Instrukcja obsługi Bestway SaluSpa 60086

Bestway Niesklasyfikowane SaluSpa 60086

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bestway SaluSpa 60086 (112 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/112
OWNER’S MANUAL EN
VISIT WA YO LBEST Y UTUBE CHANNE
IMPORTANT SAFETY INSTRUCTIONS pg 003
PRE-SETUP CHECK LIST pg 007
INSTALLATION pg 015
SET-UP INSTRUCTION IN WINTER pg 015
USING THE SPA pg 019
MAINTENANCE pg 022
DISASSEMBLY AND STORAGE pg 024
TROUBLESHOOTING pg 026
ERROR CODES pg 027
FOR N VI OS INSTRUCTIO DE
PL VISIT:EASE
BEST YCWA ORP.C ORT OM/SUPP
CONTENTS
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
Fo Q, Manu , idr FA als V eos r O
spare arts ease P , Pl Visit
bestwaycorp.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL
INSTRUCTIONS.
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum 6 AWG (13.3 mm
2
)
solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
WARNING – This product is provided with a ground-fault circuit-interrupter integrated
with the power plug at the end of the cord. The GFCI must be tested before each
use. With the product operating, push the test button on the GFCI and the product
should not operate. Push the reset button on the GFCI and the product should now
operate normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electrical shock. Disconnect the power
until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the
specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible. Never operate spa if
the suction fittings are broken or missing. Never replace a suction fitting with one
rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal
surfaces. As an alternative, a spa may be installed within 5 feet of metal surfaces if
each metal surface is permanently connected by a minimum 6 AWG (13.3 mm
2
) solid
copper conductor to the wire connector on the terminal box that is provided for this
purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed 104°F (40°C). Water temperatures
between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when spa
use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to100°F (38°C).
c) Before entering a spa, the user should measure the water temperature with an
accurate thermometer since the tolerance of water temperature-regulating devices
3
varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f) Persons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect heart
rate, blood pressure, and circulation.
WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS
RAINING.
WARNING: Water attracts children; Always attach a spa cover after each use.
WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than
104°F (40°C) into the Spa.
CONSULT YOUR PHYSICIAN FOR
RECOMMENDATIONS.
CAUTION:
We strongly recommend not to unfold and inflate the spa if the ambient temperature
is below 59°F(15°C). We suggest inflating the spa indoors, and then continuing set
up outdoors. If the outdoor temperature is lower than 42.8°F(6°C), the spa heater
must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 42.8°F(6°C) and 50°F(10°C) to prevent damage, such as water
freezing in the pipes or the circulation system.
IMPORTANT:
If the Freeze Shield™ system isn’t working, alarms will pop up on the
spa. Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(6°C). In case of a long-term absence from home when there is a risk of
temperatures falling below 42.8°F(6°C), we strongly suggest disassembling the spa
and storing it following the storage procedure.
CAUTION: Do not use the spa alone.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are
slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless
the spa is filled with water.
CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.
NOTE: Please examine equipment before use. Notify Bestway
®
at the customer
service address listed on this manual for any damaged or missing parts at the time of
purchase. Verify that the equipment components represent the model that you had
intended to purchase.
SAVE THESE INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT
ADULT SUPERVISION.
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS
ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR
HOT TUB.
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA
OR HOT TUB.
WARNING: TO AVOID INJURY, EXERCISE CARE WHEN ENTERING OR EXITING
THE SPA OR HOT TUB.
4
WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE
OF A SPA OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE
DROWNING.
WARNING: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT
A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C (100°F) CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: BEFORE ENTERING THE SPA OR HOT TUB, MEASURE THE WATER
TEMPERATURE WITH AN ACCURATE THERMOMETER.
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING
STRENUOUS EXERCISE.
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB CAN BE
INJURIOUS TO YOUR HEALTH.
WARNING: DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A LIGHT,
TELEPHONE, RADIO, OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB.
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH
MANUFACTURER'S INSTRUCTIONS.
NOTE: The warning label must be posted near your spa in a readable position
during using your spa.
1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
ASSEMBLY: THE PROVIDED WARNING LABEL
WARNING
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA.
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN
POOR HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT
CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION
CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT,
SOAKING IN HOT WATER FOR LONG PERIODS
CAN HARM YOUR FETUS. MEASURE WATER
TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100°F(38°C)
2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.
5
3. Affix the warning label.
To order the warning label, please contact your local Bestway After Sales Service.
1. Indoor Installation:
Be aware of special requirements if you install the spa indoors.
• Humidity is a natural side effect with SaluSpa installation. First determine the
effects of moisture on exposed wood, paper, etc. in the proposed location. To
minimize these effects, it is best to provide plenty of ventilation to the selected
area. An architect can help determine if more ventilation is needed.
2. Outdoor Installation:
• During filling, draining or when in use, water may spill out of the spa. Therefore the
SaluSpa should be installed near a floor drain.
• Do not leave the spa surface exposed to direct sunlight for long periods of time.
SELECTED LOCATION
IMPORTANT:
Due to the combined weight of the SaluSpa, water, and users, it is
extremely important that the surface where the SaluSpa is installed
is smooth, flat, level and capable of supporting the weight for the entire time the
SaluSpa is installed (not on the carpet or other similar material). If the SaluSpa is
placed on a surface which does not meet these requirements, any damage caused
by improper support is not covered under the manufacturer’s warranty. It is the
responsibility of the SaluSpa owner to assure the integrity of the surface at all times.
GFCI WARNING
IMPORTANT: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED
BEFORE TURNING ON THE PUMP EACH TIME.
