Instrukcja obsługi Café CTD90DP2NS1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Café CTD90DP2NS1 (24 stron) w kategorii Oven. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/24
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT — Save these
instructions for local inspector’s use.
• IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires a qualified installer or electrician.
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under Warranty.
• Product is for indoor use only.
Installation Instructions
27” & 30” Electric Built-In Wall Ovens
FOR YOUR SAFETY:
WARNING
Before beginning the installation, switch power off at the service panel and lock
the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight
on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to
200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
36” (91 cm) of String
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
T20 Screwdriver
Phillips Screwdriver
Wire Strippers
7/16” Nut Driver (combination ovens)
1/4” Nut Driver (30” combination ovens)
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
1 REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all
packing parts from oven, racks and heating elements. Remove protective film and labels on
the outer door and control panel. Also, remove plastic on trims and panel, all tape around the
oven and any shipping screws securing the oven to the base pad. Open oven door and remove
literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be
installed at the end of the installation process. The trim is wrapped separately and taped to the top
of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).
Consider recycling options for your appliance packaging material.
2 PREPARE THE OPENING
NOTE: If the cabinet does not have a solid
bottom, two braces or runners must be
installed to support the weight of the oven.
For single ovens, the runners and braces
must support 220 lbs (99 kg). For double and
combination ovens, the runners and braces
must support 400 lbs. (181 kg).
NOTE: If marks, blemishes or the cutout
opening are visible above the installed oven,
it may be necessary to add wood shims
under the runners until the marks or opening
are covered.
NOTE: If the cabinet does not have a front
frame and the sides are less than ¾” (1.9 cm)
thick, shim both sides equally to establish the
cutout width.
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven
may also be installed side by side, below a countertop, or below specified cooktops. See the label
on top of the oven for approved models.
DOUBLE AND COMBINATION OVEN INSTALLATIONS
A double or combination oven may be installed in a cabinet alone or above a warming drawer.
See the label on top of the oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for
specific requirements.
Suitable
Bracing
to Support
Runners
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
C
L
2 B CUTOUT FOR SINGLE OVENS – UNDER COUNTER
NOTE: These ovens are only approved to be installed under the specific models as labeled on
the unit.
NOTE: One cooktop may be centered over either
oven in the side-by-side installation.
Cutout – observe
all dimensions and
requirements.
2” (5.1 cm) Min.
30.5” (77.5 cm) 30” models
27” (68.58 cm) 27” models
Center Line Center Line
Side-by-Side Installations
Install two ovens in separate cutouts.
Cooktop
Cutout – observe
all dimensions and
requirements.
Continue to Section 4.
Dimension Dimension Description 27” Single Oven 30” Single Oven
ACabinet Width 25” (63.5 cm) min.
251»4” (64.1 cm) max.
281»2” (72.4 cm) min.
285»8” (72.7 cm) max.
BCutout Height 275»8” (70.2 cm) min.
281»8” (71.4 cm) max.
271»4” (69.2 cm) min.
275»16” (69.4 cm) max.
CClearance from cutout - top* 1” (2.5 cm) 1” (2.5 cm)
(11»4” (3.2 cm) for
PT9050
ZET1S and ZET1P)
DClearance from cutout - bottom* 1” (2.5 cm) 11»4” (3.2 cm)
EClearance from cutout - side edges* 1” (2.5 cm) 11»16” (1.75 cm)
FJunction Box Location 83»4” (22.2 cm) max.
right side only
91
»2” (24.1 cm) max.
right side only
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
IMPORTANT: Maintain
a minimum distance
of 31-1/4” from the
top surface of the
countertop to the
wall oven platform to
ensure that the cooktop
and wall oven do not
interfere with each other
(see picture).
31-1/4” min.
(79.4 cm)
SIDE VIEW
Cooktop
Wall Oven
2-1/2” min. (6.4cm)
2 A CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick,
shim both sides equally to establish the cutout width.
These ovens
are not
approved for
installations that
stack one single
wall oven above
another single
wall oven.
Cutout –
observe all
dimensions and
requirements.
Cutout –
observe all
dimensions and
requirements.
2” (5.1 cm) Min.
30.5” (77.5 cm)
30” models
27” (68.58 cm)
27” models
Center Line Center Line
Side-by-Side Installations
Install two ovens in separate cutouts.
