Instrukcja obsługi Benro BH00

Benro statyw BH00

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Benro BH00 (2 stron) w kategorii statyw. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
BH Series Single-Action Ballheads
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
Camera Screw
Quick Release Plate
Bubble Level
Base
Plate Locking Lever
Ball Locking Lever
Security
Locking Lever
Mounting Platform
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
The single-action Ball Locking Lever
controls all movements of the BH Series
Ballheads. When released, the Ballhead and
the Mounting Platform can move freely
within a 360° rotational adjustment. And
two U-shaped openings on opposite sides
provide 90° angular movement of the
Mounting Platform.
Quick Release Plate
The BH Series Single-Action Ballheads
incorporate a Quick Release Plate system.
It offers a quick method of mounting or
releasing a Camera or Equipment from the
Head. It’s important that the correct Quick
Release Plate be used along with the proper
mounting screw (1/4–20 is included as the
standard size but spare 1/4–20 and 3/8
plates are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting and
dismounting gear.
Quick Release Locking Lever
(FIGURES 1, 2 & 3)
When used properly, the patented Dual
Lock Quick Release system offers two levels
of security for your gear. To remove the
Quick Release Plate, squeeze both the Plate
Locking Lever and the Security Locking
Lever and pull the larger Locking Lever
out. The Quick Release Plate will disengage
allowing it to be removed.
To reconnect the Quick Release Plate, insert
the angled part of the Plate into the groove
on the opposite side of the Locking Levers
and press down flat. The Locking Levers will
automatically engage the locking system and
will return to the safety lock position. Press
the Plate Locking Lever in firmly to secure.
Ball Locking Lever (FIGURE 4)
The single-action Ball Locking Lever is
spring-loaded and can be repositioned when
it is in the lock position to accommodate
any desired Lever position. To reposition,
gently pull on the Lever to disengage, and
then allow the spring to pull the lever back
to reengage.
NOTE: Do not over tighten the Locking
Lever as this could damage the Ballhead
locking mechanism.
1 2
3
360°
180°
4
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Ballhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any ballhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Ballhead is not
recommended for use in salt water. If
required, clean Ballhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Ballhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
USER NOTICESETUP
Operating Instructions & User Notice

Specyfikacje produktu

Marka: Benro
Kategoria: statyw
Model: BH00

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Benro BH00, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje statyw Benro

Benro

Benro S4 Pro Instrukcja

8 Grudnia 2024
Benro

Benro S8Pro Instrukcja

8 Grudnia 2024
Benro

Benro S2Pro Instrukcja

8 Grudnia 2024
Benro

Benro ITrip FIT19AIH0 Instrukcja

8 Października 2024
Benro

Benro BV4PRO Instrukcja

2 Października 2024
Benro

Benro KH25N Instrukcja

20 Września 2024
Benro

Benro Video Monopod A48FDS4 Instrukcja

8 Września 2024
Benro

Benro HD3A Instrukcja

4 Września 2024
Benro

Benro Adventure Monopod MAD49A Instrukcja

3 Września 2024
Benro

Benro TSL08CN00 Instrukcja

2 Września 2024

Instrukcje statyw

Najnowsze instrukcje dla statyw

3 Legged Thing

3 Legged Thing Albert 2.0 Instrukcja

15 Stycznia 2025
3 Legged Thing

3 Legged Thing AirHed Pro Instrukcja

15 Stycznia 2025
3 Legged Thing

3 Legged Thing Leo 2.0 Instrukcja

15 Stycznia 2025
3 Legged Thing

3 Legged Thing Ray Instrukcja

15 Stycznia 2025
Pyle

Pyle PSTND25 Instrukcja

13 Stycznia 2025
Vinten

Vinten FlowTech 75 Instrukcja

11 Stycznia 2025
Manfrotto

Manfrotto MVTTWINMC Instrukcja

10 Stycznia 2025
Bauhn

Bauhn ABSS-1224 Instrukcja

8 Stycznia 2025
Auray

Auray GNCL-12 Instrukcja

4 Stycznia 2025
Auray

Auray GNCL-20 Instrukcja

4 Stycznia 2025