WARNING: The GFCI plug must be tested before each use to avoid risk of electric
shock.
WARNING: Before inserting plug into a power outlet, make sure the current rate of
the power outlet is suitable for the pump.
WARNING: Do not use the pump if this test fails. For assistance, please visit the
support section on our website, www.bestwaycorp.com.
WARNING: Using an extension lead or multi plug adaptor with the spa heater can
cause the plug to overheat, causing damage to the equipment and surrounding
items. The spa is a class I electrical appliance and must be connected directly to a
grounded socket. It is recommended to only use a socket which is resistant to
humidity and capable of high power loading. Regularly check the plug and socket for
signs of damage before using the spa – do not use the spa if the plug or socket is
damaged. If you are unsure about the quality of the electrical supply, please consult
a qualified electrician before use.
6
PRE-SETUP CHECK LIST
PARTS CHECKS
Please examine equipment before use.
Notify Bestway® customer service of any
damaged or missing parts at the time of
purchase. Verify that the equipment
components represent the model that you
had intended to purchase. For reference
please use the diagrams below.
MIAMI AIRJET S100104 (60002)
— 71" x 26" / 1.80 m x 66 cm
2
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06123
1
14
P61727ASS18
1
01
P06120
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
7
CANCUN AIRJET S100104 (60004)
— 71" x 26" / 1.80 m x 66 cm
BAHAMAS AIRJET S100104 (60006)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06133
1
14
P61727ASS18
1
01
P06130
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06128
1
14
P61727ASS18
1
01
P06125
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
8
TAHITI AIRJET S100104 (60008)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
58492
1
06
P05343
1
11
P05320
6
03
P06138
1
14
P61727ASS18
1
01
P06135
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P05346
1 17
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
9
BALI AIRJET S100104 (60010)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06315
1
14
P61727ASS18
1
01
P06313
1
07
P05345
112
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P05529
1 18
P61232ASS16
1
19
P06303
1
2
2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
2 - 4
04
P04125
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
8
03
P06153
1
14
P61727ASS18
1
01
P06150
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
205 gal
778 L
1,779 Lb
807 kg
IBIZA AIRJET S100104 (60016)
— 71" x 71" x 26" / 1.80 m x 1.80 m x 66 cm
10
04
54174GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P06321
1
14
P05346
1
01
P06320
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
6
2
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
242 gal
916 L
2,103 Lb
954 kg
PALM SPRINGS AIRJET S100104 (60018)
— 77" x 28" / 1.96 m x 71 cm
11
04
P04125
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05189
1
14
P05346
1
01
P05185
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
8
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
222 gal
840 L
1,938 Lb
879 kg
04
54174GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05195
1
14
P05346
1
01
P05191
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
6
2
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
242 gal
916 L
2,103 Lb
954 kg
HONOLULU AIRJET S100104 (60020)
— 77" x 28" / 1.96 m x 71 cm
HAWAII AIRJET S100104 (60022)
— 71" x 71" x 28" / 1.80 m x 1.80 m x 71 cm
12
04
P04122
1
10
P00217
1
16
P6609ASS16
1 17
/
1
06
P05343
1
12
/
2
03
P05207
1
09
P05524
2
15
P05346
1
01
P05203
1
07
P05345
1
13
P61726ASS18
1
02
P05333
1
08
P06327
1
14
P05344
1
05
P05482
1
11
P05320
6
2
5 - 7 1-2ºF/h
0.5-1ºC/h
320 gal/h
1,211 L/h
0.48-0.69Bar
7-10PSI
297 gal
1123 L
2,548 Lb
1155 kg
04
54175GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05201
1
14
P05346
1
01
P05197
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
8
2
5 - 7 1-2ºF/h
0.5-1ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
314 gal
1190 L
2,668 Lb
1210 kg
ST. MORITZ AIRJET S100104 (60024)
— 85" x 28" / 2.16 m x 71 cm
HELSINKI AIRJET S100104 (60026)
— 71" x 26" / 1.80 m x 66 cm
13
ST.LUCIA AIRJET S100104 (60038)
— 67" x 26" / 1.70 m x 66 cm
04
P05091
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
5
03
P06164
1
14
P61727ASS18
1
01
P06158
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 3 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
160 gal
605 L
1,389 Lb
630 kg
HOLLYWOOD AIRJET S100104 (60060)
— 77" x 26" / 1.96 m x 66 cm
04
54112GASS15
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06202
1
14
P61727ASS18
1
01
P06199
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P05513
118
P61232ASS16
1
19
P06303
1
2
20
P06280
4
2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
240 gal
908 L
2,066 Lb
937 kg
4 - 6
14
ARUBA AIRJET S100104 (60062)
— 67" x 26" / 1.70 m x 66 cm
04
P05091
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
5
03
P06166
1
14
P61727ASS18
1
01
P06161
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 3 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
160 gal
605 L
1,389 Lb
630 kg
FIJI AIRJET S100104 (60086)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06285
1
14
P61727ASS18
1
01
P06282
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
123
P6609ASS16
It is important to follow these suggestions if you are setting up the spa during the winter
period. This will prevent damage to the PVC material and extend the life of your product
drastically.
• If the ambient temperature is below 50°F(10°C), we suggest keeping the package indoor
where the temperature is above 59°F(15°C) for at least 2h before inflation. This will make
the spa liner more flexible and easier to set up.
• Open the package in the same room where the temperature is above 59°F(15°C), and
inflate the spa using the spa heater.
• Position the spa liner outdoor in the desired position, connect the spa heater and fill with
water.
Important: The water temperature used to fill the spa must be above 42.8°F(6°C),
otherwise when you begin to operate with the spa heater, the E03 alarm will appear.
Important: If the Freeze Shield™ system isn’t working, alarms will pop up on the spa. Be
sure to check the status of your spa if the outdoor temperature is below 42.8°F(6°C). In case
of a long-term absence from home when there is a risk of temperatures falling below
42.8°F(6°C), we strongly suggest disassembling the spa and storing it following the storage
procedure. When you assemble the spa, the automatic warm function will turn on. In this
condition, the spa can be used when the temperature is lower than 42.8°F(6°C).
NOTE: The air pressure gauge of the hand pump only shows the air pressure higher than 5 psi, which is
normal. When the air pressure in the product is lower than 5 psi, the air pressure gauge will not show a
value (Only for drop stitch spa).
INSTALLATION
< 50°F(10°C)
> 59°F(15°C)
> 59°F(15°C)
SET-UP
INSTRUCTION
IN WINTER
15
5 6
2
2
ABC
D
HOLLYWOOD BALI
4
HELSINKI
0.48-0.69Bar
7-10PSI
3-6 min
16
When inflating, you will notice that air will be expelled
from the area where the air hose connects to the pump,
this is normal for technique requirements.
