Signal displays the hourly

time signal on indicator.

•The alarm on (ALM) indicator and Hourly time Signal on

(SIG) indicator are displayed in all modes.

Alarm time

(Hour : Minutes)

Alarm number

Alarm date (Month Day) –

Dual time

(Hour : Minutes)

Timekeepin

Mode time

DST indicator

Screen

DST

8:08

To do this:

Toggle between Daylight Saving Time (ON ) and

Standard Time (OF

)

Change the hour or minutes

Do this:

Press .D

Use ).D (+) and B (–

Alarm on indicator

Hourly time signal on

indicator

Specyfikacje produktu

Marka:	Casio
Kategoria:	Oglądać
Model:	AMW720-1AV
Wodoodporny:	Tak
Chronograf:	Tak
Stoper:	Tak
Kalendarz:	Tak
Typ zegarka:	Zegarek na rękę
Kolor obudowy:	Black, Orange, Silver
Kolor główny paska:	Czarny
Kształt koperty:	Okrągły
Kolor tarczy zegarka:	Czarny
Podświetlenie LED:	Tak
Głębokość wodoszczelności:	50 m
Dedykowana płeć:	Męski
Typ kalendarza:	Dzień