Instrukcja obsługi Blaze BLZ-PROIR

Blaze Rożen BLZ-PROIR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blaze BLZ-PROIR (3 stron) w kategorii Rożen. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

CALIFORNIA PROPOSITION 65 WARNING

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

which are known to the State of California to cause cancer and birth defects or other reproductive harm.

For more information go to: www.P65Warnings.ca.gov

How to Replace a Conventional Burner with an Infrared Sear Burner

1. To install the optional infrared burner, begin by first removing the far left cooking grid, flame

stabilizing g izing grid will not be re installed over the burner. rid and heat zone divider. The Flame stabil -

2. Remove the conventional burner by removing the cotter pin that holds it in place. The pin is located

on the bottom rear of the burner and is accessible from the outside rear of the grill. Use needle nose

plyers to remove the cotter pin. Once removed, remove the conventional burner.

3. Remove the crossfire panel. The crossfire panel is a downward U shaped channel located between the

burners towards the rear of the burners. The y unscrewing the fastener crossfire panel is removed b

under the channel which holds it in place. The most commonly used fastener can be removed with a

metric #4 Allen wrench included with the sear burner.

4. Install the infrared burner into the grill in the same way that the conventional burner installed with

the male post on the rear of the burner resting in the opening in the grill and the chassis cylindrical

venture tube installing around the valve stem in the front. Note: IT IS CRITICAL THAT THE FRONT END OF

THE INFRARED BURNER IS INSTALLED APPROPRIATELY ONTO THE GAS VALVE TO ENSURE THE GAS

FLOWS SAFELY INTO THE BURNER.

Depending on which series of grill, the included spacer might be needed to allow the burner to mount

into the grill body securely. (See figure below)

This is recognized by the burner not completely lowering into place where the male post seats at the

opening in the grill chassis. If so, place the spacer n as show below and install the.

5. With either of the above configurations, replace the cotter pin to hold the burner firmly in place.

6. Replace the heat zone divider and cooking grid BUT NOT THE FLAME STABALIZING GRID.

7. Burn off your sear burner on high before the first use. It is normal to see it smoke as it burns off the

oils from manufacturing. Your burner will also discolor and the mesh plate on top will also flex slightly in

certain areas. Burn off until it is finished smoking (roughly 5 minutes).

For additional information, 9510 or go to Blaze contact your dealer or Blaze - -at 866 976 grills.com.

Preheating the infrared burner

Always preheat the entire grill before cooking. If the grill is already hot from cooking, you should still

preheat the infrared burner for 3 minutes on high. Never place food over the burner until it is fully

preheated to avoid clogging the small ports and damaging the burner from grease drippings and food

particles.

Infrared Burner Cleaning

To keep your infrared burner operating at maximum performanc after each use tue, rn the burner on

high for 5 lid open. This allows any food particles or grease drippings to burn away. - 7 minutes with the

Once your grill has cooled completely, use a soft brush or vacuum to remove any ash accumulation on

the burner if necessary.

Sear Burner Tips:

• The sear burner has a series of ceramic tiles producing the infrared energy. Be careful when

installing/removing and storing the burner as to not crack the tiles. Jarring of the burner could

break the tiles.

• Avoid pouring marinades over the top of the meat positioned above the sear burner. The large

volume of liquid pouring on the hot ceramic plates could damage the plates or clog the burner’s

gas ports.

• The sear burner is made for high temperature cooking and is best run in the high position. For

thicker steaks or those cooked to a we temperature, it might be preferred to sear the ll- done

meat over the infrared burner then move it to a cooler or finishing side of the grill to complete

cooking. This can be accomplished by having a conventional main burner section of the grill

running at a low setting. This technique can improve the crust of the steak.

Contact information

Blaze Outdoor Products:

6620 Greenwell Springs Road

Baton Rouge, LA 70805 USA

Phone: 866- - 976 9510

Email: Customerservice@blazegrills.com

Website: www.blazegrills.com

Specyfikacje produktu

Marka:	Blaze
Kategoria:	Rożen
Model:	BLZ-PROIR

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Blaze BLZ-PROIR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Rożen Blaze

Blaze BLZ-GRIDDLEIJ Instrukcja

16 Września 2024

Blaze BLZ-36-VHOOD Instrukcja

15 Września 2024

Blaze BLZ-4 Instrukcja

15 Września 2024

Blaze BLZ-GP10 Instrukcja

15 Września 2024

Blaze BLZ-3 Instrukcja

14 Września 2024

Blaze BLZ-GP12 Instrukcja

14 Września 2024

Blaze BLZ-PBLTELP Instrukcja

13 Września 2024

Blaze BLZ-GP11 Instrukcja

13 Września 2024

Blaze BLZ-4CHAR Instrukcja

11 Września 2024

Blaze Professional BLZ-2PRO-LP Instrukcja

11 Września 2024

Instrukcje Rożen

Najnowsze instrukcje dla Rożen

Barbecook Siesta 210 Instrukcja

12 Października 2024

Tefal CB2231 Easy Grill Comfort Instrukcja

10 Października 2024

Roesle MAGNUM PRO G3 Instrukcja

9 Października 2024

Roesle No.1 F60 AIR Instrukcja

9 Października 2024

Roesle Smoker No.1 F50-S Instrukcja

9 Października 2024

Roesle Videro G4 Instrukcja

9 Października 2024

Grill Guru Classic Large Instrukcja

9 Października 2024

Euro Appliances EAL1200RBQBL Instrukcja

9 Października 2024

Euro Appliances EAL900RBQBL Instrukcja

9 Października 2024

XO GPOWER60K Instrukcja

8 Października 2024