Important: Don't cover the holes on the base of the
inflation hose. This operation will over inflate the liner and
damage the structure.
Do not use an air compressor to inflate the pool.
Do not drag the pool on rough ground as this may cause damage to the pool liner.
Inflation time for reference only.
Air Valve Check (for spa with quick inflation/deflation valve)
Always check the air valve carefully before inflation to ensure there is not an air leak.
If the air valve is loose, use the provided wrench to fasten the air valve following
these steps:
With one hand, hold the backside of the air valve from the inner side of the spa wall
and turn the wrench clockwise.
NOTE:
1. Do not over tighten.
2. Do not adjust the air valve connector when the spa is in use.
18
A. LOCK/UNLOCK BUTTON: The pump has a 5-minute auto-lock, this
light will turn on. To lock or unlock the pump, place a finger over the
lock/unlock button for 3 seconds.
B. POWER-SAVING TIMER BUTTON: Designed to help avoid wasting
power by setting the time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing
to leave the heater on at all times.
STEP 1: Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration (From 1-999 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the or button to adjust the hours until time of activation (From 0-999 hours).
3. Press button again or simply touch nothing for 10 seconds to confirm the setting. The
LED will light steadily, and the countdown to heater activation will begin.
To modify the timer settings: Press the button and use the or button to adjust.
Cancel the setting: Press the button for 2 seconds.
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 999 hours;
Reservation time adjustment (the number of hours FROM NOW when the heater will begin to
function) may be set from 0 to 999 hours. If the timer is set at 0 hour, the heating system will
activate immediately.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and
how many hours from now the heating cycle begins. The timer does NOT repeat until reset.
USING THE SPA
Hyperthermia occurs when the internal temperature of the body reaches a level
several degrees above the normal body temperature of 98.6°F(37°C). The symptoms
of hyperthermia include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include
failure to perceive heat, failure to recognize the need to exit spa or hot tub,
unawareness of impending hazard, fetal damage in pregnant women, physical
inability to exit the spa or hot tub, and unconsciousness resulting in the danger of
drowning.
WARNING – The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia.
WARNING: WATER TEMPERATURE IN EXCESS OF 100°F(38°C) CAN BE
INJURIOUS TO YOUR HEALTH.
C. HEAT BUTTON: Use this button to activate the heating system. When
the light above the heat button is red, the heating system is activated.
When the light is green, the water is at the set temperature and the
heating system is at rest.
19
I. WATER FILTER BUTTON: This button turns the filter pump on and off.
The light above the Water Filter Button displays red when activated.
E/G. TEMPERATURE ADJUSTMENT BUTTONS: Pressing the
Temperature Increase or Decrease buttons will cause the LED to flash.
When it is flashing you can adjust to the desired temperature setting. If
you hold these buttons down the values will rapidly increase or decrease.
The new and desired temperature setting will remain on the LED display
for 3 seconds to confirm the new value.
NOTE: The default temperature is 95°F(35°C).
NOTE: Temperature adjustment ranges from 68°F(20°C) to 104°F(40°C).
F. ON/OFF BUTTON: Press this button for 2 seconds to active the control
panel buttons and the light turns to green. Press this button for 2 seconds
to turn off all currently activated functions.
POWER-SAVING TIMER LED:
This flashing LED means you are setting the heating duration. The light will
be on when the heating function starts to work.
This flashing LED means you are setting the number of hours FROM NOW
when the heater will activate. When the light is on, the Power-Saving
Timer function is set.
D. MASSAGE SYSTEM BUTTON: Use this button to activate the
massage system, which has a 30-minute auto-shutoff feature. The light
above the Massage System Button displays red when activated.
IMPORTANT: Do not run the Massage system when the cover is
attached. Air can accumulate inside the spa and cause irreparable
damage to the cover and bodily harm.
NOTE: Heat and massage system work together to create a warm
massage experience.
H. CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed
in either Fahrenheit or Celsius.
NOTE: If the heating system is activated the filtration system will
automatically start.
NOTE: After turning off the heating system the filtration system will
continue to operate.
NOTE: If the spa heater is on when the water temperature is below
42.8°F(6ºC), the heating system will warm the water until 50°F(10ºC)
automatically.
NOTE: The WATER HEATER rate may change in the conditions below:
• When the outdoor temperature is below 59°F(15°C).
• If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a
minute.
The water temperature as tested by an external thermometer may vary from the
temperature as displayed on the spa panel by as much as approximately 35.6°F(2°C).
20
Ambient Temperature
50ºF(10ºC)
59ºF(15ºC)
68ºF(20ºC)
77ºF(25ºC)
86ºF(30ºC)
Water Temperature
50ºF(10ºC)
59ºF(15ºC)
68ºF(20ºC)
77ºF(25ºC)
86ºF(30ºC)
Set Temperature
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
104ºF(40ºC)
Heating Duration
32 h
26 h
20 h
14 h
9 h
IMPORTANT
To reach 104°F(40°C), the heating duration required is based on the starting water
temperature and ambient temperature, the data below is purely for reference. To
display the current water temperature, run the filter system for at least a minute.
Power Rate Massage Tube Blower Heat Element Water Pump
11.3A at 20ºC 0.7A
110-120V AC,
60Hz, Single Phase
12A at 20ºC
6.5A
• Be sure to cover the spa with the spa
cover whenever the heating function is
activated. Leaving the spa uncovered
will increase the heating duration
required.
• When the spa is assembled with water,
do not switch off the spa heater if the
temperature is lower than 42.8°F(6ºC).
WINTER USE INSTRUCTIONS
•
You can keep the spa on during winter when the temperature is lower than
42.8°F(
6°C
)
. The Freeze Shield™ system automatically keeps the water temperature
between
42.8°F(
6°C
)
and
50°F(
10°C
)
, and it will prevent the water from freezing.
Important:
If the water temperature is below
42.8°F(
6°C
)
, the spa heater must always
be on. In this mode, the Freeze Shield™ system can keep the internal temperature
between
42.8°F(
6°C
)
and
50°F(
10°C
)
to prevent damage, such as water freezing in the
pipes or the circulation system.
Important:
If the Freeze Shield™ system isn’t working, alarms will pop up on the spa.
Be sure to check the status of your spa if the outdoor temperature is below
42.8°F(
6°C
)
. In case of a long-term absence from home when there is a risk of
temperatures falling below
42.8°F(
6°C
)
, we strongly suggest disassembling the spa
and storing it following the storage procedure.
•
Any damage as a result of using the spa in these conditions is the responsibility of the
customer. Do not use the spa when the ambient temperature reaches 14°F(-10°C).
