Instrukcja obsługi Bosch WZ18NV312-0

Bosch Kamera monitorująca WZ18NV312-0

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bosch WZ18NV312-0 (3 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
MAN-WZ20-04
Important
Please read this document carefully before installation and initial use. Keep for future reference.
• An unregulated power supply can cause damage to the camera.
• Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to Bosch Security
Systems. Inc.
• It is recommended that the camera be used with a monitor that has a CCTV quality 75Ω video impedance level. If your
monitor is switched to a high impedance level, then please adjust accordingly.
• Never direct the camera towards the sun or any bright or reflective light. Doing so may cause smearing on the picture and
possible damage to the CCD
Important Safety Instructions
1. Read these instructions.
2. Keep this instruction.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched e receptacles, and the power particularly at plugs, convenienc
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in a way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
FCC Note
NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. As part of its’ normal
operation this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may
cause interference to radio communications. However, there is no guarantee that interference will not occur on a particular installation. If
the device does cause interference to radio or television reception the user is encouraged to try to correct the interference by one or more
of the following measures:
1) Fit Ferrite beads on all cable to and from the power
supply box, within the box walls.
2) Route the composite cable between the camera and the power supply in steel conduit piping over the entire run of the cable up to and
including connection to a deep conduit base fitted under the camera and a conduit fitting adaptor in the wall of the PSU box.
3) Contact BOSCH Service Center for further advice. .
Installation Guide
WZ18NV312-0 (NTSC) | WZ18PV312-0 (PAL)
MAN-WZ20-04
Precautions
• Do not open or modify
• Do not put objects inside the unit. Make sure that no metal objects or flammable substances enter the camera. This may
cause fire, short-circuits and other damages.
• Be careful when handling the unit. To prevent damage, do not drop the camera or subject it to strong shock or vibration.
• Install the camera away from electric or magnetic fields.
• Protect the camera from humidity and dust.
• Do not subject the unit to high temperature. Be careful when installing close to ceilings, in a kitchen or a boiler room as
heat rises and will affect the camera.
• Dirt can be removed from the camera by wiping it with a clean soft moistened cloth and soft detergent solution.
• The mounting surface material must be strong enough to secure the camera.
Troubleshooting
Before sending the camera for repair, check the list below. If the problem still persists, Bosch Security Systems, Inc.
If no image appears
• Is the coaxial cable firmly attached?
• Is power and voltage at a normal level?
• Is there adequate illumination?
• Is the monitor correctly adjusted?
If the image is unclear
• Is the lens in focus?
• Is the lens dirty?
Installation
MAN-WZ20-04
Camera Positioning
• Use provided alan key from box to
make adjustments
• Locate and loosen all 3 setscrews on
bracket
• Setscrews are shown at (a), (b) and
(c) - picture on the left
• Pan (a), Tilt (b) and Rotate (c)
• Do not pan or twist beyond 360˚ as
shown
• Do not tilt beyond 90 ° as shown
• Do not apply excessive force when
adjusting camera positioning
Installation (cont’d)
Camera Specifications
Part Number WZ18NV312-0 (NTSC) | WZ18PV312-0 (PAL)
Signal Processing Digital signal processing (DSP)
CCD Camera 1/3” LXR CCD with Mechanical Filter
Filter Dual-window mechanical type
Resolution High resolution 550 TVL
Effective Pixels (NTSC) 811 (H) x 508 (V)
Effective Pixels (PAL) 795 (H) x 596 (V)
Night-Time Sensitivity 0 Lux (infrared on)
Day-Night Switching Photocell-controlled, automatic
Electronic Iris (NTSC) 1/60 ~ 1/100,000s
Electronic Iris (PAL) 1/50 ~ 1/100,000s
Output Signal 1V P-P composite video, 75 Ohms
S/N Ratio Greater than 48dB
Gamma 0.45
Lens Varifocal 3.3-12mm
Iris DC auto-iris
Iris Control Externally adjustable auto-iris
Lens Control Externally adjustable zoom, focus
LEDs Even-distribution infrared array
LED control Photocell
Wavelength 850nm
Number of LEDs 18
Voltage 12 to 24 VDC or VAC
Power Draw 4.8W or less (infrared on)
Construction Robust aluminum extrusion
Finish Anodized silver
Operational Temp. -10ºC to +55ºC | -22ºF to +131ºF
Sunshield Included as standard
Power Supply Not included
Weight 0.85kg (1.9lbs)
Dimensions Φ 76mm x 190mm (L)
Environmental Designed to IP66
Subject to change without notice
Contact Information
Americas
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, Pennsylvania 17601
USA
Telephone+1 888-289-0096
Fax +1 585-223-9180
Email: security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven,
The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
apr.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems, Inc. 2009; Data subject to change without
notice.
Lens Adjustments
• Remove cap
• Adjust the iris
level.
• Re-attach cap
(b)
(c)
(a)
Zoom
Focus
DIP switch

Specyfikacje produktu

Marka: Bosch
Kategoria: Kamera monitorująca
Model: WZ18NV312-0

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bosch WZ18NV312-0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Bosch

Bosch

Bosch VDC‑445V04‑10 Instrukcja

7 Października 2024
Bosch

Bosch 7000i Instrukcja

7 Października 2024
Bosch

Bosch FLEXIDOME IP indoor 4000 IR Instrukcja

4 Października 2024
Bosch

Bosch VDI-240 Instrukcja

30 Września 2024
Bosch

Bosch BRS-TOW-4100A Instrukcja

29 Września 2024
Bosch

Bosch BRS-RAC2-8100A Instrukcja

29 Września 2024
Bosch

Bosch DIVAR IP 5000 Instrukcja

29 Września 2024
Bosch

Bosch Smart Home Eyes Instrukcja

26 Września 2024
Bosch

Bosch AutoDome Easy II Instrukcja

25 Września 2024
Bosch

Bosch AUTODOME 4000 Instrukcja

25 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs

Trebs CCD-401C Instrukcja

15 Października 2024
Hikvision

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024
D-Link

D-Link DCS-7510 Instrukcja

15 Października 2024
Ubiquiti Networks

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024
Hikvision

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024
Alecto

Alecto DVC-215IP Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024