Instrukcja obsługi Black & Decker TV200
Black & Decker
Wiertarka
TV200
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker TV200 (20 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/20
1
EN G L I S H
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire
and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create
sparks which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.
Electrical Safety
• Do not abuse the cord. Never use the cord to carry the tool. Keep
cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords may create a fire.
• A battery operated tool with integral batteries or a separate battery
pack must be recharged only with the specified charger for the
battery. A charger that may be suitable for one type of battery may
create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery
pack. Use of any other batteries may create a risk of fire.
Personal Safety
• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention
while operating power tools may result in serious personal injury,
1 - 8 0 0 - 5 4 4 - 6 9 8 6
INSTRUCTION
MANUAL
KEY INFORMATION YOU SHOULD KNOW:
•Drill must be charged for 16 hours before initial use.
•Charger may hum; batteries or charger may become warm
during charging.
•Tighten chuck using all three holes.
6.0 Volt 2-Speed Cordless Drill
TV200
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.
SAVE THIS
MANUAL FOR
FUTURE REFERENCE.
If you have any questions, call
1-800-544-6986.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
*TV200 / 390001 11/14/03 7:28 AM Page 1
1
2
• Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure switch is in the locked or off
position before inserting battery pack. Carrying tools with your finger
on the switch or inserting the battery pack into a tool with the switch
on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A
wrench or a key that is left attached to a rotating part of the tool may
result in personal injury.
• Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enable better control of the tool in
unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-
skid safety shoes, hard hat, or hearing protection must be used for
appropriate conditions.
Tool Use and Care
• Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control.
• Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot
be controlled with the switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked
or off position before making any adjustments, changing
accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal
objects like: paper clips, coins, keys, nails, screws or other small
Depress for reverse (this side)
Enfoncer pour la marche arrière (de ce côté )
Oprima para reversa (desde el lado izquierdo)
Depress for forward (other side)
Enfoncer pour la marche avant (de l'autre côté )
Oprima para marcha hacia adelante (desde el lado derecho)
EN G L I S H
ESPECIFICACIONES
Cargador: 120V, 60 Hz, 8W
Salida: 11Vac, 130mA
2
*TV200 / 390001 11/14/03 7:28 AM Page 2
3
EN G L I S H
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause sparks,
burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edge are less likely to bind and are
easier to control.
• Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If
damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may create a
risk of injury when used on another tool.
Service
• Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel may result
in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may
create a risk of shock or injury
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its
own cord. Contact with a "live" wire will also make exposed metal
parts of the tool "live" and shock the operator.
WARNING: Use of this tool can generate dust containing chemicals
known to cause cancer, birth defects or other reproductive harm. Use
appropriate respiratory protection.
The label on your tool may include the following symbols.
V ............volts
A ............amperes
Hz ..........hertz
W............watts
min ..........minutes
............alternating current
........direct current
no............no load speed
............Class II Construction
…/min ....revolutions or reciprocation per minute
............earthing terminal
..........safety alert symbol
Charging the Drill
Before attempting to charge your drill, thoroughly read ALL of the safety
instructions. To charge your drill, follow the steps below.
1. Remove any accessories from the chuck.
2. Plug the output cord of the charger into the socket in the drill
handle.
3. Plug the charger into any standard electrical outlet.
4. Allow the tool to remain in this condition for 16 hours.
Important Charging Notes
1. After normal usage, your drill should be fully charged in 16 hours
or less. Your drill was sent from the factory in an uncharged
condition. Before attempting to use it, it must be charged for at
least 16 hours.
*TV200 / 390001 11/14/03 7:28 AM Page 3
Specyfikacje produktu
| Marka: | Black & Decker |
| Kategoria: | Wiertarka |
| Model: | TV200 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Black & Decker TV200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wiertarka Black & Decker
13 Października 2024
10 Października 2024
8 Października 2024
8 Października 2024
4 Października 2024
29 Września 2024
25 Września 2024
20 Września 2024
20 Września 2024
19 Września 2024
Instrukcje Wiertarka
- Wiertarka AEG
- Wiertarka Worx
- Wiertarka Kawasaki
- Wiertarka Milwaukee
- Wiertarka Bosch
- Wiertarka Yato
- Wiertarka Parkside
- Wiertarka Global
- Wiertarka Toolcraft
- Wiertarka Festool
- Wiertarka Panasonic
- Wiertarka Bavaria By Einhell
- Wiertarka Stanley
- Wiertarka Scheppach
- Wiertarka Proxxon
- Wiertarka Ribimex
- Wiertarka Hazet
- Wiertarka RIKON
- Wiertarka DeWalt
- Wiertarka Einhell
- Wiertarka Genesis
- Wiertarka Hyundai
- Wiertarka Silverline
- Wiertarka Makita
- Wiertarka Ozito
- Wiertarka RYOBI
- Wiertarka Flex
- Wiertarka GO/ON
- Wiertarka DEDRA
- Wiertarka Baumr-AG
- Wiertarka Biltema
- Wiertarka Hilti
- Wiertarka Max Bahr
- Wiertarka Trotec
- Wiertarka Dremel
- Wiertarka Handwerk
- Wiertarka Meec Tools
- Wiertarka Güde
- Wiertarka Bavaria
- Wiertarka Mafell
- Wiertarka Delta
- Wiertarka DURO PRO
- Wiertarka McKenzie
- Wiertarka Westfalia
- Wiertarka Ergotools Pattfield
- Wiertarka Fein
- Wiertarka Ferm
- Wiertarka Hitachi
- Wiertarka Herkules
- Wiertarka Craftsman
- Wiertarka Fieldmann
- Wiertarka Ridgid
- Wiertarka PowerPlus
- Wiertarka Alpha Tools
- Wiertarka Vonroc
- Wiertarka Powerfix
- Wiertarka HiKOKI
- Wiertarka Workzone
- Wiertarka Porter-Cable
- Wiertarka Metabo
- Wiertarka Cotech
- Wiertarka Skil
- Wiertarka Kinzo
- Wiertarka Tryton
- Wiertarka Sun Joe
- Wiertarka Tacklife
- Wiertarka Luxor
- Wiertarka Maktec
- Wiertarka Steren
- Wiertarka Bort
- Wiertarka Tanaka
- Wiertarka Malmbergs
- Wiertarka Power Craft
- Wiertarka Eibenstock
- Wiertarka Topcraft
- Wiertarka Gamma
- Wiertarka Carat
- Wiertarka Kress
- Wiertarka Duro
- Wiertarka Berner
- Wiertarka Varo
- Wiertarka Defort
- Wiertarka Max
- Wiertarka Truper
- Wiertarka Bruder Mannesmann
- Wiertarka Powerblade
- Wiertarka Meister Craft
- Wiertarka Rupes
- Wiertarka Batavia
- Wiertarka Protool
- Wiertarka Economy
- Wiertarka Holzmann
- Wiertarka Graphite
- Wiertarka Huvema
- Wiertarka Black Decker
- Wiertarka Stomer
- Wiertarka Elu
- Wiertarka Blucave
- Wiertarka Ecomac
- Wiertarka Lux Tools
- Wiertarka Kreg
- Wiertarka Sthor
- Wiertarka Verto
- Wiertarka Wurth
- Wiertarka Spit
- Wiertarka Rok
- Wiertarka Profitech
- Wiertarka Narex
- Wiertarka Baier
- Wiertarka RUKO
- Wiertarka Felisatti
- Wiertarka Robust
- Wiertarka Einhell Bavaria
- Wiertarka MyTool
- Wiertarka G-Technology
- Wiertarka Stalco
Najnowsze instrukcje dla Wiertarka
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
12 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024