Instrukcja obsługi AXESS AXGMLN-08

AXESS Niesklasyfikowane AXGMLN-08

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AXGMLN-08 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Installation instructions for part AXGMLN-08

REV. 5/6/2020 INSTAXGMLN-08

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power

(12-volt 10-amp)

• Retains R.A.P. (retained

accessory power)

• Provides NAV outputs (parking

brake, reverse, and speed sense)

• Retains chimes

• Retains OnStar/OE Bluetooth

• Adjustable OnStar level

• Designed for non-amplified

models, or when bypassing

a factory amp

• Retains balance and fade

• AXUSB-CBL updatable

(sold separately)

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

AXGMLN-08

GM Data Interface

2012-2016

APPLICATIONS

• AXGMLN-08 interface • AXGMLN-08 harness

• 16-pin harness with stripped leads

INTERFACE COMPONENTS

Connections to be made 2 ...................................................

Installing the AXGMLN-08 3 ................................................

Initializing the AXGMLN-08 3 ..............................................

Adjusting the AXGMLN-08 3 ................................................

Table of Contents

CHEVROLET

Avalanche † * 2012-2013

Express † 2013-2015

Malibu (with single color,

monochrome

display) * 2013-2015

Malibu Limited (

with single color,

monochrome display) * 2016

CHEVROLET (CONT)

Silverado 2500/3500 † * 2014

Silverado † * 2012-2013

Suburban † * 2012-2014

Tahoe † * 2012-2014

Trax * 2015-2016

GMC

Savana † 2013-2015

Sierra 2500/3500 † * 2014

Sierra † * 2012-2013

Yukon/Yukon XL † * 2012-2014

* These vehicles have an amplifier option. Please reference the “Service Parts Identification” sticker located in the

glove box for the RPO code UQ7 or Y91. If UQ7 or Y91 are present, then the vehicle is equipped with an amplifier.

Either use the AXGMLN-07 interface, or bypass the amplifier.

† Only for models with NAV.

AXGMLN-08

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the wire to the accessory wire.Red

Note: If installing an AXSWC (sold separately), there will be an accessory wire

there to connect as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White

wire to it.

• If the aftermarket radio has a mute wire, connect the wire to it. If the Brown

mute wire is not connected, the radio will turn off when OnStar is activated.

• Connect the wire to the right front positive speaker output.Gray

• Connect the wire to the right front negative speaker output.Gray/Black

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require

these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wireLight Green

From the AXGMLN-08 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative output.Purple/Black

• The Black/Yellow wire is used for OnStar level adjustment for models that

do not come equipped with steering wheel controls. Refer to the OnStar level

Adjustment section for further instructions.

12-pin pre-wired AXSWC harness:

• This harness is to be used along with the optional AXSWC (not included) to

retain steering wheel audio controls. If the AXSWC is not being used, disregard

this harness. If it will be used, please refer to the AXSWC instructions for radio

connections and programming.

Note: Disregard the harness that comes with the AXSWC.

• Connect the wire to the accessory wire.Red

Note: The relay attached to the AXGMLN-08 harness is only for audible turn

signal clicks. No extra steps are required to retain this feature, so leave the

relay as-is.

Connections to be made

AXGMLN-08

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AXGMLN-08 harness,

into the interface.

• Connect the AXGMLN-08 harness to the wiring harness in the vehicle.

Note: If using the AXSWC, connect it after you initialize and test the

AXGMLN-08, with the key in the off position.

OnStar Level Adjustment

• Press the OnStar button to activate it.

• While OnStar is speaking, press the VOLUME UP or VOLUME DOWN button on

the steering wheel to raise or lower the OnStar level.

• If the vehicle does not come equipped with steering wheel controls, locate the

Black/Yellow

wire on the AXGMLN-08 harness.

•

While OnStar is speaking, tap the Black/Yellow wire to ground. Once the OnStar level

is set, it will stay at that level until the Black/Yellow wire is tapped to ground again

Attention! If the interface loses power for any reason, the following steps will need

to be performed again. Also, if installing an AXSWC connect it after you initialize and

test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, and then to the accessory position. Test all

functions of the installation for proper operation, before reassembling the dash.

Initializing the AXGMLN-08

Installing the AXGMLN-08 Adjusting the AXGMLN-08

Specyfikacje produktu

Marka:	AXESS
Kategoria:	Niesklasyfikowane
Model:	AXGMLN-08

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AXGMLN-08, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024

AXESS 99-7014HG Instrukcja

8 Października 2024

AXESS AXGM-17 Instrukcja

8 Października 2024

AXESS AXGMLN-34 Instrukcja

8 Października 2024

AXESS 99-7382HG Instrukcja

8 Października 2024

AXESS GMOS-12 Instrukcja

8 Października 2024

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024

AXESS 99-7510HG Instrukcja

8 Października 2024

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024