B
F
GC
A
Cutout Location
from Floor
32-1/2” (82.6 cm)
H
P
R
D
E
Junction
Box
Location
(junction
box may
be located
in adjacent
cabinet)
Cutout Depth
23-1/2”
(59.7 cm) Min.
Opening
Between Inside
Walls Must be
at Least 28-1/2”
(72.4 cm) Wide
NOTE: Allow
1/4” (0.64 cm)
clearances from
side edges of
oven door.
Dimension Dimension Description 27” Single Oven 30” Single Oven
ACabinet Width 27” (68.6 cm) 30” (76.2 cm)
BCutout Width 25” (63.5 cm) min.
251»4” (64.1 cm) max.
281»2” (72.4 cm) min.
285
»8” (72.7 cm) max.
CCutout Height 27
5»8” (70.2 cm) min.
281»8” (71.4 cm) max.
271
»4” (69.2 cm) min.
275
»16” (69.4 cm) max.
D
Clearance from cutout - side edges*
1” (2.5 cm) 11»16” (1.75 cm)
EClearance to Adjacent Corners,
Drawers, Walls, etc., When Door
Is Open
23” (50.8 cm) min. 23” (53.3 cm) min.
FClearance from cutout - top* 1” (2.5 cm) min. 1” (2.5 cm) min.
(1 1»4” (3.2 cm) for PT9050,
ZET1S and ZET1P)
GClearance from cutout - bottom* 1” (2.5 cm) min. 1
1»4” (3.2 cm)
HJunction Box Location 83»4” (22.2 cm) max.
right side only
91
»2” (24.1 cm) max.
right side only
PJunction Box location 5-1/4” (13.34 cm) max. 5-1/4” (13.34 cm) max.
RJunction Box location 2-1/2” (6.35 cm) max. 2-1/2” (6.35 cm) max.
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
2 C CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick,
shim both sides equally to establish the cutout width.
2 D CUTOUT FOR COMBINATION OVENS
(WITH UPPER MICROWAVE OVEN)
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick,
shim both sides equally to establish the cutout width.
Dim. Description 27” Double Oven 30” Double Oven with
Pedestal 30” Double Oven without
Pedestal
ACabinet Width 27” (68.6 cm) 30” (76.2 cm) 30” (76.2 cm)
BCutout Width 25” (63.5 cm) min.
251
»4” (64.1 cm) max. 281»2” (72.4 cm) min.
285»8” (72.7 cm) max. 281»2” (72.4 cm) min.
285»8” (72.7 cm) max.
CCutout Height
4911»16” (126.2 cm) min.
501»8” (127.3 cm) max. 5113
»16” (131.6 cm) min.
5115
»16” (131.9 cm) max. 50 ¼” (127.64cm)
DClearance from cutout - side
edges* 1” (2.5 cm) 11
»16” (1.75 cm) 11
»16” (1.75 cm)
E
Clearance to Adjacent Corners,
Drawers, Walls, etc., When Door
Is Open
23” (50.8 cm) min. 23” (53.3 cm) min. 23” (53.3 cm) min.
FClearance from cutout - top* 1” (2.5 cm) min. 1” (2.5 cm) min.
(11
»4” (3.2 cm) for PT9550,
ZET2S and ZET2P)
1” (2.5 cm) min.
(11
»4” (3.2 cm) for PT9550,
ZET2S and ZET2P)
GClearance from cutout -
bottom* 1” (2.5 cm) min. 11
»4” (3.2 cm) 11
»4” (3.2 cm)
HJunction Box Location 8
3»4” (22.2 cm) max.
right side only 91
»2” (24.1 cm) max. right
side only 91
»2” (24.1 cm) max. right
side only
KCutout Location from Floor 13
1
»4” (33.7 cm) min. 12” (30.5 cm) min. 12” (30.5 cm) min.
PJunction Box location 5-1/4” (13.34 cm) max. 5-1/4” (13.34 cm) max. 5-1/4” (13.34 cm) max.
RJunction Box location 2-1/2” (6.35 cm) max. 2-1/2” (6.35 cm) max. 2-1/2” (6.35 cm) max.
Dim. Description
27” Oven
with Microwave
30” Oven
with Microwave
ACabinet Width 27” (68.6 cm) 30” (76.2 cm)
BCutout Width 25” (63.5 cm) min.
