Instrukcja obsługi Beko WML 15040 KL

Beko pralka WML 15040 KL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Beko WML 15040 KL (48 stron) w kategorii pralka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
WML 15040 KL
WML 15050 KL
WML 15060 KL
WML 15060 E
WML 15080 DL
WML 15080 DB
WML 15080 P
WML 15100 P
WML 15100 DB
Washing Machine
Lavadora
Perilica rublja
Пералня машина
2 - EN
1 Warnings
General Safety
• Never place your machine on a
carpet covered floor. Otherwise, lack
of airflow from below of your machine
may cause electrical parts to
overheat. This may cause problems
with your washing machine.
• If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
• Fit the drain hose into the discharge
housing securely to prevent any
water leakage and to allow machine
to take in and discharge water as
required. It is very important that the
water intake and drain hoses are not
folded, squeezed, or broken when
the appliance is pushed into place
after it is installed or cleaned.
• Your washing machine is designed
to continue operating in the event of
a power interruption. Your machine
will not resume its program when
the power restores. Press the
“Start/Pause/Cancel” button for 3
seconds to cancel the program (See,
Canceling a Program)
• There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
• Some problems you may encounter
may be caused by the infrastructure.
Press “Start/Pause/Cancel” button
for 3 seconds to cancel the program
set in your machine before calling the
authorized service.
First Use
• Carry out your first washing process
without loading your machine and
with detergent under “Cottons 90°C”
program.
• Ensure that the cold and hot water
connections are made correctly when
installing your machine.
• If the current fuse or circuit breaker is
less than 16 Amperes, please have
a qualified electrician install a 16
Ampere fuse or circuit breaker.
• While using with or without a
transformer, do not neglect to have
the grounding installation laid by a
qualified electrician. Our company
shall not be liable for any damages
that may arise when the machine is
used on a line without grounding.
• Keep the packaging materials out
of reach of children or dispose them
by classifying according to waste
directives.
Intended use
• This product has been designed for
home use.
• The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
Safety instructions
• This appliance must be connected to
an earthed outlet protected by a fuse
of suitable capacity.
• The supply and draining hoses must
always be securely fastened and
remain in an undamaged state.
• Fit the draining hose to a washbasin
or bathtub securely before starting up
your machine. There may be a risk of
being scalded due to high washing
temperatures!
• Never open the loading door or
remove the filter while there is still
water in the drum.
• Unplug the machine when it is not in
use.
• Never wash down the appliance with
a water hose! There is the risk of
electric shock!
• Never touch the plug with wet hands.
Do not operate the machine if the
power cord or plug is damaged.
• For malfunctions that cannot be
solved by information in the operating
manual:
• Turn off the machine, unplug it,
turn off the water tap and contact
an authorized service agent. You
may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose
of your machine.
If there are children in your
house...
• Keep children away from the machine
when it is operating. Do not let them
tamper with the machine.
• Close the loading door when you
leave the area where the machine is
located.
3 - EN
2 Installation
Removing packaging
reinforcement
Tilt the machine to remove the packaging
reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Opening the transportation locks
A Transportation safety bolts must
be removed before operating the
washing machine! Otherwise, the
machine will be damaged!
1. Loosen all the bolts with a spanner
until they rotate freely (“C”)
2. Remove transportation safety bolts
by turning them gently.
3. Fit the covers (supplied in the bag
with the Operation Manual) into the
holes on the rear panel. (“P”)
C Keep the transportation safety bolts
in a safe place to reuse when the
washing machine needs to be moved
again in the future.
C Never move the appliance without
the transportation safety bolts
properly fixed in place!
Adjusting the feet
A Do not use any tools to loosen the
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
nuts on the feet.
2. Adjust them until the machine stands
level and firmly.
3. Important: Tighten all lock nuts up
again.
Connecting to the water supply.
Important:
• The water supply pressure required
to run the machine must be 1-10 bar
(0,1 – 1 MPa).
• Connect the special hoses supplied
with the machine to the water intake
valves on the machine.
• If you are going to use your double
water-inlet machine as a single (cold)
water-inlet unit, you must install the
stopper*, supplied with your machine
to the hot water valve.
• If you want to use both water inlets
of the product, you can connect the
hot water hose after removing the
stopper and gasket group from the
hot water valve.
* Applies for the products supplied with a
blind stopper group.
• Models with a single water inlet
should not be connected to the hot
water tap.
When returning the appliance to its place
after maintenance or cleaning, care should
be taken not to fold, squeeze or block the
hoses.
Connecting to the drain
The water discharge hose can be attached
to the edge of a washbasin or bathtub. The
drain hose should be firmly fitted into the
drain as to not get out of its housing.
Important:
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
• The hose should be attached to a
height of at least 40 cm, and 100 cm
at most.
• In case the hose is elevated after
laying it on the floor level or close
to the ground (less than 40 cm
above the ground), water discharge
becomes more difficult and the
laundry may come out wet.
• The hose should be pushed into the
drainage for more than 15 cm. If it is

Specyfikacje produktu

Marka: Beko
Kategoria: pralka
Model: WML 15040 KL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Beko WML 15040 KL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje pralka Beko

Beko

Beko B5W5941D Instrukcja

14 Października 2024
Beko

Beko BM1WU3741 Instrukcja

14 Października 2024
Beko

Beko B5W1241A Instrukcja

14 Października 2024
Beko

Beko BM3WT4841I Instrukcja

14 Października 2024
Beko

Beko B5W59411A Instrukcja

14 Października 2024
Beko

Beko B3W31041 Instrukcja

14 Października 2024
Beko

Beko BM3WT4104I Instrukcja

14 Października 2024
Beko

Beko BM3WT3841 Instrukcja

14 Października 2024
Beko

Beko B3W5941I Instrukcja

14 Października 2024
Beko

Beko BM1WT3721 Instrukcja

14 Października 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy

Candy CS 15102D3-80 Instrukcja

15 Października 2024
GE

GE GSD3715FAA Instrukcja

15 Października 2024
Siemens

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024
LG

LG WTP22BK Instrukcja

15 Października 2024
Freggia

Freggia WTIE148 Instrukcja

15 Października 2024
Freggia

Freggia WISE126R Instrukcja

15 Października 2024
Freggia

Freggia WISE126B Instrukcja

15 Października 2024
Freggia

Freggia WISE126 Instrukcja

15 Października 2024
Freggia

Freggia WISA105 Instrukcja

15 Października 2024
Freggia

Freggia WISA106 Instrukcja

15 Października 2024