Instrukcja obsługi Biostar TP43D2-A7


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Biostar TP43D2-A7 (61 stron) w kategorii płyta główna. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/61
TP45D2-A7/TP43D2-A7 Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ............................................................ 1
1.1 Before You Start......................................................................................... 1
1.2 Package Checklist ..................................................................................... 1
1.3 Motherboard Features.............................................................................. 2
1.4 Rear Panel Connectors.............................................................................. 3
1.5 Motherboard Layout................................................................................. 4
Chapter 2: Hardware Installation ............................................. 5
2.1 Installing Central Processing Unit (CPU) ............................................... 5
2.2 FAN Headers .............................................................................................. 7
2.3 Installing System Memory ........................................................................ 8
2.4 Connectors and Slots................................................................................ 10
Chapter 3: Headers & Jumpers Setup ..................................... 12
3.1 How to Setup Jumpers............................................................................. 12
3.2 Detail Settings .......................................................................................... 12
Chapter 4: T-Series BIOS & Software ..................................... 20
4.1 T-Series BIOS............................................................................................. 20
4.2 T-Series Software...................................................................................... 28
Chapter 5: Useful Help ............................................................ 37
5.1 Driver Installation Note.......................................................................... 37
5.2 Extra Information.................................................................................... 38
5.3 AMI BIOS Beep Code ............................................................................... 39
5.4 Troubleshooting ....................................................................................... 40
Appendencies: SPEC In Other Language ................................ 42
German.................................................................................................................. 42
France .................................................................................................................... 44
Italian..................................................................................................................... 46
Spanish................................................................................................................... 48
Portuguese ............................................................................................................ 50
Polish...................................................................................................................... 52
Russian ................................................................................................................... 54
Arabic..................................................................................................................... 56
Japanese ................................................................................................................ 58
TP45D2-A7/TP43D2-A7
1
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
1.2 P CACKAGE HECKLIST
HDD Cable X 1
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
Users Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)
Note: The package contents may differ by area or your motherboard version.
Motherboard Manual
2
1.3 MOTHERBOARD FEATURES
TP45D2-A7 TP43D2-A7
CPU
LGA 775
Intel Core2Duo / Core2Quad /
Pentium Dual-Core / Celeron Dual-Core /
Celeron 4xx processor
Supports Execute Disable Bit / Enhanced Intel
SpeedSte / Intel Architecture-64 / Extended
Memory 64 Technology / Virtualization
Technology
LGA 775
Intel Core2Duo / Core2Quad /
Pentium Dual-Core / Celeron Dual-Core /
Celeron 4xx processor
Supports Execute Disable Bit / Enhanced Intel
SpeedSte / Intel Architecture-64 / Extended
Memory 64 Technology / Virtualization
Technology
FSB Support 800 / 1066 / 1333 / 1600 MHz Support 800 / 1066 / 1333 / 1600 MHz
Chipset Intel P45
Intel ICH10
Intel P43
Intel ICH10
Super I/O
ITE 8718F
Provides the most commonly used legacy Super
I/O functionality.
Low Pin Count Interface
Environment Control initiatives,
Hardware Monitor Controller
Fan Speed Controller
ITE's "Smart Guardian" function
ITE 8718F
Provides the most commonly used legacy Super
I/O functionality.
