Instrukcja obsługi Baby Lock Crafters Choice BLCC2

Baby Lock maszyna do szycia Crafters Choice BLCC2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Baby Lock Crafters Choice BLCC2 (112 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 26 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/112
CONGRATULATIONS ON CHOOSING
OUR MACHINE
Your machine is the most advanced computerized household sewing machine.
To fully enjoy all the features incorporated, we suggest that you study the manual.
PLEASE READ BEFORE USING THIS MACHINE
For safe operation
1. Be sure to keep your eye on the needle while sewing. Do not touch the handwheel, thread take-
up lever, needle, or other moving parts.
2. Remember to turn off the power switch and unplug the cord when:
• Operation is completed
• Replacing or removing the needle or any other parts
• A power failure occurs during use
• Maintaining the machine
• Leaving the machine unattended.
3. Do not store anything on the foot controller.
4. Plug the machine directly into the wall. Do not use extension cords.
For a longer service life
1. When storing this machine, avoid direct sunlight and high humidity locations. Do not use or
store the machine near a space heater, iron, halogen lamp, or other hot objects.
2. Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders
can damage the case and machine, and should never be used.
3. Do not drop or hit the machine.
4. Always consult the operation manual when replacing or installing any assemblies, the presser
feet, needle, or other parts to assure correct installation.
For repair or adjustment
In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in
the back of the operation manual to inspect and adjust the machine yourself. If the problem persists,
please consult your local authorized Baby Lock retailer.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information and updates, visit our web site at www.babylock.com
1
Important Safety Instructions
Please read these safety instructions before attempting to use the machine.
This machine is intended for household use.
DANGER - To reduce the risk of electric shock:
1Always unplug the machine from the electrical outlet immediately after using, when cleaning,
when making any user servicing adjustments mentioned in this manual, or if you are leaving the
machine unattended.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons.
2Always unplug the machine from the electrical outlet when removing covers, lubricating, or
when making any adjustments mentioned in the instruction manual:
• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp
the plug and pull it out of the electrical outlet. Do not pull on the cord.
• Plug the machine directly into the electrical outlet. Do not use an extension cord.
•Always unplug your machine if the power is cut.
3Never operate this machine if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest
authorized retailer or service center for examination, repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything unusual, such as an odor, heat,
discoloration or deformation, stop using the machine and immediately unplug the power cord.
4Always keep your work area clear:
• Never operate the machine with any air openings blocked. Keep ventilation openings of the
sewing machine and foot control free from the build up of lint, dust, and loose cloth.
•Do not store objects on the foot controller.
•Do not use extension cords. Plug the machine directly into the electrical outlet.
•Never drop or insert any object into any opening.
•Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
•Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine,
power cord or garment being sewn may ignite, resulting in fire or an electric shock.
8
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
■Attaching the stitch pattern plate
The stitch pattern plate shows the stitches and the stitch numbers. A letter (A, G, J, N or R) indicating the presser
foot that should be used appears below the stitch number. Attach the stitch pattern plate to the handle as shown
in the illustration below.
Optional accessories
The following are available as optional accessories.
Memo
●Visit your Baby Lock retailer for a complete listing of optional accessories available for your machine.
1. 2. 3.
4. 5. 6. 7.
8. 9 11.10. .
No. Part Name Part Code No. Part Name Part Code
1 Side cutter FA10 7 Non stick foot FA8
2 Quilting guide FA11 8 Open toe foot FA7
3 Extension table BLR-ET 9 Stitch guide foot “P” FA6
4 Walking foot BLG-WI 10 1/4 inch quilting foot FA1
5 Quilting foot FA2 11 1/4 inch quilting foot with
guide ESG-QGF
6 Adjustable zipper/piping foot FA9
12
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Operation panel
The operation panel, located on the front at the right of the sewing machine, consists of various buttons and
sliders for specifying how the stitch will be sewn.
1 2Stitch width adjustment slider / Stitch width adjustment button
