Instrukcja obsługi Bowers & Wilkins Performance Series CWM652

Bowers & Wilkins głośnik Performance Series CWM652

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bowers & Wilkins Performance Series CWM652 (3 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

English

CWM6

4.2 If speaker cable is already present in the wall

space, pull the cable down through the aperture. If

speaker cables are not already installed this should be

done at this stage. It is likely that you will need to gain

access through the oor above to route the cables

down into the wall cavity.

Leave enough spare cable through the aperture to

ease connection to the speaker frame, but not so

much that it is likely to buzz or rattle when pushed

back up into the wall space. Approximately 1.0m (3 ft)

is appropriate.

Note: Always use high quality, low resistance

speaker cable. Low resistance is especially

important if the length of cable from ampliﬁer to

speaker exceeds 5m. Your local Bowers & Wilkins

retailer will be able to offer advice on speaker cable

selection if required.

4.3 Now connect the speaker cable to the spring

terminals on the side of the frame. Ensure that the

speaker connection polarity is correct: the cable

connected to the positive terminal on the amplier

should be connected to the red spring terminal on the

frame. Similarly, the cable connected to the negative

terminal on the amplier should be connected to the

black spring terminal on the frame. The diagram above

illustrates cable connection.

Note: If an ampliﬁer is already connected to the

cable it should be switched off while connections

are being made to the frame.

4.4 With the frame connected it may be inserted into

the wall aperture. Ensure that the QuickDogs™ (spring

clamps) are rotated so that they will pass through the

aperture then insert the frame up so that the ange

is ush on the wall. Take care that the cable is not

trapped. Now reach inside the aperture, rotate the

QuickDogs™ outwards and, using two ngers and

thumb, pull each spring clamp downwards so that the

frame is xed securely. There are four QuickDogs™ on

the CWM652 and six on the CWM663 and CWM664.

The diagram above illustrates insertion of the frame.

Note: To release a spring clamp push the metal tab,

located just below the ﬁnger platform, upwards.

4.5 If the frame ange is to be painted it should be

done at this stage. Any conventional, domestic paint

may be applied by brushing, rolling or spraying. Use

the supplied paint mask to avoid getting paint in the

cavity. Painting without using the paint mask risks

contamination of the internal connection terminals or

the grille attachment magnets. The diagram above

illustrates painting using the paint mask.

Note: If the grille is to be painted this should be

done “off-line” before it is ﬁtted.

4.6 The bafe can now be tted into the frame. Ensure

that the connector on the bafe is oriented correctly

with the connector in the frame. The bafe is hinged

into place along its bottom edge and secured at the

top by two push-lock fasteners. Push-lock fasteners

are secured by pushing the head inwards – either

with a thumb or a screwdriver. Please ensure that

the largest groove on the fastener is orientated at a

diagonal, pointing to the corner of the bafe, before

pushing the fastener. As they secure, the fasteners

will click. The bafe will then be secure in the frame.

The diagram above illustrates inserting the bafe and

securing the push-lock fasteners.

Note: Push-lock fasteners are released by turning

anticlockwise with a screwdriver.

4.7 A three position high frequency level switch is

tted to CWM600 series models, on the front face of

the bafe. The centre position of the switch gives a

nominally level frequency response.

The HF+ boost position can be useful where the

listening environment is acoustically absorbent, for

instance where carpets, soft furnishings and curtains

predominate, or where the speakers are covered

by curtains or wall hangings. The HF- cut position

may be preferred where the listening environment is

acoustically reective, for instance where hard oors

and glass predominate. The diagram above illustrates

the level switch and its effect.

= 1x

Specyfikacje produktu

Marka:	Bowers & Wilkins
Kategoria:	głośnik
Model:	Performance Series CWM652

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bowers & Wilkins Performance Series CWM652, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Bowers & Wilkins CWM664 Instrukcja

12 Stycznia 2025

Bowers & Wilkins CT7.3 LCRS Instrukcja

4 Października 2024

Bowers & Wilkins CT8 CC Instrukcja

29 Września 2024

Bowers & Wilkins CDA-16 Instrukcja

29 Września 2024

Bowers & Wilkins CT8.2 LCR Instrukcja

29 Września 2024

Bowers & Wilkins Nautilus 800 Instrukcja

29 Września 2024

Bowers & Wilkins DM600 S3 Instrukcja

24 Września 2024

Bowers & Wilkins BB CCM8.5 Instrukcja

22 Września 2024

Bowers & Wilkins BB CWM8.5 Instrukcja

22 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025

Klipsch PIC-525-T-SC Instrukcja

15 Stycznia 2025