Instrukcja obsługi Black & Decker 11650
Black & Decker
szlifierka
11650
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker 11650 (20 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/20
Form No. 587857-00 MAR-04 Printed in China
Instruction Manual
WARNING:
Before using this product,
read this manual and follow
all its Safety Rules and
Operating Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
www.sears.com/craftsman
• Safety
• Operation
• Maintenance
• Parts List
• Español
4 INCH
ANGLE GRINDER
Model 900.116500
587857-00 900.116500 sears 3/23/04 7:21 AM Page 1
WARNING! Read and understand all
instructions. Failure to follow all instructions
listed below may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit.
Cluttered benches and dark areas invite
accidents.
•Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gases,
or dust. Power tools create sparks which
may ignite the dust or fumes.
•Keep bystanders, children, and visitors
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
• Double insulated tools are equipped
with a polarized plug (one blade is
wider than the other.) This plug will fit
in a polarized outlet only one way. If
the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install
a polarized outlet. Do not change the
plug in any way. Double Insulation
eliminates the need for the three wire
grounded power cord and grounded
power supply system. Applicable only to
Class ll tools.
•Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your
body is grounded.
•Don’t expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
•Do not abuse the cord. Never use the
cord to carry the tools or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace damaged cords immediately.
Damaged cords increase the risk of
electric shock.
2
FULL ONE YEAR WARRANTY ON CRAFTSMAN ANGLE GRINDER
If this Craftsman angle grinder fails due to a defect in material or workmanship within
one year from the date of purchase, Sears will replace it, free of charge.
If this Craftsman angle grinder is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
WARRANTY SERVICE
To obtain replacement under this warranty, return the grinder to your nearest Sears
store in the United States.
This warranty applies only while this angle grinder is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCK AND CO., DEPT. 817 WA, HOFFMAN ESTATES, IL 60179
SEARS WARRANTY
GENERAL SAFETY RULES
ANGLE GRINDER DIAGRAM
On / Off Switch (1)
Wheel Guard (6)
Spindle Lock Button (3)
Depressed Center Wheel (4)
1
Auxiliary Side Handle (5) Lock-On Button (2)
587857-00 900.116500 sears 3/23/04 7:21 AM Page 2
3
• When operating a power tool outside,
use an outdoor extension cord marked
“W-A” or “W.” These cords are rated for
outdoor use and reduce the risk of electric
shock.
Personal Safety
• Stay alert, watch what you are doing
and use common sense when
operating a power tool. Do not use tool
while tired or under the influence of
drugs, alcohol, or medication. A
moment of inattention while operating
power tools may result in serious
personal injury,
• Dress properly. Do not wear loose
clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewelry, or long hair can be caught in
moving parts.
• Avoid accidental starting. Be sure
switch is off before plugging in.
Carrying tools with your finger on the
switch or plugging in tools that have the
switch on invites accidents.
• Remove adjusting keys or wrenches
before turning the tool on. A wrench or
a key that is left attached to a rotating part
of the tool may result in personal injury.
• Do not overreach. Keep proper footing
and balance at all times. Proper footing
and balance enables better control of the
tool in unexpected situations.
• Use safety equipment. Always wear
eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing
protection must be used for appropriate
conditions.
Tool Use and Care
• Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by
hand or against your body is unstable and
may lead to loss of control.
• Do not force tool. Use the correct tool
for your application. The correct tool will
do the job better and safer at the rate for
which it is designed.
• Do not use tool if switch does not turn
it on or off. Any tool that cannot be
controlled with the switch is dangerous
and must be repaired.
• Disconnect the plug from the power
source before making any
adjustments, changing accessories, or
storing the tool. Such preventive safety
measures reduce the risk of starting the
tool accidentally.
• Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained
users.
• Maintain tools with care. Keep cutting
tools sharp and clean. Properly
maintained tools, with sharp cutting
edges are less likely to bind and are
easier to control.
• Check for misalignment or binding of
moving parts, breakage of parts, and
any other condition that may affect the
tools operation. If damaged, have the
tool serviced before using. Many
accidents are caused by poorly
maintained tools.
• Use only accessories that are
recommended by the manufacturer for
your model. Accessories that may be
suitable for one tool, may become
hazardous when used on another tool.
