Instrukcja obsługi Bosch Logixx 7 WVH28421GB
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bosch Logixx 7 WVH28421GB (16 stron) w kategorii pralka. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/16
1
Safety instructions
The washer dryer is heavy take care when lifting it.
Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer
door).
In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
If in doubt, have the appliance connected by a technician.
Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
Dispose of packaging in an environmentally friendly manner.
This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive
specifies a framework for the return and recycling of waste appliances and is valid â
throughout Europe.
Scope of delivery according to model Humidity in the drum is caused
by the final inspection.â
Depending on the connection
A 2440 mm dia. hose clip may also be required for connecting the siphon (available from â
specialist retailers). : aPage 4âWater connection
Useful tool
Spirit level for aligning the washer dryer.
Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2
Installation area
Stability is important to prevent the machine from wandering.
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
It is to secure the washer dryer feet with holding brackets *. essential â
If installing the appliance on a wooden joist floor
If possible, install the washer dryer in a corner.
Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
It is to secure the washer dryer feet with holding brackets *. essential â
* order no. WMZ 2200, WX 9756â
Hose and cable lengths
Connection on left side Connection on right side or
Note
Note
Note
NoteNote: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
Aqua-Stop extension hose **, approx. 2.50 m.â
Longer supply hose, approx. 2.20 m, for standard model.
** order no. WMZ 2380, WZ 10130â
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
Dimension requirement of kitchen unit:
a = 650 mm b = 620 mm c = 850 mmâ â â , â â â , â â â
Install washer dryer only under a continuous worktop that
is connected firmly to the adjacent cupboards.
The installation area must be well ventilated, otherwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm f = 365 mm, â
Distance between wall and machine: 50 mmâ
~140 cm
~160 cm
~140 cm
~90 cm
~165 cm
~95 cm
max. 100 cm
min. 60 cm
f
e
3
Removing transport bolts
Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
If transporting the appliance subsequently, always re-install the
transport bolts this prevents damage to the machine. Page 6aâ
Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2. Undo and remove all 4 transport bolts.
3. Take the power cord out of the holders. Remove the sleeves.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4
Water connection
Risk of electric shock! Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).â â
To prevent leakage or water damage, follow the instructions in this chapter.
: operate the washer dryer with cold drinking water only.Attention
Do not connect to the mixer tap of a pressureless hot-water heater.
Do not use a used inlet hose. Only use the inlet hose supplied or one which
was purchased from an authorised specialist dealer.
If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strength is no longer guaranteed).
Optimum water pressure in the mains: 1001000 kPa (110 bar)
When the tap is turned on, the water flow is at least 8 l/min.
If the water pressure is higher, install a pressure reducing valve.
Model: Aqua-Stop
Aqua-Secure
Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the
connection points are not leaking.
Attention: the screw connection is under
water mains pressure.
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet: 60100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out
of the sink. â â
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Attention: secure the connection with a 2440 mm dia. hose clip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out
of the drain.â â
3/4
min. 10 mm
m
m
m
mmax.
ax.
ax.
ax.ax.
9
9
9
99 0°
0°
0°
0°0°
max.
max.
max.
max.max.
9
9
9
99 0°
0°
0°
0°0°
3/4
min 10 mm
5
Manufacturer (see Operating instructions) 0312 / 9000 479252
Alignment
High levels of noise, intense vibrations and wandering may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians, if you want
to align the machine by yourself please use a spirit level. â
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level andâ
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Electrical connection
ʑConnect the washer dryer to an alternating current via a correctly installed earthed socket
only.
ʑThe mains voltage and specifications on the washer dryer must match.
aPage 6: âTechnical specifications
ʑFor information about the connected load and required fuse.
aPage 6: âTechnical specifications
ʑEnsure that:
the mains plug and socket are compatible,
the cable cross-section is adequate,
the earthing system has been installed correctly.
ʑA damaged power cord may be replaced by an electrician only.
A replacement power cord is available from customer service.
ʑDo not use multiple plugs/connectors or extension cables.
ʑIf a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
ʑMains plug:
do not insert into/pull out of the socket with damp hands.
do not pull the plug out of the socket by pulling on the power cord.
never pull out the plug while the appliance is in operation.
6
Transportation, e.g. if moving house
Before transporting the washer dryer:
1. Turn off the tap.
2. Release the water pressure in the supply hose.
aPage 8: âFilter in the water inlet hose
3. Drain any residual detergent solution.
aPage 8: âDrain pump
4. Isolate the washer dryer from the power supply.
5. Remove the hoses.
Installing transport bolts:
1. Remove the covers. If necessary, remove the
retainer according to the right picture.
2. Insert all 4 sleeves.
Clamp the power cord into
the holders.
Insert the screws and
tighten.
The transport bolts be removed after transportation. must aPage 3â
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser and start the II Empty Drain ( ) or programme.Spin
Technical specifications
ʑ Dimensions (width x depth x height) 600 x 600 x 850 mm
ʑ Weight 84,5 kg
ʑ
Power supply
Nominal voltage 220240 V, 50 Hzâ
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
ʑ Water pressure 1001000 kPa (110 bar)
ʑ Drain height 60100 cm
ʑ Test programmes According valid European Standard EN50229
1.
