Instrukcja obsługi Black Box LPH008A-R2

Black Box przełącznik LPH008A-R2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black Box LPH008A-R2 (1 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
Link eight 10-/100-/1000-Mbps PoE+ devices to
this tough, industrial-grade switch’s RJ-45
ports.
Delivers PoE+ power to remote powered devices, including IP
cameras, Wi-Fi access points, and VoIP phones.
8-Port Hardened Gigabit PoE+ Switch Quick Start Guide
LPH008A
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) FREE technical support 24 hours a day, 7 days a
week: Call 724-746-5500 or fax 724-746-0746 Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Customer
Support
Information
NOM Statement
724-746-5500 | blackbox.com
LPH008A
Chapter 3: Operation
724-746-5500 | blackbox.com
LPH008A
© Copyright 2014. Black Box Corporation. All rights reserved. Black Box
® and the Double Diamond
logo are registered trademarks of BB Technologies, Inc. UL is a registered trademark of
Underwriters Laboratories. Any third-party trademarks appearing in this manual are acknowledged
to be the property of their respective owners.
FREE! Live, 24/7 Tech Support is just 60 seconds away.
724-746-5500 | blackbox.com
LPH008A, version 1
FCC and IC RFI Statements; Trademarks
Chapter 1: Overview; Chapter 2: Hardware Installation
724-746-5500 | blackbox.com Page 2
LPH008A
1.3 Hardware Description
Figure 1-1 shows the Hardened Gigabit PoE+ Switch’s front panel. Table 1-1
describes its components.
Figure 1-1. Front panel.
Table 1-1. LPH008A components.
Component Description
(2) Power LEDs Link to 10-/100-/1000-Mbps Ethernet devices
(1) Power Fault LED s when power to the switch is onLight
(8) Link/Act. LEDs Lights when the port is operating
(8) Power Injected LEDs Lights when the port is using PoE+
(8) Gigabit LAN ports Link to PoE+ devices
Chapter 2: Hardware Installation
724-746-5500 | blackbox.com Page 3
LPH008A
Chapter 3: Operation
724-746-5500 | blackbox.com Page 4
LPH008A
Chapter 1: Overview
724-746-5500 | blackbox.com Page 1
LPH008A
1. Overview
1.1 Introduction
The Hardened Gigabit PoE+ Switch has eight 10/100/1000BASE-TX RJ-45
Ethernet ports and two Power LEDs. It supports Power over Ethernet, which
transmits electrical power, along with data, to remote devices over standard
twisted-pair cable in an Ethernet network. The switch uses a 5-pin terminal
block power connector.
NOTE: The switch should be mounted on a well-grounded place, such as a
metal panel.
1.2 What’s Included
Your package should include the following items. If anything is missing or dam-
aged, contact Black Box Technical Support at 724-746-5500 or info@blackbox.
com.
• (1) Hardened Gigabit PoE+ Switch
• (1) 5-pin terminal block for power input
• This user’s manual
Optional accessories:
• Wallmount kit (45.4" [2.3 cm] thick)
2. Hardware Installation
Step 1: Installing the Switch on a DIN Rail or Wall
Refer to the illustrations below to mount the switch on a DIN rail or wall.
DIN rail
installation
Wallmount
installation
Figure 2-1. DIN rail or wallmount installation.
Step 2: Connecting the Power
Refer to the illustration below to connect the power to the switch.
Step 3: Connecting the Network Devices
• Connect your devices using standard UTP/STP cable with RJ-45 connectors to the
switch. (For the cable wiring diagrams, refer to the pin assignment in Figure 3-2.)
• The corresponding RJ-45 LED will light if the Ethernet connection is linked
successfully.
• The LED will blink while the switch transfers data.
UL® Notice for Power Supply
Use a power supply marked with “LPS,” “Limited Power Source,” or “Class 2” with
output rate 24–36 VDC (5 A maximum at 24 VDC).
3. Operation
3.1 LED Indicators
LED indicators are located on the front panel of the switch. See Table 1-1.
3.2 Configuration and Setting Methods
No configuration and setting methods are needed.
3.3 Network Connector Pin Assignments
Table 3-2. RJ-45 connector pinout.
Pin
MDI
(1000BASE-T)
MDI
(10/100BASE-T)
1 TP1+ TX+
2 TP1- TX-
3 TP2+ RX+
4 —TP3+
5 —TP3-
6 TP2- RX-
7 —TP4+
8 —TP4-
RJ-45 8-pin straight-through wiring RJ-45 8-pin crossover wiring
Switch PC (NIC) Switch Switch
3 1 ---------------------------- 3 3 ----------------------------
6 2 ---------------------------- 6 6 ----------------------------
1 3 ---------------------------- 1 1 ----------------------------
2 6 ---------------------------- 2 2 ----------------------------
4 7 ---------------------------- 4 4 ----------------------------
5 8 ---------------------------- 5 5 ----------------------------
7 4 ---------------------------- 7 7 ----------------------------
8 5 ---------------------------- 8 8 ----------------------------
Table 3-2. PoE pin definition.
Pin Pin10/100BASE-T(X) PSE RJ-45 port 1000BASE-T PSE RJ-45 port
1 1TD+ with PoE power input + BI_DA+ with PoE power input +
2 2TD- with PoE power input + BI_DA- with PoE power input +
3 3RD+ with PoE power input - BI_DB+ with PoE power input -
6 4RD- with PoE power input - BI_DC+
4 5Not used BI_DC-
5 6Not used BI_DB- with PoE power input
7 7Not used BI_DD+
8 8Not used BI_DD-
FEDERAL COMMUNICATIONS COMMISSION AND
INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used
properly, that is, in strict accordance with the manufacturer’s instructions, may cause inter ference to radio
communication. It has been tested and found to comply with the limits for a Class A computing device in
accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable
protection against such interference when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which case the user at his own expense will
be required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set
out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par
Industrie Canada.
Warranty and Return Information
If you determine that your LPH008A is malfunctioning, do not attempt to alter or
repair the unit. It contains no user-serviceable parts. Contact Black Box Technical
Support at 724-746-5500 or info@blackbox.com.
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete description,
including the nature and duration of the problem, when the problem occurs, and
any particular application that, when used, appears to create the problem or make
it worse.
RJ-45
connector
Figure 3-1. RJ-45 connector.
Figure 3-2. RJ-45 straight-through and
crossover wiring diagrams.
24–36 VDC 24–36 VDC