Low Pin Count Interface
Environment Control initiatives,
Hardware Monitor Controller
Fan Speed Controller
ITE's "Smart Guardian" function
Main
Memory
DIMM Slots x 4
Each DIMM supports 256MB / 512MB / 1GB /
2GB DDR2
Max Memory Capicity 8GB
Dual Channel Mode DDR2 memory module
Supports DDR2 1066 / 800 / 667
Registered DIMM and ECC DIMM is not
supported
DIMM Slots x 4
Each DIMM supports 256MB / 512MB / 1GB /
2GB DDR2
Max Memory Capicity 8GB
Dual Channel Mode DDR2 memory module
Supports DDR2 1066 / 800 / 667
Registered DIMM and ECC DIMM is not
supported
IDE
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4
JMicro JMB368
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4
SATA 2
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant
LAN
Realtek RTL 8111C
10 / 100 Mb/s / 1Gb/s auto negotiation
Half / Full duplex capability
Realtek RTL 8111C
10 / 100 Mb/s / 1Gb/s auto negotiation
Half / Full duplex capability
Sound
Codec
ALC662
5.1 channels audio out
High Definition Audio
ALC662
5.1 channels audio out
High Definition Audio
TP45D2-A7/TP43D2-A7
5
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING NIT CENTRAL PROCESSING U (CPU)
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
TP45D2-A7/TP43D2-A7
7
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
Pin
Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
1
4
4 Smart Fan
Control
JSFAN1/JSFAN2: System Fan Headers
Pin
Assignment
1 Ground
2 +12V
1
3
JSFAN1
JSFAN2
3 FAN RPM rate
sense
Note:
The JSFAN1/JSFAN2 support 3-pin head connectors, and the JCFAN1 supports 4-pin
head connector. When connecting with wires onto connectors, please note that the red
wire is the positive and should be connected to pin#2, and the black wire is Ground and
should be connected to GND.
Motherboard Manual
8
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
DDR2_A1
DDR2_B1
DDR2_A2
DDR2_B2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
TP45D2-A7/TP43D2-A7
9
B. Memory Capacity
DIMM Socket
Location DDR2 Module Total Memory
Size
DDR2_A1 256MB/512MB/1GB/2GB
DDR2_A2 256MB/512MB/1GB/2GB
DDR2_B1 256MB/512MB/1GB/2GB
DDR2_B2 256MB/512MB/1GB/2GB
Max is 8GB.
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DDR2_A1 DDR2_A2 DDR2_B1 DDR2_B2
Enabled O X O X
Enabled X O X O
Enabled O O O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
Motherboard Manual
10
2.4 C S ONNECTORS AND LOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
34
331
2
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
1
2 40
39
TP45D2-A7/TP43D2-A7
11
PEX16_1: PCI-Express Gen2 x16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
- 2X bandwidth over the PCI-Express 1.1 architecture.
PEX1_1/PEX1_2: PCI-Express p13-x1 Slots
- PCI-Express 1.1 compliant.
- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
- 2X bandwidth over the PCI architecture.
PEX16_1
PEX1_2
PEX1_1
PCI1~PCI3: Peripheral Component Interconnect Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI2
PCI1
PCI3
Motherboard Manual
12
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open.
Pin opened Pin closed Pin1-2 closed
3.2 DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
1
9
8
16
PWR_LED
On/Off
RST
HLED
SPK
+ +
+
-
-
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A
2 N/A 10 N/A N/A
3 N/A 11 N/A N/A
4 Speaker
Speaker
Connector
12 Power LED (+)
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
Hard drive
LED 14 Power LED (-)
Power LED
7 Ground 15 Power button
8 Reset control Reset button 16 Ground Power-on button
TP45D2-A7/TP43D2-A7
13
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
1
12
13
24
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
Pin
Assignment
1 +12V
2 +12V
3 Ground
1
2 3
4
4 Ground
Note:
Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.
Motherboard Manual
14
J1: Auxiliary Power for Graphics
This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.
Pin
Assignment
1 +12V
2 Ground
3 Ground
4 VCC
1
4
SATA1~SATA6: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
Pin
Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
1 4 7
SATA1
SATA2
SATA3
SATA4
SATA5
SATA6
7 Ground
TP45D2-A7/TP43D2-A7
15
JUSB3/JUSB4/JUSB5: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 Key
1
2
9
10
JUSB4
JUSB5JUSB3
10 NC
JAUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
Pin
Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
1 2
9 10
10 Jack Sense
Motherboard Manual
16
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..
