Instrukcja obsługi BeamZ S2000 160.500
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BeamZ S2000 160.500 (16 stron) w kategorii My. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/16
1
S2000 Smokemachine DMX LED 24 x 3W
Ref. nr.: 160.500
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
GEBRAUCHSANLEITUNG
NOTICE D’UTIILSATION
V2.1
2
ENGLISH
Warning:
- The fog machine must be placed at least 100 cm away from inflammable materials such as curtains, books, etc. Make sure
that the housing cannot be touched by accident.
- Use only Beamz water-based fluid recommended by your dealer.
- Poor liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.
- Never add flammable fluids (oil, gas, perfume) to the fog liquid.
- Always keep enough liquid in the tank.
Use of the device without liquid will cause damage to the pump and heater.
- Do not obstruct the openings on top of the case to guarantee a good ventilation.
- objects on the fog machine Don’t put any .
- For indoor use only.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the fog machine.
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It needs to be
repaired by a qualified technician.
- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let the unit reach
room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a steel cable, etc.
which has to be fastened separately from the mounting bracket.
- The supplied bracket is the main fixing and must be used to solidly mount the light effect.
- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must be fulfilled.
- Keep out of the reach of children.
Location
Select a location where it is easy to fill the tank.
INSTALLATION AND USE
Safety
Plug the fog machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be replaced by an
original replacement, supplied by Tronios. Be careful when filling the fluid tank. First of all, unplug the mains lead! Then unscrew
the cap on the tank and fill it by means of a funnel.
Only use the original Beamz fluid which is environmental friendly and, if used correctly, leaves no residues.
Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke machine
generates heat which needs to be removed. Don’t put any objects on the smoke machine.
How to use
Unpack the f machine. Do not connect yet the net cable. Fill the fluid tank by means of a funnel. Plug the unit into a mains og
outlet. Thus the heating element is automatically switched on. Depending on the room temperature, it takes about 3 minutes
until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up. Push the
switch once and the f machine will produce a nice thick fog. Once the f machine has reached its working temperature (the og og
LED is lit) the f machine can produce fog continuously. After this period of time, the fog generator is cooled so much down og
that the thermostat switches off. Wait a while until the working temperature is reached again. It is recommended to produce
haze with small pauses in between so that the temperature is maintained and the thermostat doesn’t switch off.
Make sure that there is always enough liquid contained in the tank. Use of the f machi without liquid can permanently og ne
damage the unit. Once the f machine generates little haze or pump generate another 'rattling' sound turn off the unit direct. og
Check the fluid level and fill the tank when it is empty, check the hose and filter blockages and restore it. Plug in the unit and
check if the problem is resolved. If problem persists, switch unit direct off to prevent further damage and contact your dealer.
Switching the unit off
Switch the unit off by unplugging it from the mains. Otherwise the heating element will draw unnecessarily current.
3
Remote control:
SETTINGS
Via the Menu key, you can adjust the desired settings. After pressing the menu, the display shows the following settings:
1. Man Vol Out xxx%.
Adjust the manual volume output within the range of 0% to 100% by means of the Up/Down keys.
2. Interval Set xxxS
Adjust the interval between each fog emission within the range of 1 to 100S by means of the Up-/Down keys.
3. Duration Set xxxS
Adjust the duration of each fog emission within the range of 1 to 100S.
4. Volume Out xxx%
Adjust the volume output during the timer function within the range of 0- 100%
5. DMX 512 #xxx
Adjust the DMX address for DMX control.
6. Wind For Class xx
NO FUNCTION for this smoke machine
7. Angel Set xx%
NO FUNCTION for this smoke machine
8. LED Pro Set xx
Adjust the LED program within the range of 0 to 11.
9. LED Spe xxx
Adjust the LED speed/strobe/fade of the LED program mode
10. Temper Max:xxx
Adjust the maximum heating temperature of the heating element, adjustable between 285° - 330°C.
11. LED Sync Set Yes/No
Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on.
12. Temper Min:xxx
Adjust the minimum heating temperature of the heating element, adjustable between 260° - 310°C.
TIMER CONTROL
Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds
down to "0". After that, the fog emission is triggered at the volume adjusted under "Timer Out". The duration depends on the
settings adjusted under "Duration Set". If you wish to deactivate the timer function, press the Timer key once more.
Manual control (100% output)
Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key
loose in order to stop the fog emission.
Manual control (locked)
Press the Lock switch for immediate triggering of the fog emission at the volume adjusted under "Volume Out". Press the
Volume switch once more in order to stop the fog emission.
DMX control
Connect the machine directly to a DMX controller or a DMX loop with multiple DMX effects. The machine uses a 3-pin XLR
connector for DMX connection.
Address Setup: Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons the
start address may be set. The start address is defined as a first channel to which the machine will respond to. Check that there
are no overlapping channels used!
Specyfikacje produktu
| Marka: | BeamZ |
| Kategoria: | My |
| Model: | S2000 160.500 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BeamZ S2000 160.500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje My BeamZ
2 Października 2024
27 Sierpnia 2024
26 Sierpnia 2024
6 Lipca 2024
6 Lipca 2024
5 Lipca 2024
5 Lipca 2024
4 Lipca 2024
Instrukcje My
- My Ikea
- My Livoo
- My SilverCrest
- My Brentwood
- My Toolcraft
- My Black & Decker
- My Hazet
- My RYOBI
- My Cuisinart
- My Crivit
- My Fagor
- My Steba
- My TriStar
- My Exquisit
- My Gastroback
- My G3 Ferrari
- My Hamilton Beach
- My Hama
- My Waring Commercial
- My Kalorik
- My HQ Power
- My Oster
- My Fritel
- My Victorinox
- My Ernesto
- My Team
- My Wolf
- My Girmi
- My Underwater Kinetics
Najnowsze instrukcje dla My
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
7 Października 2024
6 Października 2024
5 Października 2024
4 Października 2024
3 Października 2024