Instrukcja obsługi Bosch WZ14N4-0

Bosch Kamera monitorująca WZ14N4-0

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bosch WZ14N4-0 (3 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
MAN-WZ14-02
WZ14N4-0 (NTSC) | WZ14P4-0 (PAL)
Compact Day-Night™ Camera
Important
Please read this document carefully before installation and initial use. Keep for future reference.
• A regulated DC 12V 300mA power supply is recommended for use with this camera for the
best picture and the most stable operations.
• An unregulated power supply can cause damage to the camera.
• Do not attempt to disassemble the camera to gain access to the internal components. Refer
servicing to Bosch Security Systems, Inc.
• It is recommended that the camera be used with a monitor that has a CCTV quality 75Ω video
impedance level. If your monitor is switched to a high impedance level, then please adjust
accordingly.
• Never face the camera towards the sun or any bright or reflective light. Doing so may cause
smearing on the picture and possible damage to the CCD
Important Safety Instructions
1. Read these instructions.
2. Keep this instruction.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the power where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in a way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
FCC Note
NOTE: This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. As part of its’ normal operation this device can
generate radio frequency energy and if not installed and used in accordance with the installation
manual may cause interference to radio communications. However, there is no guarantee that
interference will not occur on a particular installation. If the device does cause interference to radio or
television reception the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Fit Ferrite beads on all cable to and from the power
supply box, within the box walls.
2) Route the composite cable between the camera and the power supply in steel conduit piping over the
entire run of the cable up to and including connection to a deep conduit base fitted under the
camera and a conduit fitting adaptor in the wall of the PSU box.
3) Contact BOSCH Service Center for further advice.
MAN-WZ14-02
Precautions
• Do not open or modify
• Do not put objects inside the unit. Make sure that no metal objects or flammable substances
enter the camera. This may cause fire, short-circuits and other damages.
• Be careful when handling the unit. To prevent damage, do not drop the camera or subject it to
strong shock or vibration.
• Install the camera away from electric or magnetic fields.
• Protect the camera from humidity and dust.
• Do not subject the unit to high temperature. Be careful when installing close to ceilings, in a
kitchen or a boiler room as heat rises and will affect the camera.
• Dirt can be removed from the camera by wiping it with a clean soft moistened cloth and soft
detergent solution.
• The mounting surface material must be strong enough to secure the camera.
Troubleshooting
Before sending the camera out for repair, check the questions below. If the problem persists after
checking these questions, contact Bosch Security Systems, Inc.
If no image appears
• Is the coaxial cable firmly attached?
• Is power and voltage at a normal level?
• Is there adequate illumination?
• Is the monitor correctly adjusted?
If the image is unclear
• Is the lens in focus?
• Is the lens dirty?
Installation
MAN-WZ14-02
Installation (cont’d)
Camera Specifications
Part Number WZ14N4-0 (NTSC) | WZ14P4-0 (PAL)
CCD Camera 1/3” SuperHAD CCD
Resolution 380 TVL
Color / monochrome Video level switching
Effective Pixels (NTSC) 510 (H) x 492 (V)
Effective Pixels (PAL) 500 (H) x 582 (V)
Night-Time Sensitivity 0 Lux (infrared on)
Electronic Iris (NTSC) 1/60 ~ 1/100,000s
Electronic Iris (PAL) 1/50 ~ 1/100,000s
Output Signal 1V P-P composite video, 75 Ohms
S/N Ratio Greater than 48dB
Gamma 0.45
Lens Fixed 3.7mm lens
LEDs Infrared array, photocell-controlled
Wavelength 850nm
Number of LEDs 12
Voltage 12 VDC
Power Draw 250mA maximum
Construction Aluminum extrusion
Finish Anodized silver
Operational Temp. -30ºC to 55ºC | -22ºF to +131ºF
Sunshield Included as standard
Bracketry Pan-tilt bracket included as standard
Power Supply Not included
Weight 0.39kg (0.86lbs)
Dimensions Φ 58.5mm x 90mm (L) | 2.3” x 3.5” (L)
Subject To Change Without Notice.
Contact Information
Americas
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, Pennsylvania 17601
USA
Telephone+1 888-289-0096
Fax +1 585-223-9180
Email: security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven,
The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax: +65 6319 3499
apr.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems, Inc. 2009; Data subject to change without notice.

Specyfikacje produktu

Marka: Bosch
Kategoria: Kamera monitorująca
Model: WZ14N4-0

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bosch WZ14N4-0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Bosch

Bosch

Bosch VDC‑445V04‑10 Instrukcja

7 Października 2024
Bosch

Bosch 7000i Instrukcja

7 Października 2024
Bosch

Bosch FLEXIDOME IP indoor 4000 IR Instrukcja

4 Października 2024
Bosch

Bosch VDI-240 Instrukcja

30 Września 2024
Bosch

Bosch BRS-TOW-4100A Instrukcja

29 Września 2024
Bosch

Bosch BRS-RAC2-8100A Instrukcja

29 Września 2024
Bosch

Bosch DIVAR IP 5000 Instrukcja

29 Września 2024
Bosch

Bosch Smart Home Eyes Instrukcja

26 Września 2024
Bosch

Bosch AutoDome Easy II Instrukcja

25 Września 2024
Bosch

Bosch AUTODOME 4000 Instrukcja

25 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025