Instrukcja obsługi Black & Decker 2912
Black & Decker
Flesz
2912
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker 2912 (2 stron) w kategorii Flesz. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
If you have any questions, call 1-800-9-BD TOOL (1-800-923-8665)
9.6, 12, 14.4 Volt Cordless Worklights
2909, 2912, 2914
Please take time to read this manual and pay particular attention to the safety
rules we’ve provided for your protection. If you have any questions about
your tool please call:
1-800-9-BD TOOL
(1-800-923-8665)
NOTE: Your 2909 worklight operates on a 9.6V power pack (97046 or
97148) Your 2912 worklight operates on a 12V power pack (97150 or
97051). Your 2914 worklight operates on a 14.4V power pack (97152).
Power packs are sold separately.
WARNING: When using electric tools, basic safety precautions should
always be followed to reduce risk of fire, electric shock, and personal
injury, including the following:
READ ALL INSTRUCTIONS
Safety Rules for Worklights
1. WARNING: DO NOT OPERATE FLASHLIGHT OR CHARGER NEAR
FLAMMABLE LIQUIDS OR IN GASEOUS OR EXPLOSIVE
ATMOSPHERES. INTERNAL SPARKS MAY IGNITE FUMES.
2. WARNING: Lens and bulb become hot during use.
• During or immediately after use, don’t lay worklight flat on lens
surface.
• Don’t touch lens surface when bulb is lit.
• Handle worklight with care around any flammable surface.
• If bulb has been lit, let worklight cool for several minutes before
changing bulb.
Safety Rules for Chargers
1. Before using charger, read all instructions and cautionary markings
on (1) charger, (2) battery pack, and (3) product using battery pack.
2. DANGER: 120 volts present at charging terminals. Do not probe with
conductive objects. Danger of electric shock or electrocution.
3. If battery pack case is cracked or damaged, do not insert into charger.
Danger of electric shock or electrocution.
4. The charger and battery pack are specifically designed to work
together. DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual.
5. Do not expose charger to rain or snow.
6. To reduce risk of damage to electric plug and cord, pull by plug rather
than cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped
over, or otherwise subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary.
Use of improper extension cord could result in risk of fire, electric
shock, or electrocution.
9. Two wire cords can be used with 2 or 3 wire extension cords. Only
round jacketed extension cords should be used, and we recommend
that they be listed by Underwriters Laboratories (U.L.) (C.S.A. in
Canada.) The letters WA on the cord jacket indicate that the cord is
suitable for outdoor use.
10.An extension cord must have adequate wire size (AWG or American
Wire Gauge) for safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the
total length, be sure each individual extension contains at least the
minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS
NAMEPLATE RATING AMPS - 0 - 10.0
Total Extension Cord Length (feet) 25 50 75 100 125 150 175
Wire Gauge 18 18 16 16 14 14 12
11.The charger is ventilated through slots in the top and the bottom of
the housing. Do not place any object on top of the charger or place
the charger on a soft surface that might block the ventilation slots
and result in excessive internal heat. Place the charger in a position
away from any heat source.
12.Do not operate charger with damaged cord or plug — have them
replaced immediately.
13.Do not operate charger if it has received a sharp blow, been dropped,
or otherwise damaged in any way; take it to an authorized B&D
service center.
14.Do not disassemble charger; take it to an authorized B&D service
center when service or repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or fire.
15.To reduce risk of electric shock, unplug charger from outlet before
attempting any cleaning. Removing the battery pack will not reduce
this risk.
16.NEVER attempt to connect 2 chargers together.
17.DO NOT store or use the tool and battery pack in locations where the
temperature may reach or exceed 105°F (such as outside sheds or
metal buildings in summer).
18.The charger is designed to operate on standard household electrical
power (120 volts). Do not attempt to use it on any other voltage!
Safety Rules for Batteries
1. Do not incinerate the battery pack even if it is severely damaged or is
completely worn out.The battery pack can explode in a fire.
2. A small leakage of liquid from the battery pack cells may occur under
extreme usage or temperature conditions. This does not indicate a
failure. However, if the outer seal is broken and this leakage gets on
your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets into your eyes, flush them with clean water for
a minimum of 10 minutes and seek immediate medical attention.
(Medical note: The liquid is 25-35% solution of potassium
hydroxide.)
3. Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, immediately discontinue
use and do not recharge.
4. Do not carry extra battery packs in aprons, pockets, or tool boxes
along with other metal objects. Battery pack could be short circuited
causing damage to the battery pack and possibly causing severe burn
or fire.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Charging Procedure
98014/97014 (1 Hour Chargers) only
1. Plug the charger into an appropriate AC power outlet.
2. Insert the battery pack into the charger, as shown in Figure 1, making
sure the pack is fully seated in the charger. The red (charging) light
will blink continuously indicating that the charging process has
started.
3. The battery pack will be fully charged in about 1 hour under most
conditions. The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and may be
used at this time or left in the charger.
If you have any questions, call 1-800-9-BD TOOL (1-800-923-8665)
98020 (15 Minute Charger) only
1. Plug the charger into an appropriate AC power outlet. The charger will
beep twice and the red light will blink and then go off.
2. Insert the battery pack into the charger, as shown in Figure 1, making
sure the pack is fully seated in the charger. The red light will blink and
the charger will beep once indicating the charging process has started.
3. The battery pack will be fully charged in less than 15 minutes under
most conditions. This will be indicated by the red light remaining ON
and 3 audible beeps. The pack is fully charged and may be used at this
time or left in the charger.
