Instrukcja obsługi Black & Decker WM500

Black & Decker Niesklasyfikowane WM500

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker WM500 (18 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/18
Workmate®500
Copyright © 2004 Black & Decker Printed in China
Cat. No. WM500 Form No. B&D 588974-02, Rev. 1 (SEPT. ‘04)
588974-02,01,WM500 9/24/04 11:19 AM Page 1
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL .1-800-54-HOW-TO (544-6986)
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE.
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR
COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
(544-6986)
I
MPORTANT SAFETY INSTRUCTIONS
WARNING:
1. Do not load with more than 350 lbs.(160 kg) in Workmate mode and 125 lbs.(57 kg)
in Hand Cart mode.
2. Do not apply an unbalanced load which could cause the Workmate to tip over.
3. Do not step on or stand on Workmate. Do not use the Workmate as a stepladder
or standing platform.
4. Do not store Workmate outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the Swivel Grips.
6. Be sure that the legs are fully opened and that the Transition Lever and Toe Plate
Slider locks in position. Secure Hand Cart loads to steel frame members as
necessary.
7. When using a power tool with the Workmate, follow the safety instructions in the
tool’s instruction manual.
8. Always wear safety glasses when operating power or hand tools.
9. An even pressure of the Vise Jaws on the workpiece is essential. Tighten both
Vise Hand Cranks uniformly.
10. Cutting or drilling into work surface may result in striking metal jaw support below,
damaging tool or work center.
11. Caution required when using high temperature tools (heat guns, torch, solder
iron, etc.). May damage work surface and reduce clamping capability.
WARNING: This product contains chemicals, including lead, known to the
State of California to cause cancer, and birth defects or other reproductive harm.
Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
NOTE! The assembly of the Workmate should take approximately 1 hour.
Before you proceed to assemble you will need the following tools.
1 - Hammer
1 - Phillips Screwdriver
1 - Nut Driver (supplied –item Oof Fig.1))
1 - Combination wrench (supplied) (not shown)
Fig. 1: Unpack
Important: Check that you have received all the parts.
Remove the contents of the carton. The following components are in the carton.
(A) 1 - Frame assembly 1 - Parts bag containing:
(B) (G)2 - Vice Screw Packing Pieces 2 - M6 x 36.5mm bolts
(installed to C)(H) 2 - M6 x 30mm bolts
(C) (I)2 - Vise Brackets 4 - M6 Locking Nuts
1
588974-02,01,WM500 9/24/04 11:19 AM Page 2
2
(D) (J)1 - Front Vise Jaw 4 - M8 Bolts
(E) 1 - Rear Vise Jaw (K) 4 - Swivel Grips
(F) (L)2 - Wheels 2 - Spring Pins
(M) 2 - Vise Hand Cranks
(N) 2 - Snap-in Knobs
(O) 1 - Nut Driver
(P) 2 - M8 Wheel Nuts
(Q) 2 - Flat Washer
(R) 2 - Vise Screw Protectors
(not shown) 1 - Combination Wrench
Assembly:
WARNING: Wear eye protection while assembling Workmate.
Fig. 2 & 3: Frame Assembly
1. Pick up the Frame Assembly Fig. 2: (A) as shown. Place foot on the lower portion of
the assembly and push the Transition Lever to the right to unlock the unit.
2. While holding the Transition Lever in the unlocked position, lift up on the upper cross
member until it is fully extended.
3. Rotate the upper cross member toward you and push back on the lower leg
assembly shown.
4. Fig. 3: Continue to push down on the upper cross member until the unit locks in the
fully open position.
5. Note! Make sure that the locking pin, is engaged and locked into the opposite frame
hole – a click sound will be heard when locked in place.
Fig. 3: Wheel Assembly
1. Using Wheels , M8 Wheel Nuts and Flat Washers , assemble to the axles as(F) (P) (Q)
shown.
2. Tighten the M8 Wheel Nuts using the Nut Driver (O).
Fig. 4: Assembly of the Vise Brackets
1. Assemble the left hand Vise Bracket as shown (Each bracket is stamped either (C)
LH or RH).
2. Insert one M6 x 36.5mm Bolt (G) through the rear leg of Frame Assembly, then
through the rear of the Vise Bracket as shown. Using a Phillips screwdriver and a
Combination Wrench, tighten the M6 Lock Nut (I) onto the bolt.
3. Assemble the front leg of the Frame Assembly to the front of the Vise Bracket (C) as
shown.
4. Insert one M6 x 30 mm Bolt (H) completely through the front leg assembly and then
through the hole in the side of the Vise Bracket as shown. Thread an M6 Lock Nut
(I) onto the end of the bolt and tighten with a Combination Wrench and Phillips
screw driver.
5. Repeat for the right side (RH) Vise Bracket.
Fig. 5: Assembling the Front and Rear Vise Jaws
1. Thread the M8 bolts through the mounting holes located on the top side of the (J)
Front Vise Jaw.
2. While holding the Vise Screw and Pivot Nut up from the underside of the tilt bracket,
thread the M8 Bolt into the mounting hole in the pivot nut.
3. Tighten the M8 Bolts using the Nut Driver (O) (or Combination Wrench provided).
4. Align and install the locating boss on the underside of Rear Vise Jaw with the (E)
locating hole (larger of the two holes) on the Vise Bracket.
5. Insert the two remaining M8 Bolts (J) through the mounting holes located on the top
side of the Rear Vise Jaw and thread into the mounting holes of the Vise Brackets.
6. Tighten the M8 Bolts using the Nut Driver (O) (or Combination Wrench provided)
588974-02,01,WM500 9/24/04 11:19 AM Page 3

Specyfikacje produktu

Marka: Black & Decker
Kategoria: Niesklasyfikowane
Model: WM500

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Black & Decker WM500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Black & Decker

Black & Decker

Black & Decker WM600SC Instrukcja

14 Października 2024
Black & Decker

Black & Decker BDC33L Instrukcja

8 Października 2024
Black & Decker

Black & Decker BPZ12 Instrukcja

3 Października 2024
Black & Decker

Black & Decker WM541 Instrukcja

2 Października 2024
Black & Decker

Black & Decker BEBLV230 Instrukcja

1 Października 2024
Black & Decker

Black & Decker BDS300 Instrukcja

30 Września 2024
Black & Decker

Black & Decker HHVJ315JDP07 Instrukcja

29 Września 2024
Black & Decker

Black & Decker KSTR8 Instrukcja

25 Września 2024
Black & Decker

Black & Decker RC860 Instrukcja

22 Września 2024
Black & Decker

Black & Decker HHVJ315JDP27 Instrukcja

21 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024