These are used to adjust the width of the stitch or the needle position. After pressing the stitch width adjustment button, use
the stitch width adjustment slider to adjust the stitch width.
3 4Stitch length adjustment slider / Stitch length adjustment button
These are used to adjust the length of the stitch. After pressing the stitch length adjustment button, use the stitch length
adjustment slider to adjust the stitch length.
5Needle mode selection key (single/twin)
Press the needle mode selection key to select the twin needle sewing setting. Each time this key is pressed, the setting
switches between that for single needle sewing and for twin needle sewing.
6Needle stop position key
This is used to change the position of the needle when the sewing machine is stopped. If the key is lit, the sewing machine
will stop with the needle raised. If the key is not lit, the sewing machine will stop with the needle lowered.
7Automatic reverse/reinforcement stitch key
Press the automatic reverse/reinforcement stitch key to automatically sew reverse or reinforcement stitches at the
beginning and end of stitching.
8Stitch selection key
Press the stitch selection key to select the number for the stitch that you wish to use. 80 stitches are available. For details,
refer to “Selecting Stitching” (page 56).
9Stitch indicator
This displays the number, width and length of the currently selected stitch. Press the stitch number display key (0), stitch
width display key (A) or the stitch length display key (B) to display the corresponding information. In addition, error
messages for incorrect operation appear in the stitch indicator.
0Stitch number display key
Press the stitch number display key to display the number of the currently selected stitch. When the stitch number is
displayed, the stitch number display key lights up.
AStitch width display key
Press the stitch width display key to display the width of the currently selected stitch. When the stitch width is displayed,
the stitch width display key lights up.
BStitch length display key
Press the stitch length display key to display the length of the currently selected stitch. When the stitch length is displayed,
the stitch length display key lights up.
10
3
4
2
5
6
7
8
9
A
B
14
GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Turning the Machine On/Off
This section explains how to turn the sewing machine on and off.
Power supply precautions
Be sure to observe the following precautions concerning the power supply.
●Use only regular household electricity for the power source. Using other power sources may
result in fire, electric shock, or damage to the machine.
• Make sure that the plugs on the power cord are firmly inserted into the electrical outlet
and the power supply jack on the machine.
• Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
●Turn off the main power and remove the plug in the following circumstances:
• When you are away from the machine
• After using the machine
• When the power fails during use
• When the machine does not operate correctly due to a bad connection or a disconnection
• During electrical storms
●Use only the power cord included with this machine.
●Do not use extension cords or multi-plug adapters with many other appliances plugged in to
them. Fire or electric shock may result.
●Do not touch the plug with wet hands. Electric shock may result.
●When unplugging the machine, always turn off the main power first. Always grasp the plug to
remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric
shock.
●Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted,
or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These
things may damage the cord and cause fire or electric shock. If the cord or plug is damaged,
take the machine to your authorized retailer for repairs before continuing use.
●Unplug the power cord if the machine is not to be used for a long period of time. Otherwise a
fire may result.
WARNING
CAUTION
16
GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Winding/Installing the Bobbin
This section describes how to wind the thread onto the bobbin, and then insert the bobbin thread.
Bobbin precautions
Be sure to observe the following precautions concerning the bobbin.
Winding the bobbin
Wind the thread around the bobbin to prepare the bobbin thread.
1Bobbin winder
Memo
●The order that the machine should be threaded for winding the bobbin is indicated by a broken line on
the sewing machine. Be sure to thread the machine as indicated.
●Only use the bobbin (part code: X52800-150) designed specifically for this sewing machine.
Use of any other bobbin may result in injuries or damage to the machine.
●The included bobbin was designed specifically for this sewing machine. If bobbins from other
models are used, the machine will not operate correctly. Use only the included bobbin or
bobbins of the same type (part code: X52800-150).
CAUTION
