Instrukcja obsługi Black & Decker BEH200
Black & Decker
Hamer
BEH200
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker BEH200 (60 stron) w kategorii Hamer. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/60
www.blackanddecker.eu
1
2
3
45
6
BEH200
2
4
A
3
C
Intended use
Your BLACK+DECKER BEH200 Impact drill has been
designed for drilling in wood, metal, plastics, and masonry
as well as for screwdriving purposes. This tool is intended for
consumer use only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
suchasinthepresenceofammableliquids,gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric shock.
5
D
B
3
ENGLISH
(Original instructions)
3
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
powertoolwhileyouaretiredorundertheinuence
of drugs, alcohol or medication. A moment of inatten
tion while operating power tools may result in serious
personal injury.
b. Usepersonalprotectiveequipment.Alwaysweareye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazard
ous situation.
5. Service
a. Haveyourpowertoolservicedbyaqualiedrepair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for drills
and impact drills.
uWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uNever use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
Specyfikacje produktu
| Marka: | Black & Decker |
| Kategoria: | Hamer |
| Model: | BEH200 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Black & Decker BEH200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Hamer Black & Decker
4 Października 2024
27 Września 2024
16 Września 2024
12 Września 2024
9 Września 2024
6 Września 2024
5 Września 2024
4 Września 2024
26 Sierpnia 2024
24 Sierpnia 2024
Instrukcje Hamer
- Hamer AEG
- Hamer Milwaukee
- Hamer Bosch
- Hamer Global
- Hamer Bavaria By Einhell
- Hamer Scheppach
- Hamer Taurus
- Hamer DeWalt
- Hamer Einhell
- Hamer Makita
- Hamer Ozito
- Hamer RYOBI
- Hamer CMI
- Hamer Hilti
- Hamer Trotec
- Hamer Güde
- Hamer Bavaria
- Hamer McKenzie
- Hamer Ergotools Pattfield
- Hamer Ferm
- Hamer Hitachi
- Hamer Craftsman
- Hamer Fieldmann
- Hamer PowerPlus
- Hamer Alpha Tools
- Hamer XU1
- Hamer HiKOKI
- Hamer Porter-Cable
- Hamer Metabo
- Hamer Power Craft
- Hamer Topcraft
- Hamer Anova
- Hamer King Craft
- Hamer Full Boar
- Hamer Toolson
- Hamer Robust
- Hamer Einhell Bavaria
- Hamer MyTool
- Hamer Prowork
Najnowsze instrukcje dla Hamer
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
6 Października 2024