Pin
Assig nment
1 Left Channel Input
2 Ground
3 Ground
1
4
4 Right Channel Input
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
3
1
3
Pin 2-3 Close:
Clear CMOS data.
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper toPin 2-3 close.
3. Wait for five seconds.
4. Set the jumper toPin 1-2 close.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
TP45D2-A7/TP43D2-A7
17
On-Board LED Indicators
There are 2 LED indicators on the motherboard to show system status.
LED_D1
LED_D2
LED_D1 and LED_D2:
These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:
LED_D1 LED_D2 Message
ON ON Normal
ON OFF Memory Error
OFF ON VGA Error
OFF OFF Abnormal: CPU / Chipset error.
On-Board Buttons
There are 2 on-board buttons.
RSTSW2
PWRSW1
PWRSW1:
This is an on-board Power Switch button.
RSTSW2:
This is an on-board Reset button.
Motherboard Manual
18
JPRNT1: Printer Port Connector
This header allows you to connect printer on the PC.
1
2
25
Pin Assignment Pin Assignment
1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key
JCOM1: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
Pin
Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key
1
2
9
10
TP45D2-A7/TP43D2-A7
19
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSB1/JUSB2/JRJ45USB1.
JUSBV2: +5V for USB ports at JUSB3/JUSB4/JUSB5.
Pin 2-3 Close:
JUSBV1: +5V STB for USB ports at JUSB1/JUSB2/ JRJ45USB1.
JUSBV2: +5V STB for USB ports at JUSB3/JUSB4/JUSB5.
1
3
Pin 1-2 close
1 3
1
3
JUSBV1
JUSBV2
1
3
Pin 2-3 close
JKBV1: Power Source Header for PS/2 Keyboard and Mouse
1
3
Pin 1-2 close
+5V for PS/2 keyboard and
mouse.
1
3
1
3
Pin 2-3 close
+5V STB for PS/2 keyboard
and mouse.
Motherboard Manual
20
CHAPTER 4: T-SERIES BIOS & SOFTWARE
4.1 T-SERIES BIOS
T-Series BIOS Features
Overclocking Navigator Engine (O.N.E.)
Memory Integration Test (M.I.T., under Overclock Navigator Engine)
BIO-Flasher: Update BIOS file from USB Flash Drive or FDD
Self Recovery System (S.R.S)
Smart Fan Function
CMOS Reloading Program
A. Overclocking Navigator Engine (O.N.E.)
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Normal]
Memory Test [Disabled]
Auto OverClock System [V6-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
Normal
Automate OverClock
Manual OverClock
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setu
p
CD.
TP45D2-A7/TP43D2-A7
21
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Normal]
Memory Test [Disabled]
Auto OverClock System [V6-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
Normal
Automate OverClock
Manual OverClock
Options
Normal
Automate OverClock
Manual OverClock
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Manual OverClock]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Memory Test [Disabled]
Auto OverClock System [V6-Tech Engine]
Exit
Options
Normal
Automate OverClock
Manual OverClock
Intel(R) SpeedStep(tm) Tech
This item allows you to enable SpeedStep technology for better power
saving. SpeedStep is a technology built into some Intel processors that
allows the clock speed of the processor to be dynamically changed by
software.
Ratio CMOS Setting
This item allows you to set the CPU ratio frequency.
CPU Frequency Setting
CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.
Motherboard Manual
22
Over Clock Retry Count
This item allows you to set the overclock fail retry times.
FSB(Bsel) To NorthBridge Latch
This item allows you to select the FSB Frequency.
DRAM Frequency
To get better system performance, sometimes downgrading the memory
frequency is necessary when CPU frequency is adjusted over the upper
limit.
DDR2 Enhanced Mode
This item allows you to control the DDR2 ram enhanced mode.
DRAM Timing Configuration
Enter this item for more advanced DRAM timing settings.