21
Cover Maintenance
The cover shall be cleaned inside and out periodically using a suitable solution that
includes adequate disinfection (e.g. 10 mg/l of Free Chlorine).
Filter Cartridge Maintenance
To ensure your spa water stays clean, check and clean your filter cartridges every
day follow the steps below.
NOTE: We recommend changing your filter cartridges every week or, if the filter
cartridges remain soiled and discolored, they should be replaced.
CAUTION: You must ensure the pump is unplugged before beginning spa
maintenance to avoid risk of injury or death.
MAINTENANCE
Adding Air: Your spa will require additional air to be added from time to time.
Changes in temperature from day to night will change the pressure in the spa and
may cause a certain amount of deflation. Please follow the assembly instructions and
inflate to the accurate pressure needed.
When you need to use the pump for inflation, please block the hoses to prevent
water from escaping, then disconnect the pump, screw on the cap (P00217) to avoid
water coming out from the air pipe.
P00217
Filter Set
Filter Cartridge
Water Maintenance
Many pollutants in the water settle on surfaces below the water line. These
pollutants can cause bacterial, algal or fungal growth. It is recommended that spas
are cleaned as regularly as necessary. After a time, tenacious stains or biofilms may
develop on the accessible surfaces below the water line or high concentrations of
salts or unwanted reaction by-products may also occur. Depending on hygienic
condition, cleanliness, visibility, odour, debris and stains, it is recommended to
change the water completely and clean/disinfect the spa. When emptying the spa,
the regulations and the instructions for draining the water shall be observed.
Keeping your spa water clean and chemically balanced is necessary. Simply
cleaning the filter cartridge is not enough for proper maintenance, we recommend
you use pool chemicals to maintain water chemistry and chlorine or bromine tablets
(do not use granules) with the chemical dispenser.
22
NOTE: Remove the chemical dispenser from spa when the spa is in use.
IMPORTANT: After performing chemical maintenance and before using the spa, use
a test kit (not included) to test the water chemistry. We recommend maintaining your
water as below table.
Important: Add chemical liquid in small doses and in
the center of the pool avoid directly contact of the
chemical with the spa surface, the direct contact of
chemical with spa material will damage the material
and discolored the surface.
NOTE: Damage resulting from chemical imbalance is not covered by the warranty.
Pool chemicals are potentially toxic and should be handled with care. There are
serious health risks from chemical vapors and the incorrect labeling and storage of
chemical containers. Please consult your local pool supply retailer for more
information about chemical maintenance. Pay close attention to the chemical
manufacturer’s instructions. spa damage resulting from misuse of chemicals and
mismanagement of spa water is not covered by the warranty.
Important: Over usage of chemical will discolored the printing and all points of the
spa material, in worse case damage the structure of the spa liner.
pH
7.4-7.6
Total Alkalinity
80-120ppm
Free Chlorine
2-4ppm
Using chemical tablets (not included):
Using chemical liquid (not included):
Water quality will be directly related to frequency of use, number of users and
overall maintenance of the spa. The water should be changed every
3 days if there is no chemical treatment being performed with the water.
It is highly recommended to use tap water for spa filling to minimize the influence of
unwanted content, such as minerals. Barefoot areas and relaxing areas shall be
cleaned as well. No cleaning water may flow into the spa or spa water cycle. The
dirt and cleaning agents shall be rinsed carefully to drain in the spa surround.
Note: We recommend you take a shower before using your SaluSpa, as cosmetic
products, lotions, and other residues on the skin can quickly degrade water
quality.To use the chemical dispenser, please follow the below instruction.
Important: Don't use granulate tablet or throw the tablet directly in the water, the
chemical will deposit on the bottom and damage the material and discolored the PVC.
23
DRAINING THE SPA
3. 4.
5.
NOTE: Dry the spa pool.
DISASSEMBLY AND STORAGE
P00217
NOTE: Lift up the spa when there is
only a little water left. Damages to
the handles are not covered under
the warranty.
NOTE: Dry the spa pool
2. 3. 4.
6. 7.
1. 5.
8.
Only for Drop stitch Spa
6.
For Bali and Hollywood Spas:
You may find steam inside the air chamber, and mold may appear after
storage if there is water inside. Please unscrew the valve and use the
pipe to blow into the air chamber until you dry all the steam inside. This
operation may take 2-5 hours.
1. 2.
24
CLEANING THE SPA
Detergent residues and dissolved solids from bathing suits and chemicals may build
up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.
NOTE: DO NOT use hard brushes or abrasive cleaners.
Make sure the spa and pump are completely dry. This is essential to extend the life of
the spa. We recommend using the pump to blow dry the spa, pump and pipes.
Remove the filter sets and discard the used filter cartridges. Re-attach the two
stopper caps onto the spa’s inlet and outlet valves. It is recommended you store the
spa in its original package in a warm [above 59°F(15°C)] and dry place.
DEFLATION
Your spa is equipped with a deflation function to remove all the air from inside the
chamber to make it easier to pack and store.
REPAIR
For PVC part.
If the spa is torn or punctured, use the provided underwater adhesive repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 seconds before inflation.
For Tritech PVC material.
If the spa is torn or punctured, use the provided PVC repair patch and glue (not included) following these steps:
1. Clean and dry area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3. Use glue (not included) to coat the one side of the newly cut patch. Make sure the glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the damaged area.
5. Smooth out any bubbles of air that may be trapped underneath, and press firmly for two minutes.
6. The product is once again ready for use. Repeat this process should further leaks occur.
7. Wait 30 minutes before inflation.
Screw valve
Quick inflation/deflation valve
P61727ASS18
P61726ASS18
P05344
P61726ASS18
25
Problems Probable Causes Solutions
The control panel has an auto-lock,
which is activated after 5 minutes of
inactivity. The LED display has one
icon: If the lock icon is highlighted,
the control panel is locked.
- Control panel is not activated.
Water leaks from the adapters
between the pump and spa
What kind of chemicals should be
used for water maintenance?
GFCI test failed
Control panel not working
Water is not clean
Spa pool leakage
Pump adapters are not level with
the spa adapters
Massage System does not work
Pump does not heat properly
Pump does not operate - Power failure
- GFCI broken
- Check power source
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Set to a higher temperature refer to section pump operation