251»4” (64.1 cm) max.
281»2” (72.4 cm) min.
285»8” (72.7 cm) max.
CCutout Height 41
1»8” (104.5 cm) min.
411
»4” (104.8 cm) max.
423
»16” (107.2 cm) min.
421
»4” (107.3 cm) max.
DClearance from cutout -
side edges* 1” (2.5 cm) 11»16” (1.75 cm)
E
Clearance to Adjacent Corners,
Drawers, Walls, etc., When Door
Is Open
23” (58.4 cm) min. 23” (58.4 cm)
FClearance from cutout - top* 1” (2.5 cm) min. 1” (2.5 cm) min.
GClearance from cutout -
bottom* 1” (2.5 cm) min. 1 1»4” (3.2 cm)
HJunction Box Location 83
»4” (22.2 cm) max.
right side only
91
»2” (24.1 cm) max.
right side only
PJunction Box location 5-1/4” (13.34 cm) max. 5-1/4” (13.34 cm) max.
RJunction Box location 2-1/2” (6.35 cm) max. 2-1/2” (6.35 cm) max.
Continue to Section 3.
Continue to Section 2E.
PD
B
C
K
F
G
A
H
R
E
Junction Box
Location
(junction
box may
be located
in adjacent
cabinet)
Cutout Depth
23-1/2”
(59.7 cm) Min.
31-2000964 Rev. 2 03-24 GEA
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
H
R
P
NOTE: Allow
1/4” (0.64 cm)
clearances from
side edges of
oven door.
NOTE: Allow
1/4” (0.64 cm)
clearances from
side edges of
oven door.
Specyfikacje produktu
Marka: | Café |
Kategoria: | Oven |
Model: | CTD90DP2NS1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Café CTD90DP2NS1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Oven Café
8 Października 2024
8 Października 2024
Instrukcje Oven
- Oven Bauknecht
- Oven Ikea
- Oven Samsung
- Oven Bertazzoni
- Oven Electrolux
- Oven DeLonghi
- Oven AEG
- Oven Balay
- Oven Beko
- Oven Teka
- Oven LG
- Oven Küppersbusch
- Oven Smeg
- Oven Gram
- Oven Caso
- Oven Amica
- Oven Gorenje
- Oven Etna
- Oven LERAN
- Oven Sharp
- Oven Russell Hobbs
- Oven Sage
- Oven Tefal
- Oven SilverCrest
- Oven Dometic
- Oven Bosch
- Oven Dash
- Oven Candy
- Oven Whirlpool
- Oven Cramer
- Oven Miele
- Oven Midea
- Oven Lamona
- Oven Severin
- Oven Hisense
- Oven Infiniton
- Oven Medion
- Oven Baumatic
- Oven Black & Decker
- Oven OK
- Oven Adler
- Oven Hoover
- Oven Tesla
- Oven Westinghouse
- Oven Hendi
- Oven Quigg
- Oven Maytag
- Oven GE
- Oven Ardes
- Oven Taurus
- Oven Orbegozo
- Oven Blaupunkt
- Oven Brandt
- Oven Siemens
- Oven Grundig
- Oven Haier
- Oven Jocel
- Oven Hyundai
- Oven Silverline
- Oven Blomberg
- Oven Bimar
- Oven Rowenta
- Oven Concept
- Oven Fisher & Paykel
- Oven ECG
- Oven Indesit
- Oven Ilve
- Oven Viking
- Oven Nodor
- Oven CATA
- Oven Hotpoint
- Oven Kenwood
- Oven V-Zug
- Oven Trisa
- Oven Ariston Thermo
- Oven Zelmer
- Oven Mestic
- Oven PKM
- Oven Cuisinart
- Oven Unox
- Oven Amana
- Oven Dacor
- Oven Hotpoint Ariston
- Oven Bomann
- Oven Moulinex
- Oven PowerXL
- Oven Emerio
- Oven H.Koenig
- Oven Meireles
- Oven Schneider
- Oven Thetford
- Oven Stirling
- Oven MPM
- Oven CDA
- Oven Philco
- Oven Neff
- Oven Corbero
- Oven Zanussi
- Oven Fagor
- Oven Izzy
- Oven Klarstein
- Oven Wolkenstein