2.
7
Care
Machine housing, control panel
Wipe with a soft, damp cloth.
Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Immediately remove laundry and cleaning agent residues.
Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1. Pull out the drawer up to the stop position, press down the latch
on the insert and remove the drawer completely.â â
2. Remove insert: pull insert upwards with finger.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure in place (the cylinder should fit over the
guide pin). â
5. Insert the detergent drawer.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
Leave the washer dryer door open after washing so that the drum can dry.
Rust stains use chlorine-free cleaning agent, not steel wool.
Descaling No laundry in the machine!
This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
After-sales service
ʑ If you cannot rectify the fault yourself aOperating instructions, page 12, 13: What to do if...,
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
ʑThe contact details for all countries can be found in the enclosed after-sales service directory.
ʑPlease give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
Product number Production number
You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
ʑRely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
Risk of electric shock!
Pull out the mains plug!
Risk of explosion! No solvents!
8
Maintenance
Drain pump
Set the programme selector to , disconnect the mains plug.Off
1. Open and remove the service flap.
2. Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose, allow the detergent
solution to flow out. Push the sealing cap back in.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff from
inside and clean the pump. (impeller in the pump must be able to rotate).
4. Clean any residual lye or fluff from the thread of the pump cap
and pumphousing.â
5. Attach the pump cap and screw it on tight until the stop, handle is upright.
Place the drainage hose back in the retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment and start II
the programme. Then select and start a new washing programme Spin
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spin Empty Drainor ( )).
3. Touch Start button and allow the programme to run for approx. 40 seconds.
4. Set the programme selector to . Off Disconnect the mains plug.
Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check if it
is tight.
Risk of scalding!
Allow detergent solution to cool down!
Turn off the tap!
9
Maintenance
Air inlet filter
Set the programme selector to , disconnect the mains plug.Off
1. Open and remove the service flap.
2. Remove the air inlet filter.
3. Clean the fluff on the air inlet filter with water and a brush.
4. Place the air inlet filter back on and close.
5. Place the service flap back on and close.
Aqua-Stop warranty for appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
Contents Page
ʋSafety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋEnvironmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋScope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋInstallation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ʋHose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
ʋBuilt-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . . 2
ʋRemoving transport bolts . . . . . . . . . . . . . . . . . . . . . . . 3
ʋWater connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ʋAlignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋElectrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋTransportation, e.g. if moving house . . . . . . . . . . . . . . . 6
ʋTechnical specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6
ʋCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ʋAfter-sales serevice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ʋMaintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/9
ʋAqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Washer dryer en
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.
Installation maintenance
instructions
Specyfikacje produktu
| Marka: | Bosch |
| Kategoria: | pralka |
| Model: | Logixx 7 WVH28421GB |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Bosch Logixx 7 WVH28421GB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje pralka Bosch
9 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
Instrukcje pralka
- pralka Bauknecht
- pralka Ikea
- pralka Samsung
- pralka Electrolux
- pralka AEG
- pralka Balay
- pralka Beko
- pralka Teka
- pralka LG
- pralka Küppersbusch
- pralka Smeg
- pralka Gram
- pralka Amica
- pralka Gorenje
- pralka Etna
- pralka LERAN
- pralka Sharp
- pralka TCL
- pralka Russell Hobbs
- pralka Simpson
- pralka Candy
- pralka Whirlpool
- pralka Miele
- pralka Midea
- pralka Lamona
- pralka Hisense
- pralka Infiniton
- pralka Singer
- pralka Panasonic