Actual size
This model Other model
11.5 mm
(7/16 inch)
1
Upper Threading 25
1
Threading the needle
This section describes how to thread the needle.
Note
● The needle threader can be used with
sewing machine needles 75/11 through
100/16.
● Thread with a thickness of 130/20 or thicker
cannot be used with the needle threader.
● The needle threader cannot be used with
the wing needle or the twin needle.
● If the needle threader cannot be used, refer
to “Threading the needle manually (without
using the needle threader)” (page 26).
1Pull the end of the thread passed through the
needle bar thread guide to the left, and then
pass the thread through the thread guide disk
from the front.
1 Thread guide disk
2Cut the thread with the cutter on the left side
of the machine.
1 Cutter
Note
● If the thread is pulled through and cannot
be cut correctly, lower the presser foot so
that the thread is held in place before
cutting the thread. If this operation is
performed, skip step 3.
●
When using thread that quickly winds off the
spool, such as metallic thread, it may be
difficult to thread the needle if the thread is cut.
Therefore, instead of using the thread cutter,
pull out about 80 mm (approx. 3 inches) of
thread after passing it through the thread
guide disks (marked “7”).
1 80 mm (3 inches) or more
3Lower the presser foot lever to lower the
presser foot.
1 Presser foot lever
4Lower the needle threader lever on the left
side of the machine until it clicks, and then
slowly return the lever to its original position.
1 Needle threader lever
XThe thread is passed through the eye of the
needle.
1
1
1
1
1
Upper Threading 29
1
Pulling up the bobbin thread
When making gathers or before free-motion quilting,
first pull up the bobbin thread as described below.
1Insert the bobbin into the bobbin case.
• Refer to steps 1 5 through of “Installing the
bobbin” (page 20).
2Pass the bobbin thread through the slot.
Do not cut the thread with the cutter.
3While lightly holding the upper thread with
your left hand with the needle in the up-
position, press (“Needle Position”
button) twice to lower and raise the needle.
1“Needle Position” button
XThe bobbin thread is looped around the
upper thread and can be pulled up.
4Carefully pull the upper thread upward to pull
out the end of the bobbin thread.
5Pull out about 10-15 cm (4-5 inches) of the
bobbin thread under the presser foot toward
the rear of the machine.
6Reattach the bobbin cover.
Insert the tab in the lower-left corner of the
bobbin cover, and then lightly press down on
the right side.
1
1
2
30
GETTING READY — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Replacing the Needle
This section provides information on sewing machine needles.
Needle precautions
Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these
precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to
read and carefully follow the instructions below.
Needle types and their uses
The sewing machine needle that should be used depends on the fabric and thread thickness. Refer to the
following table when choosing the thread and needle appropriate for the fabric that you wish to sew.
●Only use home sewing machine needles. Use of any other needle may bend the needle or
damage the machine.
●Never use bent needles. Bent needles can easily break, possibly resulting in injuries.
CAUTION
Fabric Type/Application Thread Size of Needle
Type Weight
Medium
weight
fabrics
Broadcloth Cotton thread 60 80–
75/11–90/14
Taffeta Synthetic thread
Flannel,
Gabardine Silk thread 50
Thin
fabrics
Lawn Cotton thread 60 80–
65/9–75/11Georgette Synthetic thread
Challis, Satin Silk thread 50
Thick
fabrics
Denim Cotton thread 30–50
90/14–100/16
Corduroy Synthetic thread 50
Tweed Silk thread
Stretch
fabrics
Jersey Thread for knits 50–60
Ball point needle
(golden colored)
75/11–90/14
Tricot
Easily frayed fabrics
Cotton thread 50 80–
65/9–90/14Synthetic thread
Silk thread 50
For top-stitching Synthetic thread 30 90/14–100/16
Silk thread
Replacing the Needle 31
1
Memo
●The smaller the thread number, the thicker
the thread, and the larger the needle
number, the thicker the needle.
●Use the ball point needle when sewing on
stretch fabrics or fabrics where skipped
stitches easily occur.
●Use a 90/14 to 100/16 needle with
transparent nylon threads, regardless of the
fabric being sewn.
●A 75/11 needle is already installed when
the sewing machine is purchased.
Checking the needle
Sewing with a bent needle is extremely dangerous
since the needle may break while the machine is
being operated.
Before using the needle, place the flat side of the
needle on a flat surface and check that the distance
between the needle and the flat surface is even.
1Flat side
2Needle type marking
■Correct needle
1Flat surface
■Incorrect needle
If the distance between the needle and the flat
surface is not even, the needle is bent. Do not use
a bent needle.
1Flat surface
●The appropriate fabric, thread and