- Clean/replace the filter cartridge refer to section filter cartridge cleaning
and replacement
- Unplug the pump, and put the plug in a dry, cool place. Only
restart the pump when the water temperature reaches 95°F(35°C) or
lower
- Attach the cover.
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Unplug the pump and wait two hours until the pump has cooled. Insert
the plug and press the massage system button
- Press the massage system button to reactivate
- For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if so,
use the provided wrench to fasten the air-valve following these steps:
1. Deflate the spa.
2. With one hand, hold the backside of the air valve from the inner
side of the spa wall and turn the wrench clockwise.
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning and
Replacement section)
- Refer to the chemical manufacturer’s instructions
- To unlock the control panel, press the button for 3 seconds.
If the control panel will not unlock, restart the pump – unplug and
plug in the pump.
- Press the on/off button for 2 seconds. If the problem persists,
for assistance, please visit the support section on our website,
www.bestwaycorp.com.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
- Insert the stopper caps on the spa ports to prevent the water from
escaping and disconnect the pump. Check if the seals are in place.
- If the seals are not in the correct position open the gears and place the , ,
seals in correct position.
- If the seals are damaged, they must be replaced. For assistance,
please visit the support section on our website ，
www.bestwaycorp.com.
- If the seals are in correct position the adapters are not tightened ,
correctly. Connect the pump to the spa, hand-tighten the adapters and ,
remove the stopper caps from the spa ports. If there is leakage, tighten
the adapter until there is no leakage.
- Temperature set too low
- Dirty Filter Cartridge
- The thermal cut-out cut off
- Spa is not covered
- Heating element failed
- Air Pump is overheating
- The massage system
stops automatically
- Air pump is broken
- One characteristic of PVC is that it
changes shape, which is normal
- Spa is torn or punctured
- Air valve is loose
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
There is a defect in your spa
Please consult your local chemical supplier for information about chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions.
- Seals are missing inside the pump
adapters
- Seals are not in correct position
- Seals are damaged
- Adapters are not tightened correctly
TROUBLESHOOTING
Bestway strives to provide the most trouble-free spas on the market.
If you experience any problems whatsoever, do not hesitate to contact Bestway or your authorized dealer. Here are some
helpful tips to help you to diagnose and rectify some common sources of trouble.
26
CAUSES REASONS SOLUTIONS
The water flow sensors work
without pressing the filter or heat
button.
1. The water flow sensor flags didn’t fall back into the
correct position.
2. The water flow sensors are broken.
1. Unplug the plug, strike the side of the pump but not violently, and plug it back in.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
After starting or during the
functions of filtering or/and
heating, the water flow sensors do
not detect water flow.
1. You forgot to remove the 2 stopper caps from inside
the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your hand
in front of the outlet pipe inside the pool to check if
you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm oppears, then
the water flow sensors are broken.
4. Filter blockage
5. Bent pipes or poor water flow through the plastic
pipes of the liner
6. Debris screens are blocked: debris screens can
become blocked by hard water due to calcium
build-up.
7. Perished washers
The washers within the spa couplings may have
become perished or worn.
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If no
alarm appears, clean or change the filter cartridges install the filter set inside the
pool.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
4. Clean the filter and check for damage. Replace or re-install as necessary. For
assistance, please visit the support section on our website,
www.bestwaycorp.com.
5. Please check through the spa connection to see if the pipes are bending. For
assistance, please visit the support section on our website,
www.bestwaycorp.com.
6. Empty the spa and place a garden hose inside the pipes to wash the debris. To
be sure all debris is removed, perform the operation from the outside and inside
of the spa.
Use a toothbrush to remove any stubborn debris.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
7. Check the washers inside the coupling for damage. Unscrew the couplings and
remove the washer for further inspection.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer reads
the water temperature below
40°F(4°C).
1. The water temperature is lower than 40°F(4°C).
2. If the water temperature is higher than 44.6°F(7°C),
the pump’s thermometer is broken.
1. The spa is not designed to operate with water temperatures lower than
40°F(4ºC). Unplug the pump and only re-start the pump when the water
temperature reaches 43°F(6°C).
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer reads
the water temperature over
119°F(48°C).
1. The water temperature is over 119°F(48°C).
2. The ambient temperature is higher than 104°F(40°C)
or the spa is exposed to direct sunlight for an
extended period of time.
3. If the water temperature is lower than 113°F(45°C),
the pump’s thermometer is broken.
1. The spa is not designed to operate with water temperatures greater than
104°F(40°C). Unplug the pump and only re-start the pump when the water
temperature reaches 100°F(38°C) or lower.
2. Disconnect the plug, detach the pump and drain the spa. After 15 minutes,
reattach the pump, reconnect the plug and restart the heating function. If the
alarm appears again, consider moving the spa to another location without
direct sunlight.
3. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The pump’s thermometer
connections have issues.
1. The pump’s thermometer connectors don’t work
properly.
2. The pump’s thermometer is broken.
For assistance, please visit the support section on our website,
www.bestwaycorp.com.
The thermal cut-out cut off. 1. The ambient temperature is over 122°F(50°C) or
the pump is directly under the sunshine.
2. The thermal cut-out is broken.
1. Unplug the pump, and put the pump in a dry, cool place. Only re-start the
pump when the water temperature reaches 93.2°F(34°C) or lower.
2. For assistance, please visit the support section on our website,
www.bestwaycorp.com.
ERROR CODES
27
28
MANUEL DE L’UTILISATEUR
FR
VISITEZ LA CHAÎNE YOUTUBE DE
BESTWAY
CONSIGNES DE SÉCURITÉ IMPORTANTES
pg 031
LISTE DE CONTRÔLE AVANT
L’INSTALLATION
pg 035
INSTALLATION
pg 043
INSTRUCTIONS D’INSTALLATION EN HIVER
pg 043
UTILISATION DU SPA
pg 047
ENTRETIEN
pg 050
DÉMONTAGE ET RANGEMENT
pg 052
DÉPANNAGE
pg 054
CODES D’ERREUR
pg 055
POUR LES VIDÉOS D’INSTRUCTIONS
VEUILLEZ VISITER
BEST YCWA ORP.C ORT OM/SUPP
TABLE DES MATIÈRES
V
i
s
i
t
e
z
w
w
w
.
b
e
s
t
w
a
y
c
o
r
p
.
c
o
m
/
s
u
p
p
o
r
t
p
o
u
r
o
b
t
e
n
i
r
d
e
l
’
a
i
d
e
NOUS SUGGÉRONS DE NE PAS
RAMENER LE PRODUIT AU MAGASIN
DES QUESTIONS ? DES PROBLÈMES ?
