Instrukcja obsługi Benro HD2A

Benro statyw HD2A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Benro HD2A (2 stron) w kategorii statyw. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
HD Series 3-Way Panhead
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
1 2
Quick Release Plate
Horizontal Tilt Lock
Plate Locking Lever
Pan Lock
Base
Mounting Screw
Front/Rear Tilt Lock
Security Locking Lever
Bubble Level
SETUP
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
Three-way positioning of camera and
lens movement is directly controllable
on the HD Series 3-Way Panheads. Two
comfortable Handles provide both
movement and locking of front to rear
Tilt, and side to side Tilt. Plus, a separate
Locking Knob permits the entire Head
assembly to move freely within a 360°
rotational adjustment.
Quick Release Plate
The HD Series 3-Way Panheads incorporate
a Quick Release Plate system. It offers a
quick method of mounting or releasing a
Camera or Equipment from the Head. It’s
important that the correct Quick Release
Plate be used along with the proper
mounting screw (1/4–20 is included as the
standard size but spare 1/4–20 and 3/8
plates are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting and
dismounting gear.
Quick Release Locking Lever (FIGURES 1 & 2)
When used properly, the patented Dual
Lock Quick Release system offers two levels
of security for your gear. To remove the
Quick Release Plate, squeeze both the Plate
Locking Lever and the Security Locking
Lever and pull the larger Locking Lever
out. The Quick Release Plate will disengage
allowing it to be removed.
To reconnect the Quick Release Plate, insert
the angled part of the Plate into the groove
on the opposite side of the Locking Levers
and press down flat. The Locking Levers will
automatically engage the locking system and
will return to the safety lock position. Press
the Plate Locking Lever in firmly to secure.
Pan Control (FIGURE 3)
Horizontal rotation or Panning can be easily
accomplished by first loosening the Pan Lock
and then rotating Head on Platform. Once
in position tighten the Pan Lock securely.
NOTE: Do not over tighten the Pan Lock as
this could damage the locking mechanism.
Tilt Control (FIGURE 4)
Front to Rear Angle or Tilt adjustments can
be easily accomplished by first loosening
the Tilt Lock (be sure to hold on firmly to
balance weight of the camera). Position as
required and then tighten Handle securely.
You have the same Control and Lock
available on the other axis for Horizontal
Angle or Tilt adjustments.
NOTE: Do not over tighten the Tilt Locks as
this could damage the locking mechanism.
FOR ADDITIONAL CONTROL: Depending
on your requirements you may find it
convenient to reorient the camera or lens
90° on the Quick Release Plate and remount
so that the Tilt Controls give you different
positioning support.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Panhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any Panhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Panhead is not
recommended for use in salt water. If
required, clean Panhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Panhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
3 4
Operating Instructions & User Notice

Specyfikacje produktu

Marka: Benro
Kategoria: statyw
Model: HD2A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Benro HD2A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje statyw Benro

Benro

Benro ITrip FIT19AIH0 Instrukcja

8 Października 2024
Benro

Benro BV4PRO Instrukcja

2 Października 2024
Benro

Benro KH25N Instrukcja

20 Września 2024
Benro

Benro TSL08CN00 Instrukcja

2 Września 2024
Benro

Benro A2573FS6 Instrukcja

27 Sierpnia 2024
Benro

Benro FSL09AN00 Instrukcja

25 Sierpnia 2024
Benro

Benro A1883FS2C Instrukcja

20 Sierpnia 2024
Benro

Benro A373FBV4H Instrukcja

19 Sierpnia 2024
Benro

Benro BV4 Instrukcja

15 Sierpnia 2024
Benro

Benro FSL09CN00 Instrukcja

14 Sierpnia 2024

Instrukcje statyw

Najnowsze instrukcje dla statyw

Manfrotto

Manfrotto Digital Director Instrukcja

9 Października 2024
Manfrotto

Manfrotto MVR901ECEX Instrukcja

9 Października 2024
Manfrotto

Manfrotto 562B-1 Instrukcja

8 Października 2024
E-Image

E-Image EG01A2 Instrukcja

8 Października 2024
E-Image

E-Image GH10 Instrukcja

8 Października 2024
E-Image

E-Image GC752 Instrukcja

8 Października 2024
E-Image

E-Image EG03A2 Instrukcja

8 Października 2024
E-Image

E-Image GA752 Instrukcja

8 Października 2024
E-Image

E-Image GH03 Instrukcja

8 Października 2024
E-Image

E-Image GH06 Instrukcja

8 Października 2024