- Oven Cecotec
- Oven Artusi
- Oven KitchenAid
- Oven AFK
- Oven Camry
- Oven Steba
- Oven Imperial
- Oven Scarlett
- Oven TriStar
- Oven Exquisit
- Oven Bartscher
- Oven First Austria
- Oven Mitsubishi
- Oven Privileg
- Oven Arçelik
- Oven Hanseatic
- Oven Continental Edison
- Oven Linarie
- Oven Atag
- Oven Rosieres
- Oven Franke
- Oven G3 Ferrari
- Oven Axis
- Oven Westfalia
- Oven Hamilton Beach
- Oven Novy
- Oven Clatronic
- Oven Telefunken
- Oven Ferrari
- Oven Rommer
- Oven Inventum
- Oven SVAN
- Oven Ariete
- Oven Princess
- Oven Innoliving
- Oven Sunbeam
- Oven Euro Appliances
- Oven Waring Commercial
- Oven Caple
- Oven Omega
- Oven Classique
- Oven New Pol
- Oven Kenmore
- Oven Breville
- Oven VOX
- Oven Pelgrim
- Oven Frilec
- Oven Tower
- Oven Rex
- Oven Kernau
- Oven Aspes
- Oven Zerowatt
- Oven Respekta
- Oven Technika
- Oven JennAir
- Oven Frigidaire
- Oven Galanz
- Oven Matrix
- Oven Gemini
- Oven Foster
- Oven Chef
- Oven Rommelsbacher
- Oven Fulgor Milano
- Oven Gaggenau
- Oven Sencor
- Oven Hobart
- Oven Mistral
- Oven Avanti
- Oven Asko
- Oven Kalorik
- Oven Suntec
- Oven Flavel
- Oven Esatto
- Oven BlueStar
- Oven Porter & Charles
- Oven Grunkel
- Oven Becken
- Oven Traeger
- Oven Ignis
- Oven Guzzanti
- Oven Mach
- Oven Edilkamin
- Oven Dualit
- Oven Belling
- Oven De Dietrich
- Oven Sauber
- Oven Constructa
- Oven BLANCO
- Oven Scancool
- Oven Thermador
- Oven Zanker
- Oven Alpina
- Oven Ariston
- Oven Techwood
- Oven Korona
- Oven Saturn
- Oven Progress
- Oven Tomado
- Oven Bellini
- Oven Oster
- Oven Junker
- Oven Iberna
- Oven Valberg
- Oven Scholtes
- Oven Heinner
- Oven Termozeta
- Oven Juno
- Oven Defy
- Oven Blokker
- Oven Trebs
- Oven Nordmende
- Oven Boretti
- Oven Hansa
- Oven Elba
- Oven WLA
- Oven SEB
- Oven Steel Cucine
- Oven Limit
- Oven Ufesa
- Oven Leonard
- Oven Presto
- Oven Lofra
- Oven New World
- Oven Glem Gas
- Oven M-System
- Oven Proctor Silex
- Oven Primo
- Oven Barbecook
- Oven Falcon
- Oven Godrej
- Oven Ices
- Oven Mx Onda
- Oven Team
- Oven Schock
- Oven Stoves
- Oven CaterChef
- Oven Parmco
- Oven Zephir
- Oven Eurotech
- Oven Wolf
- Oven Vestfrost
- Oven Day
- Oven Outdoorchef
- Oven Smev
- Oven Nesco
- Oven Waves
- Oven White And Brown
- Oven Home Electric
- Oven Khind
- Oven Tisira
- Oven Ronco
- Oven Therma
- Oven La Germania
- Oven Luxell
- Oven Oranier
- Oven Leventi
- Oven Rösle
- Oven Riviera And Bar
- Oven Venga
- Oven OBU
- Oven Rival
- Oven Eudora
- Oven Thomas
- Oven Steelmatic
- Oven Kogan
- Oven Mibrasa
- Oven Vulcan
- Oven General Electric
- Oven Pit Boss
- Oven Elin
- Oven WestBend
- Oven Blodgett
- Oven Winia
- Oven Alto-Shaam
- Oven TurboChef
- Oven Simfer
- Oven Merrychef
- Oven Arda
- Oven Girmi
- Oven Eltac
- Oven Roller Grill
- Oven Imarflex
Najnowsze instrukcje dla Oven
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024