Service
• Tool service must be performed only
by qualified repair personnel. Service
or maintenance performed by unqualified
personnel could result in a risk of injury.
• When servicing a tool, use only
identical replacement parts. Follow
instructions in the Maintenance
section of this manual. Use of
unauthorized parts or failure to follow
Maintenance Instructions may create a
risk of electric shock or injury.
SPECIFIC SAFETY RULES
• Always use proper guard with
grinding wheel. A guard protects
operator from broken wheel fragments.
Always position the guard so that as
much of the exposed disc as possible
is pointing away from you.
• Accessories must be rated for at
least the speed recommended on the
tool warning label. Wheels and other
accessories running over rated speed
can fly apart and cause injury.
• Hold tool by insulated gripping
surfaces when performing an
operation where the cutting tool may
contact hidden wiring or its own
cord. Contact with a "live" wire will make
exposed metal parts of the tool "live"
and shock the operator.
587857-00 900.116500 sears 3/23/04 7:21 AM Page 3
Specyfikacje produktu
| Marka: | Black & Decker |
| Kategoria: | szlifierka |
| Model: | 11650 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Black & Decker 11650, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje szlifierka Black & Decker
8 Października 2024
29 Września 2024
23 Września 2024
19 Września 2024
13 Września 2024
12 Września 2024
5 Września 2024
27 Sierpnia 2024
25 Sierpnia 2024
24 Sierpnia 2024
Instrukcje szlifierka
- szlifierka AEG
- szlifierka Worx
- szlifierka Kawasaki
- szlifierka Milwaukee
- szlifierka Bosch
- szlifierka Yato
- szlifierka Parkside
- szlifierka Global
- szlifierka Toolcraft
- szlifierka Festool
- szlifierka Bavaria By Einhell
- szlifierka SW-Stahl
- szlifierka Stanley
- szlifierka Mirka
- szlifierka Scheppach
- szlifierka Proxxon
- szlifierka Adler
- szlifierka Hazet
- szlifierka RIKON
- szlifierka DeWalt
- szlifierka Einhell
- szlifierka Silverline
- szlifierka ECG
- szlifierka Makita
- szlifierka Ozito
- szlifierka RYOBI
- szlifierka Chicago Pneumatic
- szlifierka Flex
- szlifierka GO/ON
- szlifierka DEDRA
- szlifierka Hilti
- szlifierka Rodcraft
- szlifierka Dremel
- szlifierka Handwerk
- szlifierka Meec Tools
- szlifierka Güde
- szlifierka Bavaria
- szlifierka Solo
- szlifierka DURO PRO
- szlifierka McKenzie
- szlifierka Westfalia
- szlifierka Fein
- szlifierka Ferm
- szlifierka Hitachi
- szlifierka Craftsman
- szlifierka Fieldmann
- szlifierka Ridgid
- szlifierka PowerPlus
- szlifierka Alpha Tools
- szlifierka Vonroc
- szlifierka Powerfix
- szlifierka HiKOKI
- szlifierka Workzone
- szlifierka Proviel
- szlifierka Porter-Cable
- szlifierka Metabo
- szlifierka Skil
- szlifierka ABB
- szlifierka Aquapur
- szlifierka Toolland
- szlifierka Profitec
- szlifierka United Office
- szlifierka Maktec
- szlifierka Steren
- szlifierka Bort
- szlifierka Tanaka
- szlifierka Yamato
- szlifierka Malmbergs
- szlifierka Power Craft
- szlifierka Bunn
- szlifierka Eibenstock
- szlifierka Gamma
- szlifierka Kress
- szlifierka Dolmar
- szlifierka Duro
- szlifierka Pattfield
- szlifierka Defort
- szlifierka Max
- szlifierka Truper
- szlifierka Bruder Mannesmann
- szlifierka Meister Craft
- szlifierka Batavia
- szlifierka Holzmann
- szlifierka Graphite
- szlifierka Stomer
- szlifierka Dolmar(Makita)
- szlifierka Sthor
- szlifierka Ergofix
- szlifierka Neo
- szlifierka Victoria Arduino
- szlifierka Felisatti
- szlifierka ATI-ZDL
- szlifierka Gude Pro
- szlifierka Einhell Bavaria
- szlifierka Gladiator
Najnowsze instrukcje dla szlifierka
15 Października 2024
14 Października 2024
14 Października 2024
12 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024