DES PIÈCES MANQUANTES ?
Pour les FAQ, les notices, les vidéos ou
les pièces détachées, veuillez visiter
bestwaycorp.com/support
30
CONSIGNES DE SÉCURITÉ IMPORTANTES
ATTENTION
D’IMPORTANTES CONSIGNES DE
SÉCURITÉ
Lors de l’utilisation de cet équipement électrique, vous devez toujours suivre les consignes de
sécurité de base, y compris les précautions suivantes.
RESPECTEZ ET CONSERVEZ CES
INSTRUCTIONS.
AVERTISSEMENT – Pour réduire les risques de blessure, ne permettez pas aux enfants d’utiliser
ce produit à moins d’être étroitement surveillé tout le temps.
Un connecteur de fils est fourni avec ce dispositif pour raccorder un conducteur en cuivre massif de
6 AWG (13,3 mm
2
) minimum entre ce dispositif et tout équipement métallique, les boîtiers
métalliques de l’équipement électrique, les conduits d’eau en métal ou les conduits à moins de
5 pieds (1,5 m) du dispositif.
DANGER – Risque de blessure.
a) Remplacez immédiatement le cordon endommagé.
b) N’enterrez pas le cordon.
c) Ne branchez que sur une prise de terre.
ATTENTION - Ce produit est fourni avec un disjoncteur de fuite de terre (GFCI) intégré avec la fiche
d’alimentation à l’extrémité du cordon. Il faut tester le GFCI avant chaque utilisation. Quand le
produit est en marche, appuyez sur la touche de test du GFCI et le produit devrait cesser de
fonctionner. Appuyez sur la touche de réinitialisation sur le GFCI et le produit devrait recommencer à
fonctionner normalement. Quand le produit ne fonctionne pas de cette manière, cela veut dire qu’un
courant à la masse circule et donc qu’il existe un risque d'électrocution. Mettez hors tension jusqu’à
ce que vous ayez identifié et corrigé la panne.
DANGER – Danger de Noyade. Ne pas laisser d’enfants s’approcher sans autorisation.
Pour éviter les accidents, assurez-vous que les enfants ne puissent jamais utiliser le spa sans
surveillance.
DANGER – Risque de Blessure. Les raccords d’aspiration de ce spa sont dimensionnés pour
répondre au débit d’eau spécifique créé par la pompe. Si vous avez besoin de changer les raccords
d’aspiration ou la pompe, vérifiez que les débits soient compatibles. Ne faites jamais fonctionner la
spa si les raccords d'aspiration sont brisés ou manquants. Ne jamais remplacer un raccord
d'aspiration par un autre dont le débit nominal est inférieur à celui qui est indiqué sur le raccord
d'aspiration original.
DANGER – Danger D’Électrocution. Installez-le à au moins 5 pieds (1,5 m) de toutes les surfaces
métalliques. En alternative, il est possible d’installer un spa à moins de 5 pieds des surfaces
métalliques si chacune d’entre elles est raccordée de manière permanente par un conducteur en
cuivre massif de 6 AWG (13,3 mm
2
) minimum à un connecteur de fils sur un bornier prévu pour cela.
DANGER – Danger D’Électrocution. Ne laissez aucun appareil électrique, comme une lampe, un
téléphone, une radio ou une télévision, à moins de 5 pieds (1,5 m) d’un spa.
ATTENTION – Pour réduire les risques de blessure:
a) l’eau d’un spa ne doit jamais dépasser les 40°C. Les températures de l'eau
comprises entre 100°F (38°C) et 40°C sont considérées comme étant sûres pour un adulte en
bonne santé.
Une température moindre est recommandée pour les jeunes enfants et lorsque le spa est utilisé
pendant plus de dix minutes.
b) Étant donné qu’une température excessive de l’eau risque d’être dangereuse durant les premiers
mois de grossesse, les femmes enceintes ou en quête de grossesse doivent limiter la
température de l’eau à 100°F (38°C).
c) Avant d’entrer dans le spa, l’utilisateur doit mesurer la température de l’eau avec un thermomètre
31
précis étant donné que la tolérance des appareils de réglage de la température de l’eau varie.
d) La consommation d’alcool, de drogue ou de médicament avant ou en pendant l’utilisation d’un
Spa peut faire perdre connaissance et engendre donc un risque de noyade.
e) Les personnes obèses et avec des antécédents cardiaques, des problèmes de tension artérielle,
de circulation du sang ou de diabète doivent consulter un médecin avant d’utiliser le Spa.
f ) Les personnes sous traitement doivent consulter un médecin avant d’utiliser un spa car certains
médicaments peuvent engendrer un risque de noyade ou encore avoir des effets sur le rythme
cardiaque, la pression artérielle et la circulation du sang.
ATTENTION : POUR EVITER LES RISQUES D’ELECTROCUTION, NE PAS UTILISER LE SPA EN
CAS DE PLUIE.
ATTENTION : L’eau attire les enfants; Toujours recouvrir le spa de sa protection après chaque usage.
ATTENTION – POUR RÉDUIRE LES RISQUES DE BLESSURE: N’ajoutez jamais d’eau ayant une
température supérieure à 104°F (40°C) dans le spa.
CONSULTEZ VOTRE MÉDECEIN POUR
D’ÉVENTUELLES RECOMMANDATIONS.
ATTENTION :
il est fortement recommandé de ne pas déplier et gonfler le spa si la température ambiante est
inférieure à 59°F (15°C). Nous suggérons de gonfler le spa à l’intérieur, puis de continuer
l’installation à l’extérieur. Si la température extérieure est inférieure à 42,8°F (6°C), le chauffage du
spa doit toujours rester allumé. De cette manière, le système Freeze Shield™ peut maintenir la
température à l’intérieur du spa entre 42,8°F (6°C) et 50°F (10°C) pour éviter les dégâts, comme
par exemple l’eau gelant dans les tuyaux du système de circulation.
IMPORTANT : si le système Freeze Shield™ ne fonctionne pas, les alarmes se déclencheront
dans le spa. Veillez à bien vérifier l’état de votre spa si la température extérieure est inférieure à
42,8°F (6°C). En cas d’absence prolongée de votre domicile, lorsqu’il existe un risque de baisse de
la température en dessous de 42,8°F (6°C), nous conseillons vivement de démonter le spa et de le
ranger en suivant la procédure de rangement.
ATTENTION : Ne pas utiliser le Spa seul.
ATTENTION : Toujours entrer et sortir du spa lentement et en faisant attention. Les surfaces
humides glissent.
ATTENTION : Pour éviter d’endommager la pompe, le spa ne doit jamais fonctionner sans eau.
ATTENTION : Sortir immédiatement du Spa en cas de malaise ou d’endormissement.
REMARQUE: Bien examiner l’équipement avant usage. Informez Bestway à l’adresse du service
clientèle répertoriée dans ce manuel en cas de dommage ou pièces manquantes au moment de
l'achat. Vérifiez que les composants de cet équipement correspondent bien au modèle que vous
avez voulu acheter.
CONSERVEZ CES INSTRUCTIONS
ATTENTION : NE PAS LAISSER LES ENFANTS UTILISER UNE CUVE DE
RELAXATION SANS SURVEILLANCE.
ATTENTION : POUR ÉVITER QUE LES CHEVEUX OU UNE PARTIE DU CORPS
PUISSENT ÊTRE ASPIRÉS, NE PAS UTILISER UNE CUVE DE RELAXATION SI
LES GRILLES DE PRISE D'ASPIRATION NE SONT PAS TOUTES EN PLACE.
ATTENTION : LES PERSONNES QUI PRENNENT DES MÉDICAMENTS ET (OU)
ONT DES PROBLÈMES DE SANTÉ DEVRAIENT CONSULTER UN MÉDECIN
AVANT D'UTILISER UNE CUVE DE RELAXATION.
ATTENTION : LES PERSONNES ATTEINTES DE MALADIES INFECTIEUSES NE
DEVRAIENT PAS UTILISER UNE CUVE DE RELAXATION.
ATTENTION : POUR ÉVITER DES BLESSURES, USER DE PRUDENCE EN
ENTRANT DANS UNE CUVE DE RELAXATION ET EN SORTANT.
ATTENTION : POUR ÉVITER L'ÉVANOUISSEMENT ET LA NOYADE
ÉVENTUELLE, NE PRENDRE NI DROGUE NI ALCOOL AVANT D'UTILISER UNE
32
CUVE DE RELAXATION NI QUAND ON S'Y TROUVE.
ATTENTION : LES FEMMES ENCEINTES, QUE LEUR GROSSESSE SOIT
CONFIRMÉE OU NON, DEVRAIENT CONSULTER UN MÉDECIN AVANT