- pralka Nedis
- pralka Baumatic
- pralka Black & Decker
- pralka OK
- pralka Polar
- pralka Adler
- pralka Hoover
- pralka Toshiba
- pralka Westinghouse
- pralka Romo
- pralka Maytag
- pralka GE
- pralka Brandt
- pralka Vivax
- pralka Salora
- pralka Siemens
- pralka Danby
- pralka Grundig
- pralka Haier
- pralka Cylinda
- pralka Jocel
- pralka Hyundai
- pralka Blomberg
- pralka Mesko
- pralka Husqvarna
- pralka Concept
- pralka Fisher & Paykel
- pralka ECG
- pralka Indesit
- pralka Nodor
- pralka CATA
- pralka Dyson
- pralka Hotpoint
- pralka Kenwood
- pralka V-Zug
- pralka Ariston Thermo
- pralka Mestic
- pralka PKM
- pralka Amana
- pralka Hotpoint Ariston
- pralka Bomann
- pralka Ursus Trotter
- pralka Patriot
- pralka Meireles
- pralka Foppapedretti
- pralka Stirling
- pralka MPM
- pralka OneConcept
- pralka CDA
- pralka Philco
- pralka Neff
- pralka CHiQ
- pralka Corbero
- pralka Zanussi
- pralka Ravanson
- pralka Fagor
- pralka Koenic
- pralka Thomson
- pralka Ardo
- pralka Manta
- pralka Pyle
- pralka Wolkenstein
- pralka Cecotec
- pralka Artusi
- pralka KitchenAid
- pralka Icecool
- pralka Camry
- pralka Germanica
- pralka Sôlt
- pralka Nevir
- pralka Exquisit
- pralka Hestan
- pralka Privileg
- pralka Aurora
- pralka Arçelik
- pralka Hanseatic
- pralka Continental Edison
- pralka Rosieres
- pralka Sanyo
- pralka Clatronic
- pralka Telefunken
- pralka Rommer
- pralka Calor
- pralka Inventum
- pralka SVAN
- pralka IFB
- pralka Carson
- pralka Olympia
- pralka Euro Appliances
- pralka Caple
- pralka AEG-Electrolux
- pralka Omega
- pralka Comfee
- pralka Classique
- pralka Bush
- pralka New Pol
- pralka Kenmore
- pralka VOX
- pralka Hiberg
- pralka Frilec
- pralka Benavent
- pralka Element
- pralka Orima
- pralka Rex
- pralka Kernau
- pralka Aspes
- pralka Orion
- pralka Hitachi
- pralka Zerowatt
- pralka Technika
- pralka Vedette
- pralka Seiki
- pralka Frigidaire
- pralka RCA
- pralka Summit
- pralka Electra
- pralka Kelvinator
- pralka Gaggenau
- pralka Avanti
- pralka Asko
- pralka Kalorik
- pralka Zenith
- pralka Flavel
- pralka Esatto
- pralka Signature
- pralka Daewoo
- pralka Porter & Charles
- pralka Kunft
- pralka Robinhood
- pralka Becken
- pralka Scandomestic
- pralka Ignis
- pralka Emilia
- pralka Belling
- pralka De Dietrich
- pralka SanGiorgio
- pralka ZLine
- pralka Eurom
- pralka Arctic Cooling
- pralka Sauber
- pralka Crosley
- pralka Constructa
- pralka Proline
- pralka Euromaid
- pralka Lemair
- pralka Finlux
- pralka Atlas
- pralka Swan
- pralka Zanker
- pralka Kluge
- pralka Acec
- pralka Alpina
- pralka Alluxe
- pralka Aldi
- pralka Ariston
- pralka Aristona
- pralka Techwood
- pralka Palsonic
- pralka Saturn
- pralka Nordland
- pralka Zanussi-electrolux
- pralka John Lewis
- pralka Mabe
- pralka Monogram
- pralka Iberna
- pralka Logik
- pralka Scholtes
- pralka Profilo
- pralka Castor
- pralka Heinner
- pralka Hoover-Helkama
- pralka Defy
- pralka Schulthess
- pralka Otsein-Hoover
- pralka White Knight
- pralka Sunny
- pralka ProAction
- pralka Trebs
- pralka Luxor
- pralka Nordmende
- pralka Friac
- pralka Hansa
- pralka Elba
- pralka WLA
- pralka Ansonic
- pralka Laden
- pralka Everglades
- pralka Freggia
- pralka Listo
- pralka Edesa
- pralka Milectric
- pralka Lloyd
- pralka New World
- pralka Speed Queen
- pralka WhiteLine
- pralka Viva
- pralka Koblenz
- pralka Primo
- pralka Creda
- pralka Atlantic
- pralka Godrej
- pralka Mx Onda
- pralka Kleenmaid
- pralka Hilton
- pralka Essentiel B
- pralka Bendix
- pralka Edy
- pralka Zoppas
- pralka Edgestar
- pralka Parmco
- pralka Eurotech
- pralka Equator
- pralka Vestfrost
- pralka Integra
- pralka Upo
- pralka Lloyds
- pralka SIBIR
- pralka Calex
- pralka Trieste
- pralka Butler
- pralka Café
- pralka ARC
- pralka DEXP
- pralka Lynx
- pralka Teco
- pralka Bluesky
- pralka Otsein
- pralka Videocon
- pralka Khind
- pralka Tisira
- pralka Cobal
- pralka Premier
- pralka Kenny
- pralka Marynen
- pralka Morris
- pralka Laurus
- pralka Eudora
- pralka Thomas
- pralka Linetech
- pralka Kogan
- pralka PolyJohn
- pralka Fensa
- pralka Dishlex
- pralka Simplicity
- pralka Elin
- pralka High One
- pralka Companion
- pralka Codini
- pralka Curtiss
- pralka Winia
- pralka Ocean
- pralka IPSO
- pralka Imesa
- pralka Fisher Paykel
- pralka Arda
- pralka Camec
- pralka DAYA
- pralka Americana
- pralka Horn
- pralka MegaMove
- pralka FAURE
- pralka Novamatic
- pralka KIN
- pralka BSK
- pralka Miele Professional
- pralka Mio Star
- pralka Adora
- pralka Newpol
- pralka Samus
- pralka Dexter Laundry
- pralka Haden
- pralka Howdens
- pralka Drean
- pralka Arthur Martin-Electrolux
- pralka Elektra Bregenz
- pralka Tuscany
- pralka Smart Brand
- pralka Waltham
- pralka Imarflex
Najnowsze instrukcje dla pralka
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024