Instrukcja obsługi AXESS AXGMLN-01

AXESS Niesklasyfikowane AXGMLN-01

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AXGMLN-01 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Installation instructions for part AXGMLN-01

REV. 8/6/2020 INSTAXGMLN-01

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake,

reverse, speed sense)

• Pre-wired AXSWC harness (AXSWC sold

separately)

• Retains chimes to the factory speaker

• Adjustable chime level

• Retains OnStar / OE Bluetooth

• Adjustable OnStar level

• Retains the factory backup camera

• Designed for non-amplified models, or

when bypassing a factory amp

• Retains balance and fade

• Includes an antenna adapter

• AXUSB-CBL updatable (sold separately)

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

• Small flat-blade screwdriver

TOOLS REQUIRED

AXGMLN-01

GM Data Interface

2006-Up

• AXGMLN-01 interface • AXGMLN-01 harness

• 16-pin harness with stripped leads • Backup camera harness • Antenna adapter

INTERFACE COMPONENTS

Connections to be made 2-3 ................................................

Installing the AXGMLN-01 3 ................................................

Initializing the AXGMLN-01 3 ..............................................

Adjusting the AXGMLN-01 4 ................................................

Table of Contents

APPLICATIONS

See inside front cover

AXGMLN-01

Applications

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the wire to the accessory wire.Red

Note: If installing an AXSWC (sold separately), there will be an accessory wire

there to connect as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White

wire to it.

• If the aftermarket radio has a mute wire, connect the wire to it. If the Brown

mute wire is not connected, the radio will turn off when OnStar is activated.

• Connect the wire to the right front positive speaker output.Gray

• Connect the wire to the right front negative speaker output.Gray/Black

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

Connections to be made

† These vehicles are standard for a factory amplifier. Either use the AXGMLN-02 interface,

or bypass the amplifier.

‡ Only for models without NAV in 2011-2015. For models with NAV, use the AXGMLN-08.

∆ Only for models without NAV in 2012-up. For models with NAV, use the AXGMLN-08.

BUICK

Enclave 2008-up

Lucerne 2006-2011

CADILLAC

DTS † 2006-2011

Escalade † 2007-2014

SRX † 2007-2009

CHEVROLET

Avalanche ∆ 2007-2013

Captiva Sport 2012-2015

Equinox 2007-2009

Express ‡ 2008-up

Impala 2006-2013

Impala Limited 2014-2016

Monte Carlo 2006-2007

Silverado (new body) ∆ 2007-2013

Silverado 2500/3500 ∆ 2014

Suburban ∆ 2007-2014

Tahoe ∆ 2007-2014

Traverse 2009-up

GMC

Acadia 2007-2016

Acadia Limited 2017

Savana ‡ 2008-up

Sierra 2500/3500 ∆ 2014

Sierra (new body) ∆ 2007-2013

Yukon / Yukon XL ∆ 2007-2014

HUMMER

H2 † 2008-2009

PONTIAC

Torrent 2007-2009

SATURN

Outlook 2007-2010

Vue 2008-2010

SUZUKI

XL-7 2007-2009

AXGMLN-01

Connections to be made

From the AXGMLN-01 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

• The Black/Yellow wire is used for OnStar level adjustment for models that

do not come equipped with steering wheel controls. See the OnStar level

Adjustment section for further instructions.

12-pin pre-wired AXSWC harness:

• This harness is to be used along with the optional AXSWC (not included)

to retain steering wheel audio controls. If the AXSWC is not being used,

disregard this harness. If it will be used, please refer to the AXSWC

instructions for radio connections and programming.

Note: Disregard the harness that comes with the AXSWC.

• Connect the wire to the accessory wire.Red

Note: The relay attached to the AXGMLN-01 harness is only for audible turn signal

clicks. No extra steps are required to retain this feature, so leave the relay as-is

Backup camera harness (if applicable):

• If retaining the factory backup camera, connect the Yellow RCA jack to the

backup camera input of the aftermarket radio.

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AXGMLN-01 harness,

into the interface.

• Connect the AXGMLN-01 harness to the wiring harness in the vehicle.

• If using the AXSWC, connect it after you initialize and test the AXGMLN-01, with

the key in the off position.

• If applicable, connect the backup camera harness to the wiring harness in the

vehicle. This harness is located behind the radio.

Attention! If the interface loses power for any reason, the following steps will need

to be performed again. Also, if installing an AXSWC connect it after you initialize and

test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, pause for a moment, and then to the accessory

position. Test all functions of the installation for proper operation, before

reassembling the dash.

Installing the AXGMLN-01

Initializing the AXGMLN-01

Specyfikacje produktu

Marka:	AXESS
Kategoria:	Niesklasyfikowane
Model:	AXGMLN-01

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AXGMLN-01, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024

AXESS 99-7014HG Instrukcja

8 Października 2024

AXESS AXGM-17 Instrukcja

8 Października 2024

AXESS AXGMLN-34 Instrukcja

8 Października 2024

AXESS 99-7382HG Instrukcja

8 Października 2024

AXESS GMOS-12 Instrukcja

8 Października 2024

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024

AXESS 99-7510HG Instrukcja

8 Października 2024

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024