Instrukcja obsługi BeamZ Apollo
BeamZ
Maszyna efektów
Apollo
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BeamZ Apollo (17 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/17
Multipoint Laser G-50mW R-80mW
Ref. Nr. 152.752
V2.1
Instruction Manual
Gebruiksaanwijzing
Mode d’Emploi
Gebrauchsanleitung
2 — —
User’s manual
Thanks for your purchasing, please read this manual carefully before operating the system. It gives you general information
for your safe and better operation.
Installation
Firstly, be sure that the using voltage is match with the
voltage marked on the base of the laser;
Installation should be made by professional technician.
fix the laser lighting and adjust the angle of the moving
head to you need;
Be sure that there is no flammable or explosive subject
nearby. The least distance is 0.5 meters. at the same
time, keep more than 15cm between the wall and laser
lighting;
Please check whether the fan and the exhaust is blocked;
There is a hole for connection. when hang the laser lighting,
be sure the cable can undertake 10 times of the lighting
weight;
The laser lighting should be fixed;
It is essential to be earthed well for the sake of safety.
WARNING DATA
Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are
used incorrectly. Pay close attention to each safety REMARK and WARNING statement in the user manual. Read all
instructions carefully BEFORE operating this device.
Indicates a skill or other useful information for special situations.
Indicates important information to protect personnel from laser incident or injury.
Prevent damage or injury from incorrect operation.
Laser safety warming labels.
To protect the environment, recycle packing material wherever possible.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and
moisture, excessive heat, humidity and dust. Do not allow contact with water or other fluids.
Don’t throw this product away just as general trash, please dispose of this product following the abandon
electronic product regulations in your area.
The projector must be installed in a location with adequate ventilation, at least 50cm (20 inches) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Avoid direct eye contact with laser light. Never
intentionally expose your eyes or others to direct laser
light..
This laser product can potentially cause instant eye
injury or blindness if laser light directly strikes the eyes.
It is illegal and dangerous to shine this laser into
audience areas, where the audience or other personnel
could get direct laser beams or bright reflections into
their eyes.
It is an offense to shine any laser at aircraft.
There are no user serviceable parts inside the unit. Do
not open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please
contact the dealer nearest to you..
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
NON-INTERLOCKED HOUSING WARNING
This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser
radiation. The laser power levels accessible if the unit is opened can cause instant blindness, skin burns and fires.
3 — —
LASER SAFETY AND OPERATING INSTRUCTIONS
STOP AND READ ALL LASER SAFETY DATA
Laser Light is different from any other light source with which you may be familiar. The light from this product can potentially
cause eye injury if not set up and used properly. Laser light is thousands of times more concentrated than light from any other
kind of light source. This concentration of light power can cause instant eye injuries, primarily by burning the retina (the light
sensitive portion at the back of the eye). from a laser beam, it can still potentially injure or blind Even if you cannot feel “heat”
you or your audience. Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye
injuries can happen quicker than you can blink. It is incorrect to think that because these laser entertainment products split
the laser into hundreds of beams or laser beam is scanned out in high speed, that an individual laser beam is safe for eye
exposure. This laser product uses dozens of mini Watts of laser power (Class 3B levels internally). Many of the individual
beams are potentially hazardous to the eyes. It is also incorrect to assume that because the laser light is moving, it is safe.
This is not true. Nor, do the laser beams always move. Since eye injuries can occur instantly, it is critical to prevent the
possibility of any direct eye exposure. In the laser safety regulation, it is not legal to aim Class 3B lasers in areas which
people can get exposed. This is true even if it is aimed below people’s faces, such as on a dance floor.
Do not operate laser without first reading and
understanding all safety and technical data in this
manual
Always set up and install all laser effects so that all
laser light is at least 3 meters (9.8 feet) above the
floor on which people can stand. See “Proper Laser
Set- up & Usage” section later in this manual
After set up, and prior to public use test laser to ensure
proper function. Do not use if any defect is detected. Do
not use if laser emits only one or two laser beams rather
than dozens/hundreds, as this could indicate damage
to the diffraction grating optic, and could allow emission
of higher laser levels.
Do not point lasers at people or animals
Never look into the laser aperture or laser beams
Do not point lasers in areas in which people can
potentially get exposed, such as uncontrolled balconies,
etc.
Do not point lasers at highly reflective surfaces such as
windows, mirrors and shiny metal. Even laser
reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense
Never point un-terminated laser beams into the sky
Do not expose the output optic (aperture) to cleaning
chemicals
Do not use laser if the laser appears to be emitting only
one or two beams
Do not use laser if housing is damaged or open, or if
optics appear damaged in any way.
Never open the laser housing. The high laser power
levels inside of the protective housing can start fires,
burn skin and will cause instant eye injury.
Never leave this device running unattended.
The operation of a class 3B laser show laser is only
allowed if the show is controlled by a skilled and
well-trained operator familiar with the data included in
this manual.
The legal requirements for using laser entertainment
products vary from country to country. The user is
responsible for the legal requirements at the
location/country of use.
Always use appropriate lighting safety cables when
hanging lights and effects overhead
Power off before installation or maintenance
The danger class of this laser lighting is CLASS IIIB.
It’s dangerous for observing laser. The safe minimum
distance is 13cm,the safe maximum time is 10 seconds
Keep at least 0.5 meters distance between the lighting
and flammable material
LASER SAFETY LABEL REPRODUCTIONS
Caution Class LASER RADIATION, WHEN OPEN, AVOID EXPOSURE TO BEAM –3B
LASER RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT.
The label indicates the laser beam output aperture.
Specyfikacje produktu
| Marka: | BeamZ |
| Kategoria: | Maszyna efektów |
| Model: | Apollo |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BeamZ Apollo, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna efektów BeamZ
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
2 Października 2024
30 Września 2024
29 Września 2024
27 Września 2024
Instrukcje Maszyna efektów
- Maszyna efektów Behringer
- Maszyna efektów American DJ
- Maszyna efektów Chauvet
- Maszyna efektów Antari
- Maszyna efektów Eurolite
- Maszyna efektów Velleman
- Maszyna efektów Manta
- Maszyna efektów Showtec
- Maszyna efektów Klark Teknik
- Maszyna efektów Doepfer
- Maszyna efektów Cameo
- Maszyna efektów Lotronic
- Maszyna efektów Elation
- Maszyna efektów Futurelight
- Maszyna efektów Martin
- Maszyna efektów HQ Power
- Maszyna efektów Magmatic
- Maszyna efektów Technical Pro
- Maszyna efektów Adj
- Maszyna efektów Steren
- Maszyna efektów Valcom
- Maszyna efektów QTX
- Maszyna efektów Valueline
- Maszyna efektów Fredenstein
- Maszyna efektów Monoprice
- Maszyna efektów ColorKey
- Maszyna efektów Laserworld
- Maszyna efektów JB Systems
- Maszyna efektów Evo-Lite
- Maszyna efektów Blizzard
- Maszyna efektów Hazebase
- Maszyna efektów Fun Generation
- Maszyna efektów IMG Stage Line
- Maszyna efektów Lexicon
- Maszyna efektów The Confetti Maker
- Maszyna efektów BoomTone DJ
- Maszyna efektów TCM FX
Najnowsze instrukcje dla Maszyna efektów
10 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024