Instrukcja obsługi Black & Decker GL535

Black & Decker Podcinacz GL535

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker GL535 (8 stron) w kategorii Podcinacz. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Grass Trimmer

Congratulations!

Your purchase of this Black & Decker Reflex

® grass

trimmer and lawn edger assures you of years of

problem free trimming. The Reflex® not only trims

grass and edges the lawn (GL540), it also has a

unique totally automatic line feed system. You do

nothing - the Reflex® system means non-stop

trimming; by the use of a simple mechanism it

senses when the line has worn and, when needed,

automatically feeds out line to its optimum cutting

length. You just switch the unit on and trim.

Description

Following is a list of the parts that will be mentioned

in this instruction leaflet and are shown in the

appropriate diagrams:

1Body (1)

Secondary handle (2)

Trigger switch (3)

Switch handle (4)

Supply cord restraint (5)

Power inlet or supply cord (6)

Edge conversion button (GL540) (7)

Line trimming blade (8)

Cutting line (9)

Guard (10)

2Guard retaining lugs (11)

Guard screw (12)

Guard screw hole (13)

Front edge (14)

4Spool cover (15)

Spool cover tab (16)

Spool housing (17)

Eyelet (18)

5Spool (19)

6Arrow (20)

Line retaining hole (21)

7Lever (22)

Instruction Manual

Safety instructions

Read all of this manual carefully, observing all

the recommended safety instructions before,

during and after using your machine. Maintain

your machine in good working order.

Familiarise yourself with the controls on your

machine before attempting to operate it, but

above all, be sure you know how to stop

your machine in an emergency.

Retain this manual and all other literature

supplied with your machine for future

reference.

Electrical connection

• Your machine is designed for use on AC

(mains) electrical supplies only. Do not

attempt to use on any other supply.

• Plug your machine into a power point,

never in a light socket.

• Do not leave your machine unattended

whilst it is connected to the electrical supply.

• Always switch off and remove the plug

from the mains before cleaning,

inspecting or adjusting any part of the

trimmer, or if the supply cord has

become damaged or entangled.

Double insulation

Your machine is double insulated. This

means that all external metal parts are

electrically isolated from the power supply.

This is achieved by placing an extra

insulation barrier between the electrical and

mechanical parts. Double insulation means

greater electrical safety and obviates the

necessity of having the machine earthed.

Power supply cord

• The power supply cord should be

regularly inspected for signs of damage or

ageing and only used if in good condition.

• Always keep the power supply cord

away from the cutting line (9), be aware

of its position at all times.

• Never carry your machine by the cord or

jerk the cord to remove the plug from the

socket. Keep the cord away from heat,

oils and sharp edges.

• Have damaged cords replaced

completely by your nearest Black & Decker

service centre. Do not attempt to do this

yourself as the switch handle is not

customer serviceable.

ENGLISH

Cutting line

• Take care against injury from line trimming

blade (8) during unpacking and assembly

and any excess line which may be cut off

when the trimmer is first operated.

• The cutting line (9) will continue to run for

a short time after releasing the trigger

switch. Under no circumstances should

you attempt to stop the cutting line,

always allow it to stop on its own.

• Never fit metal cutting line.

Clothing

• Always wear safety glasses when using

your machine.

• To protect your feet, always wear stout

shoes or boots (not bare footed or

wearing open sandals).

• Wear long trousers to protect your legs -

any debris left on the lawn or cutting path

may be picked up and ejected by the

cutting line.

• Use ear protection if the sound level

seems uncomfortable when using

your machine.

Using your machine

• Always use your machine in the manner

outlined in this manual. Your machine is

designed to be used in an upright

position and if it is used in any other way

an injury may result.

• Before using your machine, disconnect it

from the electrical supply and visually

inspect the rotating parts for damage.

Also, check that the spool assembly

is secure.

• Always check that your lawn or cutting

path is clear of all sticks, stones, wire

and other debris. Contact with such

debris may damage your machine.

• Keep your machine away from your feet

and other parts of your body when

switching on and during operation.

• Do not switch on your machine when it is

upside down.

• Walk, never run with the unit.

• Do not use your machine in the rain and

do not allow it to get wet.

• Use your machine only in daylight or

good artificial light.

• Do not cross gravel paths or roads whilst

the cutting line is rotating.

• Do not cut excessively steep slopes.

Be sure of your footing and cut across

the face of slopes, never up and down.

• Never use your machine with a

damaged guard (10) or without the guard

fixed in position.

• Be careful when trimming as freshly cut

grass is damp and slippery.

Safety of others

• Remember that the operator/user is

responsible for accidents or hazards

occuring to other people or their property.

• Never allow children or persons who are

unfamiliar with this type of machine to

use it, nor anyone who has not read

this leaflet.

• Do not allow children, animals or other

adults near your machine when in use -

always keep them well away from the

cutting area.