Specyfikacje produktu

Marka: Black Box
Kategoria: przełącznik
Model: LPH008A-R2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Black Box LPH008A-R2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Black Box

Black Box

Black Box KV9604A Instrukcja

4 Października 2024
Black Box

Black Box ACX300-R Instrukcja

4 Października 2024
Black Box

Black Box ACR1000A-CTL-192 Instrukcja

24 Września 2024
Black Box

Black Box ACR1000A-CTL-288 Instrukcja

24 Września 2024
Black Box

Black Box LGB5510A Instrukcja

24 Września 2024
Black Box

Black Box AVS-HDB-4KO Instrukcja

24 Września 2024
Black Box

Black Box ACR1000A-R-R2 Instrukcja

24 Września 2024
Black Box

Black Box LGH1006A Instrukcja

24 Września 2024
Black Box

Black Box DTX1002-T Instrukcja

10 Września 2024
Black Box

Black Box DCX3000-DVR Instrukcja

10 Września 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Powerfix

Powerfix PSSS 2 A1 Instrukcja

14 Stycznia 2025
INOGENI

INOGENI CAM230 Instrukcja

14 Stycznia 2025
Schneider

Schneider CCT15225 Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-5248P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2624P Instrukcja

14 Stycznia 2025
Luxul

Luxul XGS-1005 Instrukcja

14 Stycznia 2025
Luxul

Luxul AGS-1008M Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-1208P Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-7048P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2600 Instrukcja

14 Stycznia 2025