needle combinations are shown in the
table on page 30. If the combination of
the fabric, thread and needle is not
correct, particularly when sewing thick
fabrics (such as denim) with thin needles
(such as 65/9 to 75/11), the needle may
bend or break. In addition, the stitching
may be uneven or puckered or there may
be skipped stitches.
CAUTION
1
2
1
1
40
SEWING BASICS — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Sewing
Basic sewing operations are described below.
Before operating the sewing machine, read the following precautions.
General sewing procedure
Follow the basic procedures below to sew.
●While the machine is in operation, pay special attention to the needle location. In addition,
keep your hands away from all moving parts such as the needle and handwheel, otherwise
injuries may occur.
●Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the
needle may break.
●Never use bent needles. Bent needles can easily break, possibly resulting in injuries.
●Make sure that the needle does not strike basting pins, otherwise the needle may break or
bend.
1Turn on the
machine.
Turn on the sewing machine.
For details on turning on the machine, refer to “Turning on the machine”
(page 15).
↓
2 Select the stitch. Select the stitch appropriate for the area to be sewn.
For details on selecting a stitch, refer to “Selecting stitching” (page 56).
↓
3Attach the presser
foot.
Attach the presser foot appropriate for the stitch.
For details on replacing the presser foot, refer to “Replacing the presser
foot” (page 33).
↓
4 Position the fabric.
Place the area to be sewn under the presser foot. Be sure that the fabric
pieces are sewn in the correct order and that the right and wrong sides of
the fabric are aligned correctly.
For details on positioning the fabric, refer to “Positioning the fabric”
(page 41).
↓
5 Start sewing. Start sewing.
For details on starting to sew, refer to “Starting to sew” (page 42).
↓
6 Cut the thread. Cut the thread at the end of sewing.
For details on cutting the thread, refer to “Cutting the thread” (page 45).
CAUTION
Sewing 43
2
3Turn on the sewing machine.
4Slide the sewing speed controller to the left or
right to select the desired sewing speed.
Slide the sewing speed controller to the left to
sew at a slower speed, or slide the speed
controller to the right to sew at a faster speed.
1 Sewing speed controller
• The speed set using the sewing speed
controller will be the foot controller’s
maximum sewing speed.
5Once you are ready to start sewing, slowly
press down on the foot controller.
Pressing down on the foot controller increases
the sewing speed; releasing the pressure on the
foot controller decreases the sewing speed.
• Slowly press down on the foot controller.
Pressing it down hard starts sewing too quickly.
XThe machine starts sewing.
6When the end of the stitching is reached,
completely release the foot controller.
XThe machine stops sewing with the needle
lowered (in the fabric).
7When you are finished sewing, raise the
needle, and then cut the threads.
• For details, refer to “Cutting the thread”
(page 45).
Memo
● If (Needle stop position key) is lit, the
sewing machine will stop with the needle
raised. If the key is not lit, the sewing
machine will stop with the needle lowered.
The needle position setting selected with
the needle stop position key does not
change if the sewing machine is turned off.
● When the foot controller is plugged in,
/ (“Start/Stop” button) cannot be
used to start or stop sewing.
1
Slower
Faster
●Do not allow thread or dust to accumulate
in the foot controller, otherwise a fire or
an electric shock may occur.
●
Do not place objects on the foot controller,
otherwise damage to the machine or
injuries may occur.
●If the machine is not to be used for a long
period of time, unplug the foot controller,
otherwise a fire or an electric shock may
occur.
CAUTION
Adjusting the Stitch Width and Length 47
2
Adjusting the Stitch Width and Length
The zigzag width (pattern width) and stitch length of utility stitches can be adjusted. Normally, when a stitch is
selected, the appropriate width and length are automatically selected. For details on the range of values within
which the width and length can be set, refer to “Stitch Settings” (page 94).
Adjusting the stitch width
The stitch width (zigzag width) can be adjusted to
make the stitch wider or narrower.
Note
● When (Stitch width display key) is
pressed, the currently specified stitch width
(needle position for the straight stitch (left
needle position) or triple stretch stitch)
appears in the stitch indicator. This allows
the specified setting to be checked while it
is being changed.
1 Stitch width display key
When the stitch width is displayed, stitch
width display key lights up.
1Press the stitch width adjustment button in
the operation panel.
XThe stitch width adjustment button lights up.
2Slide the stitch width adjustment slider up and