D'UTILISER UNE CUVE DE RELAXATION.
ATTENTION : IL PEUT ÊTRE DANGEREUX POUR LA SANTÉ DE SE PLONGER
DANS DE L'EAU À PLUS DE 38°C.
ATTENTION : AVANT D'UTILISER UNE CUVE DE RELAXATION, MESURER LA
TEMPÉRATURE DE L'EAU À L'AIDE D'UN THERMOMÈTRE PRÉCIS.
ATTENTION : NE PAS UTILISER UNE CUVE DE RELAXATION IMMÉDIATEMENT
APRÈS UN EXERCICE FATIGANT.
ATTENTION : L'UTILISATION PROLONGÉE D'UNE CUVE DE RELAXATION
PEUT ÊTRE DANGEREUSE POUR LA SANTÉ.
ATTENTION : NE PAS PLACER D'APPAREIL ÉLECTRIQUE (LUMINAIRE,
TÉLÉPHONE, RADIO, TÉLÉVISEUR, ETC) À MOINS DE 1.5 M DE CETTE CUVE
DE RELAXATION.
ATTENTION : LA TENEUR DE L'EAU EN MATIÈRES DISSOUTES DOIT ÊTRE
CONFORME AUX DIRECTIVES DU FABRICANT.
MONTAGE: L’ÉTIQUETTE DE MISE EN GARDE FOURNIE
ATTENTION
RÉDUISEZ LE RISQUE D’ÉLECTROCUTION
1. NE PLACEZ JAMAIS UN APPAREIL ELECTRIQUE A MOINS DE 1,52 M (5 PIEDS) DU SPA.
RÉDUISEZ LE RISQUE DE NOYADE CHEZ LES ENFANTS
1. SUPERVISEZ TOUJOURS LES ENFANTS.
2. FIXEZ LA COUVERTURE DU SPA APRES CHAQUE UTILISATION.
RÉDUISEZ LE RISQUE DE SURCHAUFFE
1. CONSULTEZ UN MEDECIN AVANT DE L’UTILISER SI VOUS ETES ENCEINTE,
DIABETIQUE, SI VOUS AVEZ UNE SANTE FRAGILE OU QUE VOUS SUIVEZ UN
TRAITEMENT MEDICAL.
2. SORTEZ IMMEDIATEMENT SI VOUS VOUS SENTEZ MAL, SI VOUS ETES PRIS DE
VERTIGE OU SI VOUS AVEZ ENVIE DE DORMIR. LA CHALEUR DU SPA PEUT
PROVOQUER UNE HYPERTHERMIE ET UNE PERTE DE CONNAISSANCE.
3. LA CHALEUR DU SPA ASSOCIEE A L’ALCOOL, DES DROGUES OU DES MEDICA
MENTS PEUT ENTRAINER LA PERTE DE CONNAISSANCE.
SI VOUS ÊTES ENCEINTE,
L’IMMERSION DANS DE L’EAU
CHAUDE PENDANT DE LONGUES PERIODES PEUT NUIRE AU FŒTUS. MESUREZ LA
TEMPERATURE DE L’EAU AVANT D’Y ENTRER.
1. N’ENTREZ PAS DANS LE SPA SI L’EAU SE TROUVE A UNE TEMPERATURE
SUPERIEURE A 100°F (38°C)
2. NE RESTEZ PAS DANS LE SPA PENDANT PLUS DE 10 MINUTES.
33
LISTE DE CONTRÔLE AVANT L’INSTALLATION
CONTRÔLE DES PIÈCES
Veuillez examiner l’équipement avant de
l’utiliser.
Informez le service après-vente de
Bestway® si des pièces sont abîmées ou
manquantes au moment de l’achat.
Vérifiez que les composants de
l'équipement correspondent au modèle
que vous souhaitiez acheter. Pour les
références, veuillez utiliser les schémas
ci-dessous.
35
MIAMI AIRJET S100104 (60002)
— 71" x 26" / 1.80 m x 66 cm
2
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06123
1
14
P61727ASS18
1
01
P06120
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
36
CANCUN AIRJET S100104 (60004)
— 71" x 26" / 1.80 m x 66 cm
BAHAMAS AIRJET S100104 (60006)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06133
1
14
P61727ASS18
1
01
P06130
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06128
1
14
P61727ASS18
1
01
P06125
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
37
TAHITI AIRJET S100104 (60008)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
58492
1
06
P05343
1
11
P05320
6
03
P06138
1
14
P61727ASS18
1
01
P06135
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P05346
1 17
P6609ASS16
1
2
2 - 4 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
BALI AIRJET S100104 (60010)
— 71" x 26" / 1.80 m x 66 cm
04
54123GASS17
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06315
1
14
P61727ASS18
1
01
P06313
1
07
P05345
112
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P05529
1 18
P61232ASS16
1
19
P06303
1
2
2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
177 gal
669 L
1,534 Lb
696 kg
2 - 4
38
04
P04125
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
8
03
P06153
1
14
P61727ASS18
1
01
P06150
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
205 gal
778 L
1,779 Lb
807 kg
IBIZA AIRJET S100104 (60016)
— 71" x 71" x 26" / 1.80 m x 1.80 m x 66 cm
04
54174GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P06321
1
14
P05346
1
01
P06320
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
6
2
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
242 gal
916 L
2,103 Lb
954 kg
PALM SPRINGS AIRJET S100104 (60018)
— 77" x 28" / 1.96 m x 71 cm
39
04
P04125
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05189
1
14
P05346
1
01
P05185
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
8
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
222 gal
840 L
1,938 Lb
879 kg
04
54174GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05195
1
14
P05346
1
01
P05191
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
6
2
4 - 6 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
242 gal
916 L
2,103 Lb
954 kg
HONOLULU AIRJET S100104 (60020)
— 77" x 28" / 1.96 m x 71 cm
HAWAII AIRJET S100104 (60022)
— 71" x 71" x 28" / 1.80 m x 1.80 m x 71 cm
40
04
P04122
1
10
P00217
1
16
P6609ASS16
1 17
/
1
06
P05343
1
12
/
2
03
P05207
1
09
P05524
2
15
P05346
1
01
P05203
1
07
P05345
1
13
P61726ASS18
1
02
P05333
1
08
P06327
1
14
P05344
1
05
P05482
1
11
P05320
6
2
5 - 7 1-2ºF/h
0.5-1ºC/h
320 gal/h
1,211 L/h
0.48-0.69Bar
7-10PSI
297 gal
1123 L
2,548 Lb
1155 kg
04
54175GASS18
1
09
P00217
1
15
P6609ASS16
1 16
P05767
1
06
P05343
1
11
/
2
03
P05201
1
14
P05346
1
01
P05197
1
07
P05345
1 12
P61726ASS18
1
02
P05333
1
08
P05524
2
13
P61727ASS18
1
05
P05341
1
10
P05320
8
2
5 - 7 1-2ºF/h
0.5-1ºC/h
320 gal/h
1,211 L/h
0.08Bar
1.2PSI
314 gal
1190 L
2,668 Lb
1210 kg
ST. MORITZ AIRJET S100104 (60024)
— 85" x 28" / 2.16 m x 71 cm
HELSINKI AIRJET S100104 (60026)
— 71" x 26" / 1.80 m x 66 cm
41
ST.LUCIA AIRJET S100104 (60038)
— 67" x 26" / 1.70 m x 66 cm
04
P05091
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
5
03
P06164
1
14
P61727ASS18
1
01
P06158
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1
2
2 - 3 2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
160 gal
605 L
1,389 Lb
630 kg
HOLLYWOOD AIRJET S100104 (60060)
— 77" x 26" / 1.96 m x 66 cm
04
54112GASS15
1
09
F4C009B-02ASS17
1
15
P05346
1
06
P05343
1
11
P05320
6
03
P06202
1
14
P61727ASS18
1
01
P06199
1
07
P05345
1 12
/
2
02
P05333
1
08
P05524
2
13
P61726ASS18
1
05
P6931ASS16
1
10
P00217
1
16
P6609ASS16
1 17
P05513
118
P61232ASS16
1
19
P06303
1
2
20
P06280
4
2-3ºF/h
1-1.5ºC/h
320 gal/h
1,211 L/h
0.034-0.055Bar
0.5-0.8PSI
240 gal
908 L
2,066 Lb
937 kg
4 - 6
123
P6609ASS16
Il est important de suivre ces suggestions si vous installez le spa pendant l’hiver. Cela vous
évitera d’endommager le PVC et prolongera considérablement la durée de vie de votre produit.
• Si la température ambiante est inférieure à 50 °F (10 °C), nous suggérons de conserver le
colis à l’intérieur où la température est supérieure à 59 °F (15 °C) pendant au moins 2h avant
de le gonfler. Cela rendra le liner du spa plus flexible et plus facile à installer.
• Ouvrez le colis dans la même pièce ou la température est supérieure à 59 °F (15 °C), puis
gonflez le spa au moyen du chauffage du spa.
• Positionnez le liner du spa à l’extérieur dans la position souhaitée, raccordez le chauffage du
spa et remplissez le spa d’eau.
Important : la température de l'eau utilisée pour remplir le spa doit être supérieure à
42,8 °F (6 °C), sinon lorsque vous commencerez à le faire fonctionner avec le chauffage du
spa, l’alarme E03 s’affichera.
Important : si le système Freeze Shield™ ne fonctionne pas, les alarmes se déclencheront
dans le spa. Veillez à bien vérifier l’état de votre spa si la température extérieure est inférieure
à 42,8 °F (6 °C). En cas d’absence prolongée de votre domicile, lorsqu’il existe un risque de