Care of your machine

• Store your machine in a dry place when

not in use, out of the reach of children.

• Do not use solvents or cleaning fluids

to clean your machine - use a blunt

scraper to remove grass and dirt. Always

disconnect from the electrical supply and

ensure the cutting line (9) is stationary

before cleaning.

• Do not operate your machine if any parts

are defective.

• Do not attempt to remove any parts

other than those mentioned in these

instructions.

• Use only Black & Decker recommended

replacement parts and accessories.

Electrical safety

Your machine should always be switched off

at the mains before disconnecting any plug

and socket connector, extension cables,

or cordsets.

Mains plug replacement - UK only

Should your mains plug need replacing and

you are competent to do this, proceed as

instructed below. If you are in doubt contact

a Black & Decker service centre or a

qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely,

a plug with bared copper conductors

is dangerous if engaged in a live

socket outlet.

360˚

6m/20ft

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Never use a

light socket

• Only fit 13 amp BS1363A approved

plugs fitted with the correctly rated fuse.

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug (see

below). Brown is for 'Live' (L) and blue is

for 'Neutral' (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath of the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

• Warning! Never connect Live or Neutral

wires to Earth pin marked E or .

Fuse replacement - UK only

Your machine is supplied with cable fitted

with a non-wireable plug.

• The plug is fitted with a 5 amp fuse

which is the recommended fuse for

your machine.

• Only use replacement fuses which are

approved to BS1362.

• When changing the fuse in your plug,

always ensure the fuse cover is refitted.

If the fuse cover is missing or damaged

do not use the plug.

Note: Fuses do not give personal protection

against electric shock.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA) circuit breaker in the house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to the machine be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

the machine from the safety instructions and

safe working practices given in this manual.

Extension cables or cordsets

You can use up to 30 metres (100ft) of

extension cord without undue loss of power.

Extension cords and cordsets should comply with

national regulations.

Preparing the trimmer for use

(Fig. 2)

2 • Take the trimmer and the guard (10) out

of the box.

• Remove the guard screw (12) which is

located on the underside of the guard

(Fig. 2.1).

• Place the guard into the channel on the

trimmer body (Fig. 2.2).

• Push the guard fully home until the guard

is flush with the body (Fig. 2.3).

• Replace the guard screw (Fig. 2.4).

• If correctly assembled, the guard will now

be secured to your trimmer.

• In transit, the end of the cutting line (9)

is taped to the side of the spool cover.

Please discard the tape to release the

length of line. There should be a

minimum of 9cm (3.5") of cutting line

protruding from the spool housing

before using your trimmer.

Note: When your machine is operated for

the first time any excess line will be cut off by

the line trimming blade (8) housed in the

guard. This is also the case for any

subsequent line adjustment. Because line

cut off by the blade in the guard may be

ejected, it is important that the amount of

excess line is kept to a minimum. Where an

excessive amount of line is pulled out, the

line should be cut back to the outside of the

guard before switching on your trimmer. Cut

the line off on the trimmer blade by hand.

• Always ensure that the spool cover is

secure before and after use.

How to use your trimmer (Fig. A - J)

In order to get the most from your trimmer please be

sure to follow the techniques shown. Do not be

impatient; you will obtain the best results through

experience and by following these simple rules.

Specyfikacje produktu

Marka:	Black & Decker
Kategoria:	Podcinacz
Model:	GL535

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Black & Decker GL535, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Podcinacz Black & Decker

Black & Decker GL570 Instrukcja

15 Października 2024

Black & Decker GL675 Instrukcja

17 Września 2024

Black & Decker STC1820D Instrukcja

16 Września 2024

Black & Decker STC1840EPCB Instrukcja

11 Września 2024

Black & Decker GSL360 Instrukcja

10 Września 2024

Black & Decker GL430S Instrukcja

3 Września 2024

Black & Decker GL300 Instrukcja

31 Sierpnia 2024

Black & Decker LST400 Instrukcja

31 Sierpnia 2024

Black & Decker GL225S Instrukcja

30 Sierpnia 2024

Black & Decker GL315 Instrukcja

28 Sierpnia 2024

Instrukcje Podcinacz

Najnowsze instrukcje dla Podcinacz

Husqvarna 236R Instrukcja

14 Października 2024

RYOBI One+ P20220 Instrukcja

9 Października 2024

Husqvarna 110iL Instrukcja

9 Października 2024

Toro 51434 Instrukcja

8 Października 2024

Toro 51490 Instrukcja

8 Października 2024

Toro 51494 Instrukcja

8 Października 2024

Toro 51498T Instrukcja

8 Października 2024

Toro 51653 Instrukcja

8 Października 2024

Toro i51020 Instrukcja

8 Października 2024

Toro 51480A Instrukcja

8 Października 2024