down.
Sliding the stitch width adjustment slider up
makes the stitch width wider; sliding the slider
down makes the stitch width narrower.
1 Stitch width adjustment slider
2 Stitch width adjustment button
■ Changing the needle position
With the straight stitch (left needle position) and
the triple stretch stitch, the needle position can be
adjusted. Sliding the stitch width adjustment
slider up moves the needle to the right; sliding the
slider down moves the needle to the left.
• To automatically select the stitch width most
appropriate for the selected stitch, press the
stitch width adjustment button again.
1
1
2
●After adjusting the stitch width, slowly
turn the handwheel toward you and
check that the needle does not touch the
presser foot. If the needle hits the presser
foot, the needle may bend or break.
CAUTION
3 UTILITY STITCHES
The various stitches and their applications are described in this chapter.
Selecting Stitching...................................................................................................56
Selecting stitching ..............................................................................................56
Overcasting Stitches................................................................................................58
Sewing overcasting stitches using overcasting foot “G”.....................................58
Sewing overcasting stitches using zigzag foot “J” ..............................................59
Sewing overcasting stitches using the optional side cutter .................................60
Basic Stitching.........................................................................................................62
Basic stitching ....................................................................................................62
Blind Hem Stitching ................................................................................................63
Buttonhole Stitching/Button Sewing .......................................................................65
Buttonhole sewing..............................................................................................66
Button sewing ....................................................................................................69
Zipper Insertion ......................................................................................................72
Inserting a centered zipper ................................................................................72
Inserting a side zipper ........................................................................................73
Sewing Stretch Fabrics and Elastic Tape..................................................................76
Stretch stitching .................................................................................................76
Elastic attaching ................................................................................................. 76
Appliqué, Patchwork and Quilt Stitching ................................................................78
Appliqué stitching ..............................................................................................79
Patchwork (crazy quilt) stitching .......................................................................80
Piecing ...............................................................................................................80
Quilting..............................................................................................................81
Free-motion quilting...........................................................................................82
Reinforcement Stitching ..........................................................................................83
Triple stretch stitching .......................................................................................83
Bar tack stitching ...............................................................................................83
Eyelet Stitching........................................................................................................85
Decorative Stitching................................................................................................86
Fagoting .............................................................................................................87
Scallop stitching.................................................................................................88
Smocking............................................................................................................88
Joining................................................................................................................89
Heirloom stitching .............................................................................................90
58
UTILITY STITCHES — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Overcasting Stitches
Sew overcasting stitches along the edges of cut fabric to prevent fabric from fraying. Seven stitches are available for
overcasting. The procedure for sewing overcasting stitch is explained according to the presser foot that is used.
Sewing overcasting stitches using overcasting foot “G”
Three stitches can be used to sew overcasting with overcasting foot “G”.
1Attach overcasting foot “G”.
• For details, refer to “Replacing the presser
foot” (page 33).
2Select a stitch.
• For details, refer to “Selecting stitching”
(page 56).
3Position the fabric with the edge of the fabric
against the guide of the presser foot, and then
lower the presser foot lever.
1Guide
4Sew with the edge of the fabric against the
presser foot guide.
1Needle drop point
Stitch Name Pattern Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)] Presser
Foot
Auto Manual Auto Manual
Overcasting
stitch
06 Preventing fraying in medium
weight and thin fabrics 3.5
(1/8) 2.5–5.0
(3/32–3/16) 2.0
(1/16) 1.0–4.0
(1/16–3/16)
G
07
Preventing fraying in thick fabrics
and fabrics that fray easily
5.0
(3/16) 2.5–5.0
(3/32–3/16) 2.5
(3/32) 1.0–4.0
(1/16–3/16)
08 5.0
(3/16) 3.5–5.0
(1/8–3/16) 2.5
(3/32) 1.0–4.0
(1/16–3/16)
G
a
●After adjusting the stitch width, slowly
turn the handwheel toward you
(counterclockwise) and check that the
needle does not touch the presser foot. If
the needle hits the presser foot, the
needle may bend or break.
1
CAUTION
62
UTILITY STITCHES — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Basic Stitching
Straight stitches are used for sewing plain seams. Three stitches are available for basic stitching.
Basic stitching
1Baste or pin together the fabric pieces.
2Attach zigzag foot “J”.
• For details, refer to “Replacing the presser
foot” (page 33).
3Select a stitch.
• For details, refer to “Selecting stitching”
(page 56).
4Lower the needle into the fabric at the
beginning of the stitching.
5Start sewing.
• For details, refer to “Starting to sew”
(page 42).
• For details on sewing reverse/reinforcement
stitches, refer to “Securing the stitching”
(page 44).
6When sewing is finished, cut the thread.
• For details, refer to “Cutting the thread”
(page 45).
■Changing the needle position
With the straight stitch (left needle position) and
the triple stretch stitch, the needle position can be
adjusted. Sliding the stitch width adjustment slider
up moves the needle to the right; sliding the slider
down moves the needle to the left.
Memo
●The stitch width adjustment button needs to
be lit before using the slider to change the
needle position.
Stitch Name Pattern Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)] Presser
Foot
Auto Manual Auto Manual
Straight
stitch (left
needle
position)
00 Basic stitching and sewing
gathers or pintucks (left baseline/
reverse stitching)
0.0
(0) 0.0–7.0
(0–1/4) 2.5
(3/32) 0.2–5.0
(1/64–3/16)
J
Straight
stitch
(center
needle
position)
01 Basic stitching and sewing
gathers or pintucks (center
baseline/reverse stitching)
3.5
(1/8) 0.0–7.0
(0–1/4) 2.5
(3/32) 0.2–5.0
(1/64–3/16)
Triple
stretch
stitch
02 Reinforcing seams and sewing
stretch fabrics
0.0
(0) 0.0–7.0
(0–1/4) 2.5
(3/32) 1.5–4.0
(1/16–3/16)
J
72
UTILITY STITCHES — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Zipper Insertion
A zipper can be sewn in place.
There are many methods for inserting zippers. The procedures for inserting a centered zipper and a side zipper
are described below.
Inserting a centered zipper
Stitching is sewn on both pieces of fabric butted
against each other.
1 Right side of fabric
2 Stitching
3 End of zipper opening
1Attach zigzag foot “J” and sew straight
stitches up to the zipper opening.
With the right sides of the fabric facing each
other, sew reverse stitches after reaching the
zipper opening.
• For details, refer to “Basic Stitching”
(page 62).
2Using a basting stitch, continue sewing to the
edge of the fabric.
1 Basting stitching
2 Reverse stitches
3 Wrong side of fabric
4 End of zipper opening
3Press open the seam allowance from the
wrong side of the fabric.
1 Wrong side of fabric
4Align the seam with the center of the zipper,
and then baste the zipper in place.
1 Wrong side of fabric
2 Basting stitching
3 Zipper
5Attach the presser foot holder to the right pin
of zipper foot “I”.
1 Pin on the right side
2 Needle drop point
• For details, refer to “Replacing the presser
foot” (page 33).
Stitch Name Pattern Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)] Presser
Foot
Auto Manual Auto Manual
Straight
stitch
(center needle
position)
01 Attaching zippers
Sewing concealed seams and
pintucks
3.5
(1/8)
0.0–7.0
(0–1/4)
2.5
(3/32)
0.2–5.0
(1/64–3/16) I
1
2
3
1
2
3
4
1
1
2
3
I
1
2
Zipper Insertion 73
3
6Select stitch 01 .
• For details, refer to “Selecting stitching”
(page 56).
7Topstitch around the zipper.
1 Stitching
2 Right side of fabric
3 Basting stitching
4 End of zipper opening
8Remove the basting stitching.
Inserting a side zipper
Stitching is sewn on only one piece of fabric. Use
this type of zipper application for side openings and
back openings.
1 Stitching
2 Right side of fabric
3 End of zipper opening
The following procedure will describe how to stitch
on the left side, as shown in the illustration.
1Attach zigzag foot “J” and sew straight
stitches up to the zipper opening.
With the right sides of the fabric facing each
other, sew reverse stitches after reaching the
zipper opening.
• For details, refer to “Basic Stitching”
(page 62).
2Using a basting stitch, continue sewing to the
edge of the fabric.
1 Basting stitching
2 Reverse stitches
3 Wrong side of fabric
4 End of zipper opening
3Press open the seam allowance from the
wrong side of the fabric.
1 Wrong side of fabric
●When using zipper foot “I”, be sure to
select the straight stitch (center needle
position), and slowly turn the handwheel
toward you (counterclockwise) to check
that the needle does not touch the
presser foot. If a different stitch is
selected or the needle hits the presser
foot, the needle may bend or break.
●When sewing, be sure that the needle
does not touch the zipper, otherwise the
needle may bend or break.
CAUTION
1
2
3
4
CAUTION
1
2
3
1
2
3
4
1
Zipper Insertion 75
3
0Close the zipper, turn over the fabric, and then
baste the other side of the zipper to the fabric.
1 Basting stitching
aAttach the presser foot holder to the other pin
of zipper foot “I”.
If the presser foot holder was attached to the
right pin in step 6, change it to the left pin.
1 Pin on the left side
2 Needle drop point
bTopstitch around the zipper.
Sew reverse stitches at the end of the zipper
opening and align the zipper teeth with the
side of the presser foot.
1 Right side of fabric
2 End of zipper opening
3 Reverse stitches
4 Beginning of stitching
5 Basting stitching
cWhen you are about 5 cm (2 inches) from the
end of the zipper, stop the sewing machine
with the needle lowered (in the fabric), raise
the presser foot lever, and then open the
zipper and continue sewing.
dRemove the basting stitching.
●When sewing, be sure that the needle
does not touch the zipper, otherwise the
needle may bend or break.
1
I
2
1
1
2
3
4
5
CAUTION
Reinforcement Stitching 83
3
Reinforcement Stitching
Reinforce points that will be subject to strain, such as sleeve holes, inseams and pocket corners.
Triple stretch stitching
Use triple stretch stitching to reinforce sleeve holes
and inseams.
1Attach zigzag foot “J”.
• For details, refer to “Replacing the presser
foot” (page 33).
2Select stitch 02 .
• For details, refer to “Selecting stitching”
(page 56).
3Start sewing.
• For details, refer to “Starting to sew”
(page 42).
Bar tack stitching
Bar tacks are used to reinforce points subject to
strain, such as pocket corners and openings.
As an example, the procedure for sewing bar tacks at
pocket corners is described below.
1Determine the desired length of the bar tack.
Set the button guide plate on buttonhole foot
“A” to the desired length. (The distance
between the markings on the presser foot scale
is 5 mm (3/16 inch).)
1 Presser foot scale
2 Length of bar tack
3 5 mm (1/8 inch)
• A bar tack with a maximum length of about
28 mm (1–1/8 inches) can be sewn.
Stitch Name Pattern Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)] Presser
Foot
Auto Manual Auto Manual
Triple
stretch
stitch
02 Reinforcing the seams of sleeves
and inseams
0.0
(0)
0.0–7.0
(0–1/4)
2.5
(3/32)
1.5–4.0
(1/16–3/16) J
Bar tack
stitch
47 Reinforcing the ends of openings,
such as the corners of pockets
2.0
(1/16)
1.0–3.0
(1/16–1/8)
0.4
(1/64)
0.3–1.0
(1/64–1/16) A
J
1
2
3
Eyelet Stitching 85
3
Eyelet Stitching
Eyelets, such as those on belts, can be sewn. Three sizes of eyelets are possible: 7 mm, 6 mm and 5 mm
(1/4, 15/64 and 3/16 inch).
1Attach monogramming foot “N”.
• For details, refer to “Replacing the presser
foot” (page 33).
2Select stitch 49 .
• For details, refer to “Selecting stitching”
(page 56).
3Adjust the stitch width to select the desired
eyelet size.
• For details, refer to “Adjusting the stitch
width” (page 47).
4Lower the needle into the fabric at the
beginning of the stitching, and then lower the
presser foot lever.
5Start sewing.
XOnce sewing is completed, the machine
automatically sews reinforcement stitches,
then stops.
6Use the eyelet punch to cut a hole in the
center of the eyelet.
• When using the eyelet punch, place thick
paper or some other protective sheet under
the fabric before punching the hole in the
fabric.
Memo
● If light weight thread is used, the stitching
may be sparse. If this occurs, sew the eyelet
twice before removing the fabric, one on
top of the other.
Stitch Name Pattern Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)] Presser
Foot
Auto Manual Auto Manual
Eyelet stitch
49 Sewing eyelets, for example, on
belts
7.0
(1/4)
7.0, 6.0 or 5.0
(1/4, 15/64
or 3/16)
– – N
7 mm
(1/4 inch)
6 mm
(15/64 inch)
5 mm
(3/16 inch)

Specyfikacje produktu

Marka: Baby Lock
Kategoria: maszyna do szycia
Model: Crafters Choice BLCC2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Baby Lock Crafters Choice BLCC2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje maszyna do szycia Baby Lock

Baby Lock

Baby Lock Imagine 2 Instrukcja

12 Stycznia 2025
Baby Lock

Baby Lock Ellure - BLR Instrukcja

11 Stycznia 2025
Baby Lock

Baby Lock Accomplish 2 Instrukcja

30 Września 2024
Baby Lock

Baby Lock Ellisimo Gold BLSOG Instrukcja

22 Września 2024
Baby Lock

Baby Lock BL200A Elizabeth Instrukcja

22 Września 2024
Baby Lock

Baby Lock Joy Instrukcja

22 Września 2024
Baby Lock

Baby Lock Aria Blar Instrukcja

22 Września 2024
Baby Lock

Baby Lock BL67 Audrey Instrukcja

22 Września 2024
Baby Lock

Baby Lock Ovation - BLES8 Instrukcja

22 Września 2024
Baby Lock

Baby Lock BL20A Anna Instrukcja

21 Września 2024

Instrukcje maszyna do szycia

Najnowsze instrukcje dla maszyna do szycia

Husqvarna

Husqvarna Prelude 370 Instrukcja

8 Kwietnia 2025
Janome

Janome Mystical Mint Instrukcja

5 Marca 2025
Dürkopp Adler

Dürkopp Adler 1265-7 Instrukcja

4 Marca 2025
Brother

Brother Innov-is 15P Instrukcja

1 Marca 2025
Janome

Janome 41012 Instrukcja

24 Lutego 2025
Janome

Janome Fast Lane Fucshia Instrukcja

24 Lutego 2025
Janome

Janome Blue Couture Instrukcja

24 Lutego 2025
Janome

Janome Horizon 7700 Instrukcja

24 Lutego 2025
Husqvarna-Viking

Husqvarna-Viking Hiclass 100Q Instrukcja

18 Lutego 2025
SilverCrest

SilverCrest SNM 33 B2 Instrukcja

17 Lutego 2025