Instrukcja obsługi Boss OC-5

Boss Niesklasyfikowane OC-5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss OC-5 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

* 5100072383- 01*

Owner’s Manual

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate

sheet).

After reading, keep the document(s) where it will be available for immediate reference.

AC adaptor

(PSA series; sold

separately)

Guitar

Bass

English

Guitar Amp

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on an AC adaptor

(BOSS PSA series; sold separately).

* Use only the specied AC adaptor (PSA series; sold

separately), and connect it to an AC outlet of the correct

voltage.

* If the AC adaptor is connected while a battery is installed,

the power supply is drawn from the AC adaptor.

CHECK indicator

The indicator lights when an eect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery

lowers. Replace the battery when the LED is dim or does not light. For

instructions, refer to “Changing the Battery.”

* The CHECK indicator shows whether the eect is on or o.

-1OCT LEVEL knob

This knob adjusts the volume of the sound that is one octave below the

direct sound.

+1OCT LEVEL knob

This knob adjusts the volume of the sound that is one octave above the

direct sound.

Pedal switch

This switch turns the

eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the battery.

* For instructions on changing the battery, refer to “Changing the Battery.”

Panel Descriptions

Precautions When Connecting

• To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

• Once everything is properly connected, be sure to follow the

procedure below to turn on their power. If you turn on equipment

in the wrong order, you risk causing malfunction or equipment

failure.

When powering

up:

Turn on the power to your

guitar amp last.

When powering

down:

Turn o the power to your

guitar amp rst.

• Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Use of Battery

• If operating this unit on battery, please use alkaline battery.

• The life of the included battery may be limited as its primary

purpose was for testing during assembly.

• When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

• If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

Additional Precautions

• When disposing of the packing carton or cushioning material in

which this unit was packed, you must observe the waste disposal

regulations that apply to your locality.

• Do not use connection cables that contain a built-in resistor.

Changing the Battery

1. Hold down the pedal and loosen the

thumbscrew, then open the pedal upward.

Thumbscrew

Battery housing

Pedal

Spring base

Coil spring

Guide

bush hole

Battery

snap cord

Battery

snap

Battery

* The pedal can be opened without detaching the

thumbscrew completely.

2. Remove the old battery from the battery

housing, and remove the snap cord

connected to it.

3. Connect the battery snap to the new battery,

and place the battery inside the battery

housing.

* Be sure to carefully observe the battery’s polarity

(+ versus -).

4. Slip the coil spring onto the spring base on

the back of the pedal, and then close the

pedal.

* Carefully avoid getting the snap cord caught in the

pedal, coil spring, and battery housing.

5. Finally, hold down the pedal while tightening

the thumbscrew into the guide bush hole.

Main Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Alkaline battery (9 V, 6LR61 or 6LF22)

AC adaptor (PSA series: sold separately)

Current Draw

55 mA

* Expected battery life under continuous

use:

Alkaline battery: Approx. 7 hours

These gures will vary depending on

the actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight

(including battery)

440 g

1 lb

Accessories

Owner’s Manual, Leaet (“USING THE

UNIT SAFELY,“ “IMPORTANT NOTES,“ and

“Information“), Alkaline battery (9 V, 6LR61

or 6LF22)

Option

(sold separately) AC adaptor (PSA-series)

• 0 dBu = 0.775 Vrms

• This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

• Roland and BOSS are either registered trademarks or trademarks

of Roland Corporation in the United States and/or other countries.

* The INPUT jack also serves as the power switch. Power is

turned on whenever a plug is inserted into the INPUT jack,

and is turned o when the plug is disconnected. When not

using the unit, you should disconnect any cord connected to

the INPUT jack.

* If you’re using this unit together with other eect units,

connect this unit rst in the chain (directly after the guitar).

If guitar sound processed by an eect is input to this unit, it

might not work correctly.

INPUT jack

This jack accepts input signals coming from a guitar (or bass).

DIRECT LEVEL knob

This knob adjusts the volume of the direct sound.

GUITAR/BASS switch

This switch selects settings that are suitable for a

guitar or a bass.

-2OCT/RANGE knob

The operation depends on the setting of the VINTAGE/POLY

switch.

Switch Explanation

VINTAGE

Operates as the -2OCT LEVEL knob. This knob

adjusts the volume of the sound that is two

octaves below the direct sound.

POLY

Operates as the RANGE knob. Adjusts the

bandwidth of the -1OCT eect.

As you turn this knob toward the right, the

eect applies to a wider range of frequencies

from low to high. As you turn this knob

toward the left, the eect is limited to the

low-frequency range. If this knob is turned all

the way to the left, the eect applies only to

the lowest note of the chord.

OUTPUT jack, DIRECT OUT jack

Use this jack to connect to the input

of your guitar amplier or the input of

additional eect unit.

* Output may vary according to the connections.

VINTAGE/POLY switch

This switch selects the character of the sound.

VINTAGE

Vintage sound that simulates the OC-2.

Play (input) single notes.

POLY

Polyphonic mode that supports chordal

input.

Connection

method Sound that is output

Connect only to

the OUTPUT jack

The direct sound and octave sound

are mixed and output.

Connect to the

OUTPUT jack

and the DIRECT

OUT jack

The octave sound is output from the

OUTPUT jack, and the direct sound is

output from the DIRECT OUT jack.

When the eect is o, the sound is

output only from the DIRECT OUT

jack.

For the USA

SUPPLIER’S DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

OC-5

Guitar Eects

Roland Corporation U.S.

5100 S. Eastern Avenue Los Angeles, CA 90040-2938

(323) 890-3700

Specyfikacje produktu

Marka:	Boss
Kategoria:	Niesklasyfikowane
Model:	OC-5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Boss OC-5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Boss

Boss BCAM60 Instrukcja

5 Października 2024

Boss ME-90B Instrukcja

5 Października 2024

Boss Reverb RV-6 Instrukcja

2 Października 2024

Boss Reverb RV-200 Instrukcja

29 Września 2024

Boss GKC-AD Instrukcja

27 Września 2024

Boss SDE-3000D Instrukcja

27 Września 2024

Boss Modulation MD-500 Instrukcja

27 Września 2024

Boss GT-1000CORE Instrukcja

27 Września 2024

Boss Pocket GT Instrukcja

27 Września 2024

Boss Metal Zone MT-2W Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024