baisse de la température en dessous de 42,8 °F (6 °C), nous conseillons vivement de démonter
le spa et de le ranger en suivant la procédure de rangement. Lorsque vous montez le spa, la
fonction chaleur automatique s’allumera. Dans cette condition, le spa peut être utilisé lorsque la
température est inférieure à 42,8 °F (6 °C).
INSTALLATION
< 50°F(10°C)
> 59°F(15°C)
> 59°F(15°C)
INSTRUCTIONS
D’INSTALLATION
EN HIVER
43
REMARQUE :le manomètre de la pompe à main ne montre que la pression de l’air supérieure à 5 psi, ce
qui est normal. Lorsque la pression de l’air dans le produit est inférieure à 5 psi, le manomètre n’indique
aucune valeur (uniquement pour le spa en Drop Stitch
TM
).
5 6
2
2
ABC
D
HOLLYWOOD BALI
4
HELSINKI
0.48-0.69Bar
7-10PSI
3-6 min
44
max
min
MAX.
MIN.
109
7 8
TEST GFCI
11.2 HOLLYWOOD
11.1
45
A. BOUTON DE VERROUILLAGE/D errouillage
automatique de 5 minutes, ce voyant s’allumera. Pour verrouiller ou déverrouiller la
pompe, placez un doigt sur le bouton de verrouillage/déverrouillage pendant 3 secondes.
B. BOUTON MINUTERIE ÉCONOMIE D’ÉNERGIE : conçu pour éviter de gaspiller de
l'énergie en réglant l'heure et la durée du cycle de chauffage du spa.
Ceci vous permettra de profiter de votre spa quand vous le souhaitez sans avoir à laisser
le chauffage allumé en permanence.
ÉTAPE N° 1 : Définissez la durée de chauffage
1. Appuyez sur le bouton ajoutez le la LED commence à clignoter.
2. Appuyez sur le bouton ou our régler la durée de chauffage (de 1 à 999 heures).
3. Appuyez à nouveau sur le bouton pour confirmer la durée du chauffage.
ÉTAPE N° 2 : Définissez dans combien d'heures À PARTIR DE MAINTENANT le chauffage doit s'activer
1. Après avoir réglé la durée de chauffage, la LED commence à clignoter.
2. Appuyez sur les boutons ou pour ajuster les heures jusqu'au moment de l'activation (de 0 à 999 heures).
3. Appuyez à nouveau sur le bouton ou ne touchez rien pendant 10 secondes pour valider la configuration. La
LED s'allumera en continu et le compte à rebours jusqu'à l'activation du chauffage commencera.
Pour modifier les paramètres de la minuterie : appuyez sur le bouton et utilisez le bouton ou pour procéder au réglage.
Annulez le paramètre : appuyez sur le bouton pendant 2 secondes.
REMARQUE : après avoir effectué le réglage, l’écran affiche alternativement la température actuelle et l’heure.
REMARQUE : la minuterie (durée pendant laquelle le chauffage est ACTIVÉ) peut être réglée entre 1 et 999 heures ;
le réglage du temps de réservation (le nombre d'heures À PARTIR DE MAINTENANT, lorsque l'appareil de
chauffage commencera à fonctionner) peut être réglé de 0 à 999 heures. Si la minuterie est réglée sur 0 heure, le
système de chauffage se déclenchera immédiatement.
Notez que la minuterie n'est valable qu'une fois par utilisation : l'utilisateur règle la durée du cycle de chauffage et le
nombre d'heures jusqu'au moment où le cycle de chauffage commencera. La minuterie NE SE répète PAS tant
qu'elle n'est pas réinitialisée.
UTILISATION DU SPA
L’hyperthermie se produit quand la température du corps dépasse de plusieurs degrés la
température normale du corps qui est de 98,6°F(37°C). Les symptômes d’hyperthermie
comprennent augmentation de la température du corps, vertige, léthargie, somnolence et
évanouissement. Les effets de l’hyperthermie comprennent l’incapacité de ressentir la chaleur,
l’incapacité de comprendre qu'il est nécessaire de sortir du spa ou du bain chaud, l'ignorance
du risque imminent, des dommages pour le foetus chez les femmes enceintes, l'incapacité
physique de sortir du spa ou du bain chaud et l'inconscience pouvant entraîner la noyade.
ATTENTION — La consommation d'alcool, de drogues ou de médicaments peut augmenter
considérablement le risque d'hyperthermie mortelle.
ATTENTION : LA TEMPÉRATURE DE L’EAU DÉPASSANT 100°F (38°C) PEUT ÊTRE
DANGEREUSE POUR VOTRE SANTÉ.
C. BOUTON DE CHAUFFAGE : utilisez ce bouton pour activer le
système de chauffage. Quand le voyant au-dessus du bouton du
chauffage est rouge, le système de chauffage est activé.
Quand le voyant est vert, l’eau se trouve à la température configurée et le
système de chauffage est à l’arrêt.
47
NETTOYAGE DU SPA
Les résidus de détergent et les matières dissoutes provenant des maillots de bain et
des produits chimiques peuvent s’accumuler sur les parois du spa. Utilisez du savon
et de l’eau pour nettoyer les parois et rincez bien.
REMARQUE : N’UTILISEZ PAS de brosses dures ni de produits d’entretien abrasifs.
Vérifiez que le spa et la pompe soient complètement secs. Ceci est fondamental
pour prolonger la durée de vie du spa. Nous vous recommandons d’utiliser la pompe
pour sécher le spa, la pompe et les tuyaux. Enlevez les kits de filtration et jetez les
cartouches de filtration usées. Placez à nouveau les deux bouchons d’obturation sur
les vannes d’entrée et de sortie du spa. Il est recommandé de ranger le spa dans
son emballage d’origine, au chaud [température supérieure à 59°F (15°C)] et au sec.
DÉGONFLAGE
Votre spa est équipé d’une fonction de dégonflage pour éliminer toute l’air qui se
trouve à l’intérieur de la chambre, afin de simplifier l’opération d’emballage et de
rangement.
RÉPARATION
Pour une pièce en PVC.
Si le spa est déchiré ou percé, réparez-le avec la rustine adhésive à utiliser sous l’eau fournie avec.
1. Nettoyez la zone à réparer.
2. Décollez soigneusement la rustine.
3. Appuyez la rustine sur la zone à réparer.
4. Attendez 30 secondes avant de le gonfler.
Pour le PVC TriTech.
Si le spa est déchiré ou percé, utilisez la rustine en PVC fournie avec et la colle (non fournie) en suivant ces étapes:
1. Nettoyez et séchez la zone à réparer.
2. Coupez la rustine en PVC fournie avec à la bonne taille.
3. Mettez la colle (non fournie) sur le côté de la rustine que vous venez de couper. Vérifiez que la colle soit distribuée uniformément.
4. Attendez 30 secondes avant de placer la rustine avec la colle sur la zone endommagée.
5. Lissez pour éliminer les bulles d’air qui pourraient s’être formées et appuyez dessus fermement pendant deux minutes.
6. Vous pouvez désormais utiliser à nouveau le produit. Répétez cette opération si vous découvrez d’autres fuites.
7. Attendez 30 minutes avant de le gonfler.
Soupape à vis
Valve de gonflage/dégonflage rapide
P61727ASS18
P61726ASS18
P05344
P61726ASS18
53

Specyfikacje produktu

Marka: Bestway
Kategoria: Niesklasyfikowane
Model: SaluSpa 60086

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bestway SaluSpa 60086, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Bestway

Bestway

Bestway 43644 Instrukcja

12 Stycznia 2025
Bestway

Bestway 58775 Instrukcja

25 Grudnia 2024
Bestway

Bestway 58767 Instrukcja

5 Października 2024
Bestway

Bestway 52646 Instrukcja

4 Października 2024
Bestway

Bestway 58764 Instrukcja

4 Października 2024
Bestway

Bestway SaluSpa 60024 Instrukcja

4 Października 2024
Bestway

Bestway 21096 Instrukcja

3 Października 2024
Bestway

Bestway Hydro-Force 65303 Instrukcja

24 Września 2024
Bestway

Bestway 25044 Instrukcja

23 Września 2024
Bestway

Bestway SaluSpa 60032 Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R14G Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R6RT Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
Shimbol

Shimbol Memory I PRO Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025