Power Pack Insertion and Removal
To insert the power pack into your worklight, slide it into the end of the
light until it snaps into place. To remove the power pack, depress the
release buttons shown and withdraw the power pack.
Switch
To turn the light on, slide the switch forward. To turn it off, slide the switch
back.
Swiveling Head (Figure 2)
Your worklight has a swiveling head. To convert your light to a right angle
model, grasp the front end of the light forward of the switch and hold the
back end firmly. Twist the front end clockwise (as viewed from the lens)
until the head swivels 90 degrees and clicks into place. To return the head
to a straight position, rotate the head (as viewed from the lens)
counterclockwise until it clicks into the straight position.
Replacing the Light Bulb
Worklight Cat. No Replacement Bulb Cat. No.
2909 29090
2912 29120
2914 29140
To replace the light bulb, first unscrew the lens holder. Pull the bulb out of
the spring, and insert a new bulb. Reinstall lens holder.
NOTE:Do not look directly into the worklight beam.
Spare Bulb Storage (Figure 3)
To store a bulb, unscrew the lens holder and remove it. Inside the body of
the worklight is the storage socket. To remove the bulb, pull it up and out
of the storage area. a pack from the charger andNOTE: Removing
immediately inserting it into the worklight may weaken bulb life.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
nickel-cadmium battery indicates that the costs to recycle the battery at
the end of its useful life have already been paid by B&D. In some areas, it
is illegal to place spent nickel-cadmium batteries in the trash or municipal
solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC in cooperation with B&D and other battery users, has established
programs in the United States to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural
resources by returning the spent nickel-cadmium battery to an authorized
service center or to your local retailer for recycling. You may also contact
your local recycling center for information on where to drop off the spent
battery.
One Year Free MaIntenance
All B&D tools for Industry and Construction are covered under a one year
free maintenance program where B&D will inspect your tool for safety and
provide necessary maintenance or repairs, including normal wear and tear
parts, for one year, FREE OF CHARGE.
Full Warranty
All B&D tools for Industry and Construction are warranted to be free of
any defects in materials or workmanship. Upon thorough examination of
tool, B&D will repair or replace, at our option, any product that is
determined to be defective.
Conditions
The service/safety check and the warranty do not apply to: repairs made or
attempted by anyone other than an authorized B&D service location;
misuse, abuse, neglect, improper application of the tool; missing parts; or
normal wear and tear (after first year of ownership). Please return the
complete unit, transportation prepaid, to any B&D factory owned or B&D
authorized service center location (list provided with tool or see Yellow
Pages under “Tools Electric”).
Fig. 1
Fig. 2
Fig. 3
LENS HOLDER
BULB
BATTERY RELEASE BUTTON
SPARE BULB STORAGE
POWER PACK (NOT INCLUDED)
SWIVELING HEAD
SWITCH
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A. F#154530
(OCT96-2)
Printed in Taiwan
Copyright © 1996 Black & Decker
Specyfikacje produktu
| Marka: | Black & Decker |
| Kategoria: | Flesz |
| Model: | 2912 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Black & Decker 2912, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Flesz Black & Decker
15 Września 2024
21 Sierpnia 2024
15 Sierpnia 2024
9 Sierpnia 2024
6 Lipca 2024
6 Lipca 2024
4 Lipca 2024
Instrukcje Flesz
- Flesz Beko
- Flesz Gorenje
- Flesz Milwaukee
- Flesz Philips
- Flesz SilverCrest
- Flesz Toolcraft
- Flesz Nedis
- Flesz Stanley
- Flesz Fenix
- Flesz Garmin
- Flesz DeWalt
- Flesz Einhell
- Flesz Silverline
- Flesz Makita
- Flesz ArmyTek
- Flesz Petzl
- Flesz Knog
- Flesz Cateye
- Flesz Ledlenser
- Flesz Emos
- Flesz NightStick
- Flesz Ansmann
- Flesz Little Tikes
- Flesz Velleman
- Flesz VDO
- Flesz IVT
- Flesz Maverick
- Flesz Rocktrail
- Flesz Maglite
- Flesz Aluratek
- Flesz Abus
- Flesz Olympia
- Flesz Hama
- Flesz Alpen Optics
- Flesz Princeton Tec
- Flesz Duronic
- Flesz Goobay
- Flesz Trelock
- Flesz Anker
- Flesz Nitecore
- Flesz Craftsman
- Flesz Olight
- Flesz Klein Tools
- Flesz Black Diamond
- Flesz PowerPlus
- Flesz Asaklitt
- Flesz Powerfix
- Flesz HiKOKI
- Flesz Dörr
- Flesz WAGAN
- Flesz SureFire
- Flesz AccuLux
- Flesz Varta
- Flesz Spanninga
- Flesz Brennenstuhl
- Flesz Streamlight
- Flesz Nordride
- Flesz Silva
- Flesz Trebs
- Flesz Maktec
- Flesz Steren
- Flesz Livarno
- Flesz Kayoba
- Flesz Barska
- Flesz LED Lenser
- Flesz Greenlee
- Flesz HQ
- Flesz Parat
- Flesz Coleman
- Flesz Energizer
- Flesz Silva Schneider
- Flesz Tecxus
- Flesz Goal Zero
- Flesz Beghelli
- Flesz 4K5
- Flesz GP
- Flesz CEL-TEC
- Flesz Nebo
- Flesz Underwater Kinetics
- Flesz MOON
- Flesz KSE-Lights
- Flesz SuperNova
- Flesz Coast
Najnowsze instrukcje dla Flesz
15 Października 2024
11 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024