Clock Gen Configuration
Enter this item for more advanced Clock Gen settings.
ALL Voltage Configuration
Enter this item for more advanced voltage settings.
Automatic Overclock System (A.O.S.)
For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single step.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Normal]
Memory Test [Disabled]
Auto OverClock System [V6-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
Normal
Automate OverClock
Manual OverClock
Options
Normal
Manual OverClock
Automate OverClock
NOTE
Overclock is an optional process, but not a “must-do” process; it is not
recommended for inexperienced users. Therefore, we will not be responsible
for any hardware damage which may be caused by overclocking. We also
would not
g
uarantee an
y
overclockin
g
p
erformance.
TP45D2-A7/TP43D2-A7
23
V6 Tech Engine
This engine will make a good over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Automate OverClock]
Memory Test [Disabled]
Auto OverClock System [V6-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
V6-Tech Engine
V8-Tech Engine
V12-Tech Engine
V8 Tech Engine
This engine will make a better over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Automate OverClock]
Memory Test [Disabled]
Auto OverClock System [V8-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
V6-Tech Engine
V8-Tech Engine
V12-Tech Engine
V12 Tech Engine
This engine will make a best over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset O.N.E
vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
Enter
F1
F10
ESC
Over-Clocking Navigator setting
WARNING: Setting wrong values in below sections
may cause system to malfunction.
=========== Automate OverClock System ===========
============ Manual OverClock System ============
Over-Clocking Navigator [Automate OverClock]
Memory Test [Disabled]
Auto OverClock System [V12-Tech Engine]
Intel(R) SpeedStep(tm) tech [Enabled]
Ratio CMOS Setting [ x10.0]
CPU Frequency Setting [266]
Over Clock Retry Count [3]
FSB(Bsel) To NorthBridge Latch [Auto]
DRAM Frequency [Auto]
DDR2 Enhanced Mode [Auto]
> DRAM Timing Configuration
> Clock Gen Configuration
> ALL Voltage Configuration
Exit
Options
V6-Tech Engine
V8-Tech Engine
V12-Tech Engine
TP45D2-A7/TP43D2-A7
25
C. BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIO-Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.
5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.
6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.
z This utility only allows storage device with FAT32/16 format and single
partition.
z Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
TP45D2-A7/TP43D2-A7
31
Over Voltage Panel
Manual Adjust
CPU/ Memo ry/Chipset/FSB Voltage
CPU Voltage
This function allows user to adjust CPU voltage. Click on+ to increase
or “-“ to decrease the CPU voltage.
Memory Voltage
This function allows user to adjust Memory voltage. Click on+ to
increase or -“ to decrease the Memory voltage.
Chip Voltage
This function allows user to adjust Chipset voltage. Click on +” to
increase or -“ to decrease the Chipset voltage.
FSB Voltage
This function allows user to adjust FSB voltage. Click on + to increase
or “-“ to decrease the FSB voltage.
Motherboard Manual
32
About Panel
In this panel, you can get model
name and other system information
that may related to over-clocking.
You can also get the version number
of this software.
Note
Because the Over Clock and Over
Voltage features are controlled by
several separate chipset, the utility
divides these features to separate
panels. If one chipset is not on
board, the correlative button in Main
panel will be disabled, but it will not
interfere with other panels’ functions.
This property can make the utility
more robust.
Hardware Monitor
HW Monitor is a monitor utility that helps you to maintain the health of the PC.
It provides real-time information of CPU/GPU/System temperature, fan speed,
and voltage.
This area shows CPU/System temperature
Voltage Panel Fan Panel
Tu rn to Fan Panel
This area shows voltage information
This area shows CPU informa tion
Turn to Vol tage Panel
This area shows CPU/System f an speed


Specyfikacje produktu

Marka: Biostar
Kategoria: płyta główna
Model: TP43D2-A7

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Biostar TP43D2-A7, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą