Instrukcja obsługi Boss MR1620

Boss Radia samochodowe MR1620

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss MR1620 (21 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/21
CONTENTS
MR1620W • MR1620S User’s Manual - page 1
U S E R ’ S M A N U A L
MR1620W • MR1620S User’s Manual - page 2
Head unit installation
MR1620W • MR1620S Marine MP3/CD Receiver Packing List
To ensure tha
meets the IPX
Standard, plea
carefully.
1. Remove the
the top of the
beginning the
Fig 1 R
2. Place the tw
provided over
prevent water
Figure 2 Apply
Before installing your new CD Receiver, please unpack the contents and check
that your package contains the following items:
2Head unit installation
4Detaching the front panel
5Removing the head unit
6Remote control installation
Flush mount
6Remote control installation
Surface mount
10 General and tuner controls
14 Remote control
15 CD Playback
15 MP3 playback
16 RDS radio functions
17 PTY station categories
18 Wiring diagram
19 Troubleshooting
20 Specifications
Congratulations on your
purchase of a Marine
MP3/CD Receiver.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
Marine your choice for
marine audio entertainment!
Main unit
Detachable front panel with protective case
Mounting hardware for main unit:
Rear bracket plate
Rear mounting screw
Plain washer
Spring washer
Screw
Hex nut
Removal keys (2)
Wiring harness
Wired remote control
Remote control cable
Mounting hardware for remote control:
Mounting arms (2)
Mounting tube (1)
Machine screws (2)
User’s manual
Warranty card
MR1620W
MR1620S
Fully Mariniz oed MP3-C mpatible
In-Dash CD Receiver
page
RDS Model with
Switchable U nSA/Europea
Frequencies
MR1620W • MR1620S User’s Manual - page 2
Head unit installation
MR1620W • MR1620S User’s Manual - page 3
Before installing your new
CD Receiver, please become familiar
with all the information contained in
this manual.
Choose a mounting location where the
unit will not distract or otherwise
interfere with the pilot’s ability to control
the boat.
Use only the installation parts and
hardware provided with the unit to
ensure proper installation. Using other
parts can cause malfunction and
possible damage to your CD
receiver.
Do not install this unit at an angle in
excess of 30º from horizontal, as it
may affect performance.
Although this unit has been designed
for outdoor use, you can extend its life
if you install it in a location which is
not subject to extreme temperatures,
from such sources as heaters or
exhaust lines. Also, if you see dirt, dust
or debris on a disc or in the CD slot,
remove it with a clean cloth to avoid
pushing it into the player mechanism.
To remove dirt from the faceplate, use
a clean cloth lightly moistened with
filtered water. If the unit is splashed
with water, wipe it off with such a clean
damp cloth before the water has dried
to avoid an accumulation of salts on
the face of the unit.
If properly installed, this unit will meet
the IPX5 Waterproof standard. Please
note that this does NOT mean the unit
is submersible, but will resist being
sprayed and splashed as might occur
in a normal boat cabin.
To ensure that the installation
meets the IPX5 Wat oerpr of
Standard, please follow these steps
carefully.
1. Remove the transport screws from
the top of the enclosure before
beginning the installation.
Fig 1 Remove transport screws
2. Place the two pieces of plastic film
provided over the two screw holes to
prevent water penetration.
Figure 2 Apply plastic film to seal screw holes
Figure 3 Bending the support tabs
3. Insert and tighten the “headless”
support screw into the back of the
head unit where shown.
4. Insert the mounting case for the
head unit into the dashboard. Inspect
the dashboard material to determine
its approximate thickness. Select the
appropriate support tabs and bend
them outward to secure the bracket
in place .(Figure 3)
5. Bend the backstrap to conform to
the mounting case and the dashboard
surface to which you plan to secure
the backstrap (Figure 4). Slide one of
the utility holes on the backstrap onto
the support screw and fasten it with
the spring washer and nut provided.
6. Using the 5 x 25mm screw and the
plain washer, secure the backstrap to
the dashboard surface as shown in
the diagram. Tighten, secure, and
check the overall mounting to be sure
it is safe and will not release in an
emergency stop or other sudden
movement of the vehicle.

Specyfikacje produktu

Marka: Boss
Kategoria: Radia samochodowe
Model: MR1620

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Boss MR1620, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radia samochodowe Boss

Boss

Boss UTV4B Instrukcja

5 Października 2024
Boss

Boss BVD9988B Instrukcja

3 Października 2024
Boss

Boss BV6860BH Instrukcja

3 Października 2024
Boss

Boss BVCP9800W Instrukcja

3 Października 2024
Boss

Boss BVCPA10W Instrukcja

3 Października 2024
Boss

Boss BCPA8W Instrukcja

3 Października 2024
Boss

Boss Elite BEHDIN98 Instrukcja

29 Września 2024
Boss

Boss ATV654 Instrukcja

29 Września 2024
Boss

Boss ATVB6.5R Instrukcja

28 Września 2024
Boss

Boss MR648S Instrukcja

16 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024