Instrukcja obsługi BeamZ H2000 160.512

BeamZ Maszyna efektów H2000 160.512

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BeamZ H2000 160.512 (20 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

H2000 Fazer DMX LCD

Ref. nr.: 160.512

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

GEBRAUCHSANLEITUNG

MANUEL D'INSTRUCTIONS

V1.4

ENGLISH

Warning:

- The fazer machine must be placed at least 100 cm away from inflammable materials such as curtains, books, etc. Make

sure that the housing cannot be touched by accident.

- Use only Beamz water-based fluid recommended by your dealer.

- Poor liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.

- Never add flammable fluids (oil, gas, perfume) to the fog liquid.

- Always keep enough liquid in the tank.

Use of the device without liquid will cause damage to the pump and heater.

- Do not obstruct the openings on top of the case to guarantee a good ventilation.

- Don’t put any objects on the fazer machine.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the first use, have the unit checked by a qualified person.

- The unit contains voltage carrying parts. DO NOT open the fazer machine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It needs to be

repaired by a qualified technician.

- Only connect this unit to an earthed mains outlet of 220-240Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let the unit reach

room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a steel cable, etc.

which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main fixing and must be used to solidly mount the light effect.

- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must be fulfilled.

- Keep out of the reach of children.

Location

Select a location where it is easy to fill the tank.

INSTALLATION AND USE

Safety

Plug the fazer machine only in an earthed mains outlet or extension cord! ATTENTION: the power cord can only be replaced by

an original replacement, supplied by Tronios.

Be careful when filling the fluid tank. First of all, unplug the mains lead! Then unscrew the cap on the tank and fill it by means of

a funnel.

Only use the original Beamz fluid which is environmental friendly and, if used correctly, leaves no residues.

Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke machine

generates heat which needs to be removed. Don’t put any objects on the smoke machine.

How to use

Unpack the fazer machine. Do not connect yet the net cable. Fill the fluid tank by means of a funnel. Plug the unit into a mains

outlet. Thus the heating element is automatically switched on. Depending on the room temperature, it takes about 3 minutes

until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up. Push the

switch once and the fazer machine will produce a nice thick fog. Once the fazer machine has reached its working temperature

(the LED is lit) the fazer machine can produc time, the fog generator is cooled so muche fog continuously. After this period of

down that the thermostat switches off. ain. It is recommended to Wait a while until the working temperature is reached ag

produce haze with small pauses in between so that the temperature is maintained and the thermostat doesn’t switch off.

Make sure that there is always enough liquid contained in the without liquid can permanently tank. Use of the fazer machine

damage the unit. Once the fazer machine generates little haze or pump generate another 'rattling' sound turn off the unit direct.

Check the fluid level and fill the tank when it is empty, check the hose and filter blockages and restore it. Plug in the unit and

check if the problem is resolved. If problem persists, switch unit direct off to prevent further damage and contact your dealer.

Switching the unit off

Switch the unit off by unplugging it from the mains. Otherwise the heating element will draw unnecessarily current.

Specyfikacje produktu

Marka:	BeamZ
Kategoria:	Maszyna efektów
Model:	H2000 160.512

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z BeamZ H2000 160.512, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna efektów BeamZ

BeamZ PS6W 151.262 Instrukcja

14 Stycznia 2025

BeamZ S553L Instrukcja

5 Stycznia 2025

BeamZ BLAZE3500 Instrukcja

8 Października 2024

BeamZ SparkleWall 151.201 Instrukcja

8 Października 2024

BeamZ BLAZE1200 Instrukcja

7 Października 2024

BeamZ BLAZE800 Instrukcja

7 Października 2024

BeamZ ICE700 Instrukcja

7 Października 2024

BeamZ BLAZE1800 Instrukcja

7 Października 2024

BeamZ LUCID 1.2 150.462 Instrukcja

2 Października 2024

BeamZ Mini 153.325 Instrukcja

30 Września 2024

Instrukcje Maszyna efektów

Najnowsze instrukcje dla Maszyna efektów

Audibax Smoke 500 Instrukcja

5 Stycznia 2025

Audibax Haze 1200 Instrukcja

5 Stycznia 2025

Audibax Smoke 1500 Instrukcja

5 Stycznia 2025

Audibax VOLCANO 1500 RGBW Instrukcja

5 Stycznia 2025

Audibax Spark 600 Instrukcja

5 Stycznia 2025

Audibax Smoke 700 LED Instrukcja

5 Stycznia 2025

Audibax Smoke 1200 Instrukcja

5 Stycznia 2025

Audibax Geyser 2000 Instrukcja

5 Stycznia 2025

Westinghouse W24V5AH Instrukcja

3 Stycznia 2025

Westinghouse WSnow11S Instrukcja

3 Stycznia 2025